Audio Impedance
-
Product
2-Tone Audio Generator
-
* 2 tones, 1900 & 700 Hz * 200 mv output * balance & level controls * Individual tone muting *Microphone level output* measures 4.5 x 2.5 x 1.1 inches* 9 volt battery operation
-
Product
Audio Volume Meter
AVM
-
This is a true RMS audio storage meter used to measure audio volume levels of live program material. Use it to periodically survey your system for high or low audio levels to prevent complaints about loud or un-even audio programming. You can use this meter to quickly locate and verify any objectionable signals levels and bring them into compliance.
-
Product
Audio Generator
AG-51
-
The AG-51 Audio Generator contains a low distortion 20 Hz to 200 kHz sine wave generator, an SMPTE standard intermodulation signal generator and a fixed frequency sine wave generator at 3.15 kHz for wow and flutter tests. Signal outputs are simultaneously available at levels of up to +20 dBm (equivalent sine wave power for complex signals) at separate left (L OUT) and right (R OUT) output connectors. Outputs may be selected for left (L) only, right (R) only, left and right in phase (L+R), and left and right in phase opposition (L-R). Fully balanced or unbalanced outputs at impedance levels 150 ohms or 600 ohms are front panel selectable. Three precision attenuators (10, 1.0 and 0.1 dB) provide a dynamic range of 99.9 dB in 0.1 dB steps. Attenuator dials display the output level directly in dBm in the 150 ohm source impedance configuration. Automatic output leveling circuitry with a built-in self-test feature provides a constant output level thereby eliminating the need for output metering. In the TEST mode the generator output level is reduced to zero, a useful feature during noise measurements.
-
Product
Audio Analyzer and Digital Audio Bus Module
DP-cPCI-5667
-
DP-cPCI-5667 is a 6U cPCI Audio Analyzer and Digital Audio Bus Module. This card implements low speed digital audio bus, high speed digital audio bus and audio analyzer features. It is used for general purpose analogue audio analysis and supports low speed digital audio bus and high speed digital audio bus protocols.
-
Product
Axia Audio
-
The foundational technology in all Axia products is Livewire plus AES67—we call it Livewire+—an AoIP protocol that enables high-reliability, low-delay uncompressed digital audio over Ethernet, including audio, logic, control, and program associated data (PAD). Devices connect together using standard Ethernet cables; audio and control routing is accomplished with off-the-shelf Ethernet switches. Axia Livewire+ has built-in compliance with the AES67 standard. That's because Axia and the Telos Alliance are committed proponents of AoIP interoperability—first as charter, supporting members of the X192 Working Group that defined AES67, and now as founding members of the Media Networking Alliance, a group of prominent equipment manufacturers formed to actively promote the adoption and implementation of the AES67 standard.
-
Product
Mini-ITX SBC With Intel® Celeron® Processor N3350 & Pentium® Processor N4200, VGA, HDMI, LVDS, USB 3.0, PCI Express Mini Card Slot, M.2, And HD Audio
MANO310
-
*Intel® Celeron® N3350 & Pentium® N4200 (optional)*2 DDR3L SO-DIMM for up to 8GB of memory*1 PCI Express Mini Card slot and PCIe x1*4 USB 3.0 and 2 USB 2.0*1 SATA-600, 1 M.2 and 1 SDXC slot*6 COM supported*12 to 24 VDC*VGA, HDMI and LVDS with triple-view supported
-
Product
Audio IP
-
We provide high-performance, compact, low power and customizable audio analog mixed-signal IP in leading foundry processes, including a wide range of ADC, DAC, CODEC and Voice Activity Detectors.
-
Product
Audio Panel/Amplifier Test Fixture
TA-200
-
The Model TA-200 test panel was designed to allow Avionics shops the capability to test and troubleshoot both today's new generation audio panels as well as the standard audio panels of the past. The testing of these panels over the years has always proven to be a very time consuming job for most shops because of the limited capabilities of any past test panels.
-
Product
Telecom Audio Test Sets
-
Networked Communication Solutions, LLC
Handheld test instruments for complete troubleshooting of audio frequency impairments on communication networks.
-
Product
Audio Video Controllers
-
Most of our cameras can operated remotely. The controllers allow to control the functions of the cameras:– Zoom– Focus– Audio– Pant/Tilt– optionally iris– LANThe controllers convert the optical signal to electrical signalsFor most controllers there is the option to integrate an Ethernet interfaceMost of the controllers can be equipped with an option for shielded intercom. The microphone is either integrated in the housing or a separate microphone can be used.If more than one camera is in use (e.g. one fixed and one mobile camera) multi controllers allow to control several cameras with one device.Up to 4 cameras can be connected to one multi controller. Each camera can be connected to a separate monitor each one monitor can show the selected camera.
-
Product
Audio Spectrum Analyzer
Spectrum Pad
-
Spectrum Pad turns your iPhone, iPad or iPhone Touch into an audio spectrum analyzer. Frequencies up to 20 kHz can be displayed.
-
Product
LED Audio Spectrum For IOS
-
LED Audio Spectrum uses your iPhone or iPad microphone to visualize sound through fluid, colorful graphics that bounce to the beat! Now you can actually "see" any surrounding sound such as speech, music, singing and more. The app comes with a handful of simple, yet outstandingly implemented visualizers and each has multiple color themes to choose from. The built-in TV out support gives you the big picture!
-
Product
Audio Oscillator & Sweep Generator
SweepGen
-
SweepGen turns a PC into an Audio Oscillator and Sweep Generator which can be used for testing audio or educational purposes. In conjunction with audio test instruments, you can make frequency response plots. SweepGen uses the sound card in your PC to produce sine waves that are mathematically correct almost to CD quality, indeed it's more likely that the quality of your PC sound card will be the limiting factor rather than the code in SweepGen.
-
Product
Audio Analyzer
MS20
-
The MiniSonic MS20 is a combined oscillator and measuring set in a stand-alone unit, which is both compact and portable. As well as being a quality tester the MS20 is a precision line-up tool, a stereo PPM, a balanced-unbalanced convertor (both ways), a stereo microphone pre-amp, a headphone amp, and a level convertor.
-
Product
Audio Multimeter
AMM-1
-
The purpose of this tool is to enable the user to: Measure True Amplifier Power output into any load reactive or resistive Measure Common DC voltages Measure DC voltage drops during quick transients on cable runs or battery / charging systems Measure Impedance of speakers at any power or frequency from 20Hz - 1kHz (box rise) Measure Phase Difference between Voltage and Current into reactive loads (Power Factor) Find Tuning Frequency of subwoofer enclosures Tune subwoofer enclosures for maximum power transfer Measure AC Volts (amplifier output) Measure AC Amps (amplifier output)
-
Product
3.5" Embedded SBC With AMD G-Series APU, AMD A50M, LVDS/VGA, Dual LANs And Audio
CAPA111
-
Based on the new low-power AMD G-Series APU T40R/T40E with AMD FCH A50M chipset, Axiomtek developed CAPA111 low power graphics-oriented 3.5" embedded board for digital signage, gaming, medical imaging, kiosks/POS, thin clients, and factory automation. The CAPA111 is powered by either a single core AMD G-Series APU T40R at 1.0GHz or the dual core T40E at 1.0 GHz paired with the A50M FCH chipset and one DDR3 1066 memory slot supports up to 4 GB. Integrated with Radeon™ HD 6250 graphics controller with DirectX 11 support, the super compact 3.5" embedded platform delivers unprecedented high definition visual experience and features 18/24-bit LVDS and VGA display dual view compatibility. Moreover, the embedded board only requires +12V DC power input.
-
Product
LCR Component Meter with Component Impedance Measurement
LCR45
-
The new LCR45 does everything that the popular LCR40 does, but we've added some significant enhancements. The LCR45 features a new high capacity micro and high resolution ADCs.*Fluid measurements of L, C and R (continuous readings with selectable hold function).*Fine resolution for improved performance at low inductance/capacitance/resistance.*Auto and Manual component type.*Auto and Manual test frequency.*Frequencies: DC, 1kHz, 15kHz and 200kHz.*Display of component values, complex impedance, complex admittance and magnitude/phase.
-
Product
Qseven V1.2 SoM Evaluation Kit With I.MX287 454 MHz (Industrial) SoC, 128MB Memory, 4GB EMMC, Gigabit Ethernet, Audio, CAN And BSP
Q7M100-100-EVK
-
*Ultra low power consumption ARM9*High flexibility Qseven v1.2 compliant design*5 UART*2 CAN*24-bit TTL LCD*10/100 Mbps Ethernet*Linux 2.6.35
-
Product
I/O Board With Two COM, Four USB 2.0 And Audio For PICO312, PICO313, PICO511, PICO512
AX93A09
-
*Specification: 1 x RS-232/422/485, 1 x RS-232, 4 x USB 2.0, 1 x Audio (MIC-in/Line-out), 1 x Power-on, 1 x Reset, 2 x LED*Dimensions: 118 x 29 mm*Compliant products: PICO312, PICO313, PICO511, PICO512
-
Product
High Impedance Preamplifier
1671
-
The Model 1671 is a single ended low noise field effect transistor
-
Product
Omnia Audio
-
Omnia Audio—part of the Telos Alliance—was founded by Frank Foti, who used audio engineering/processing to enable stations to craft a unique ‘signature sound’ that was louder than anything else on the air, yet with clear sound and minimal distortion. This processing is at the core of Omnia products, allowing stations to stand out among the competition on a crowded dial. Omnia has continued to innovate with leading-edge and solutions-oriented broadcast audio technology and numerous accolades and awards under its belt. In fact, Omnia is now the brand leader in Audio Processing, Processing/Encoding for Streaming Audio, Voice Processing, Analysis Tools, and Studio Audio Processing. Its products are the choice of the majority of the Top 100 rated stations in America, and are used at most major stations worldwide. Omnia continues to push the envelope to give broadcasters the tools they need to amplify, customize, and perfect sound signatures. For a side-by-side comparison of all Omnia Products, click here.
-
Product
3.5” Embedded SBC With Intel® Pentium® Processor N4200 & Celeron® Processor N3350, LVDS, HDMI, 2 GbE LANs And Audio
CAPA313
-
The CAPA313 is powered by the Intel® Pentium® processor N4200 or Intel® Celeron® processor N3350 (codename: Apollo Lake). This 3.5" embedded board was designed for operational stability in harsh environments with a wide operating temperature range from -20°C to +70°C. It offers a wide range DC input of 12V to 24 for various industrial environments. It also comes with rich I/O connectors, stunning graphical performance and an emphasis on expandability. In addition to one 204-pin DDR3L-1867 SO-DIMM socket supporting system memory up to 8GB, the CAPA313 has one PCI Expess Mini Card slot for 3G/4G, GPS, Wi-Fi and Bluetooth connection. The compact-size embedded board comes with one RS-232/422/485, one RS-232, two USB 2.0, four USB 3.0, eight-channel digital I/O, audio, LVDS, HDMI, VGA (optional) and dual Gigabit LANs with Intel® i211AT Ethernet controller. It also features one SATA-600 socket and one mSATA interface for storage devices. To ensure reliable operation, the 3.5” embedded SBC supports watchdog timer and hardware monitoring features.
-
Product
High Impedance Active Probes
7
-
Designed as a companion probe to Models 12C and 18C for driving integrated circuit lines so the Model 12C and 18C can be used to measure the response of adjacent nodes. The Model 7 consists of a flexible 6 foot, 50 ohm coaxial cable accurately terminated to 50 ohms in order to avoid undesirable reflections. A special miniature connector receives replacement coaxial probe tips that provide a shielded environment to within 3 mm of the fine tungsten probe point, thus minimizing capacitive coupling to other parts of the circuit. The replaceable coaxial probe tips are offered in various point sizes and can also be bent to any shape in order to accommodate a variety of probing geometries.
-
Product
3.5" Embedded SBC With LGA1151 Socket For 7th/6th Gen Intel® Core™ I7/i5/i3 Processor, LVDS, VGA, HDMI, 2 GbE LANs And Audio
CAPA500
-
The CAPA500 features the LGA1151 socket 7th generation Intel® Core™ processor family (codename: Kaby Lake) with 35W TDP (thermal design power), as well as the Intel® H110 chipset (Q170 optional). The CAPA500 supports one 260-pin DDR4-2400 SO-DIMM with a memory capacity up to 16GB for extensive storage. The compact 3.5-inch embedded motherboard also offers display outputs through HDMI, VGA and LVDS for triple independent display applications. Moreover, the compact-sized embedded board runs on +12 VDC power, supporting auto power-on. It can operate at a wide range of temperatures from -20°C to 60°C under active thermal control. The 146 mm x 104 mm embedded SBC is suitable for IoT/M2M-related, industrial control, self-service terminal, digital signage, POS, kiosk and many other applications where high-speed processing and graphics performance under limited space is required.
-
Product
Pico-ITX SBC With 6th Gen Intel® Core™ I7/i5/i3 & Celeron® Processors, HDMI/LVDS, LAN And Audio
PICO500
-
The PICO500, an extreme compact pico-ITX embedded board, supports the latest 14nm 6th generation Intel® Core™ i7/i5/i3 processors (Codename: Skylake-U). The tiny PICO500 is equipped with one DDR4 SO-DIMM with up to 16 GB memory capacity. Integrated with Intel® HD graphic engine, the Pico-ITX motherboard supports HDMI and 18/24-bit dual channel LVDS that delivers a whole new level of Ultra HD 4K visual experiences. Its Pico-ITX form factor allows for an extremely compact performance system; meanwhile, the PICO500 is built to withstand wide temperature conditions, ranging from -20°C to +70°C (-4°F to +158°F) with active thermal solution.
-
Product
Online Audio Frequency Signal Generator
WavTones
-
We are proud to offer not only the best audio frequency signal generator on the net, but also a high-end sound generator, which compares favorably to the more expensive software and hardware tone generators!
-
Product
High Impedance Differential Module
HID
-
Use the HID module in conjunction with a high-speed overcurrent relay to provide three phase high impedance differential protection for substation busbars of any voltage level. Additionally, it can also be used to protect electrical machines like transformers, generators or motors against restricted ground faults.
-
Product
Audio Autoselector
1177A
-
The 1177A is a unique four input, one output digital audio switcher, incorporating technologies such as AutoSelect automatic input switching and digital audio automatic cross-conversion. This sturdy product is perfect for adding digital audio inputs to a Bose Lifestyle system, or a legacy A/V receiver that has very few digital inputs. Supports both digital optical and digital coaxial audio types.
-
Product
SMARC V1.0 SoM With IMX6 Quad/DualLite 800 MHz (Industrial) SoC, 1GB RAM, 4GB EMMC, GbE LAN, Audio, CAN, MIPI And PCAM
SCM120
-
*SMARC 1.0 (82 x 50 mm)*Ultra low power consumption Cortex™-A9*2 CAN 2.0B*24-bit TTL signal*LVDS/HDMI 1080P*10/100/1000 Mbps Ethernet*Linux3.0.35/Android 4.3*Audio
-
Product
Sophisticated Audio and Video Test Patterns
VQL
-
VQL Instantly reveals your video display, codec, scaler, converter or other video device performance VQL test patterns cover all 3 levels of video QA/QC: Instant visual-aural Quality Estimation Objective Measurements of video and audio performance Fully automated (unattended) Quality Control VQL features: Compatibility with all commonly used software or hardware codecs and media players VideoQ VQV / VQMA / VQTS / VQDM compatible tests Wide range of video frame sizes: from 192x108 to 4096x3072 Variety of bit rates up to uncompressed 4:4:4 4K @60 fps, 48 bit per pixel Variety of video and audio formats, color spaces and level schemes All test patterns remain suitable for accurate measurements even after low bitrate coding, heavy scaling and/or cropping, e.g. after down-conversion for mobile devices Standard, custom and semi-custom tests for development labs, content processing facilities, CDN systems, software developers and high volume manufacturers
