Filter Results By:
Products
Applications
Manufacturers
Magnetic Field Meters
Measure magnetic flux density/field strength.
See Also: Magnetic Field, Magnetic Field Mapping, Magnetic Field Probes, Magnetic Field Sensors, Magnetic Field Test
-
product
Magnetic Radiation (Gauss Meter)
A gauss meter can detect either static (DC) permanent (rare-earth) magnetic or dynamic (AC) electromagnetic fields (EMFs), or both.
-
product
Handheld Gaussmeter
HGM09
Data storage on a personal computer via keystroke. The HGM09s is easy to use and has a good price/performance ratio. The handheld gaussmeter HGM09s is used to measure magnetic DC and AC fields. The measurands are flux density in Tesla or Gauss and the field strength in Amps per meter.
-
product
Intelligent Digital Gauss Meter / Tesla Meter
DX-150
DX-150 Full-Digital Gauss/Tesla Meter is designed for applications requiring high precision, high-resolution magnetic field measurement. It is an intelligent solution against the traditional analog, digital table header type Gauss / Tesla meter.
-
product
Microrad RF Fieldmeter
Users can measure from static/almost static magnetic fields up to 6GHz utilising only two probes while remaining compliant with Directive 2013/35/EU. This solution is the NHT-3D meter plus 33P and 01E probes
-
product
Primary Cable Fault Locating
Directional Impulse Detector
The Directional Impulse Detector ( D.I.D.) is a compact handheld detector used to locate primary cable faults by sensing the magnetic field generated by the current pulse from a high voltage discharge device (thumper). A meter deflection indicates the intensity of the received signal. No deflection indicates that you have walked beyond the fault or away from the cable.
-
product
Antenna, Loop
EM-6871 | 30 Hz – 1 MHz
The EM-6871 Antenna can be used with any 50 ohm /Receiver/Field Strength Meter to obtain magnetic field measurements from 30 Hz to 1 MHz.
-
product
SparkFun Triple Axis Magnetometer Breakout
MLX90393 (Qwiic)
It's time to start utilizing the superior magnetometer, and what better way than to throw it onto an easy-to-use breakout board? The SparkFun MLX90393 Magnetometer Breakout is a triple-axis magnetic sensor board capable of sensing very small fields, while still behaving as one would expect during saturation in larger fields (like a nearby magnet). The MLX90393 breakout can be used as a compass sensor but also works well as a non-contact controller, a flow meter with a magnetic impeller, or a linear actuator position sensor. To make it even easier to to get your readings, all communication is enacted exclusively via I2C, utilizing our handy Qwiic system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.
-
product
Fluxmeter
Model 2130
The Model 2130 Fluxmeter is a fully featured, high-end Fluxmeter based measurement system. It is a compact instrument with high accuracy, automatic drift correction, microprocessor control, and twelve measurement ranges to allow the operator to configure the meter for maximum resolution and accuracy. The Model 2130 is capable of measuring (DC), alternating (AC), or pulsed magnetic fields. Selecting primary measurement functions is quick and easy with dedicated front panel function keys. An easy to use menu allows access to user defined parameters such as upper and lower magnetic limits and relative magnetic measurements.
-
product
Flux Meter
Star Trace Pvt. Ltd. is a renowned manufacturer and supplier of unbeatable quality Magnetic Field Flux Meters. The company manufactures these Magnetic Flux Meters from top-grade raw materials to ensure quality and performance. In order to ensure customers' satisfaction, these Magnetic Flux Meters are sent for several stringent quality control tests before supplying and exporting them to customers.
-
product
High Resolution LCD Encoders
HR-E® LCD
High Resolution LCD Encoders from Badger Meter are fully electronic, solid-state, field programmable and use industry standard ASCII communication protocols to provide high resolution encoded output. Status indicators/alarms can also be sent as part of the encoded output to endpoints capable of receiving extended messages. In addition, the HR-E LCD offers tamper-resistant features such as register removal and magnetic tamper indicators to provide utilities with increased security.
-
product
Gaussmeter
DX-102
DX-102 Gaussmeter is a portable gauss meter, based on the latest progress of Hall effect magnetic field measuring instrument, adopted DSP technology. Test probe adopts import GaAs linear Hall chip, the difference between any two probes is small, if damaged, it can be replaced directly. DX-102 Gaussmeter is an ideal DC magnetic field test instrument.
-
product
Reference Magnets
Series MT
The reasonably priced WUNTRONIC standard reference magnets offer the possibility in a simple way of being able to calibrate or to check magnet measuring instruments like Gauss Meter/Tesla Meter with the respectively accompanying probes in a defined magnetic field.
-
product
Turbine Flow Meters
Axial turbine flow meters are designed with wear resistant internal components to provide trouble-free operation and a long service life. Fluid entering the flow meter is first conditioned by the inlet flow straightener which reduces turbulence in the fluid. The moving fluid causes the rotor to spin at a speed that is proportional to its flow rate. As the turbine blades on the rotor pass through the magnetic field of the pickup, an electronic pulse is generated.
-
product
Triaxial ELF Magnetic Field Meter
SK-8301
Accurate measurement by- True RMS- Built-in XYZ triaxial sensorFor 40Hz to 1kHz magnetic field measurement.uT and mG are selectable.MAX/MIN and Average measurements.Compact and easy-to-carry.Easy operation by only 3-keys.
-
product
Single AXIS DIGITAL AC GAUSSMETER
IDR-109/IDR-119
Integrity Design and Reseach Corp.
Typical Applications include checking the 50 and 60 Hz electric and magnetic fields (EMF) produced by equipments such as transmission lines, computers, electric blankets, electric appliances, televisions, etc.. Magnetic fields are invisible radiations, the best method to detect them is by using one of the accurate gauss meter from Integrity Design & Research corp.
-
product
Magnetostatic probe
BS13
Three-dimensional measurement of magnetic equationsMeasuring range 100 TResolution 0.1 TAbsolute and relative measurementsFor connection to the field meter FM10Switching between total field strength and X, Y and Z proportions is possiblePermanent recording and saving of individual points with the field meter FM10LOutstanding value for moneyDimension 132 x 40 x 25 mm
-
product
Gaussmeter
DX-101
DX-101 Gaussmeter is based on the Hall effect magnetic field strength of the latest developments in instrumentation, the design of desktop-type Gauss meter. Maximum range 330.0mT and 3000mT two tranches, the minimum basic error of 1.0%. Test probe connectors is imported, stable and reliable connection.
-
product
Magnetic Field Meter
MP - 2000
The new magnetic field meter MP - 2000 first used probes (tangential and Axialfeldsonden), in which an own microcontroller, the analog sensor signals are digitized and linearized directly in the probe. This new technique is extremely trouble-free and allows very precise measurements, especially at high magnetic field strengths, where Hall probes can not operate linearly.
-
product
Zero Gauss Chamber
ZGC
The model ZGC zero gauss chamber reduces the environmental magnetic field (Earth field) to near zero inside the chamber. Any gaussmeter probe which is less than 9.4 mm or 0.370" diameter can be placed inside. The meter is then "zeroed", which means that it will read zero whenever the probe is subsequently placed in zero field. By using a zero gauss chamber, any offset error is therefore eliminated. The model ZGC is unique in that it contains a degausser (demagnetizer). This is situated between the inner and outer mu-metal shields. When the degauss button is pressed, any accidental magnetization of the chamber, no matter how strong, is erased. Accidental magnetization is a major problem with most zero gauss chambers and it has limited their use. If a magnet comes too close, the chamber will become "permanently" magnetized and will have an internal field that is typically 0.2 to 0.5 gauss. The chamber must then be degaussed because the Earth field is also around 0.5 gauss, so a magnetized zero gauss chamber will not significantly reduce the field.
-
product
3 Axis Magnetic Field Meters
Display: 4 digits LCD, maximum reading 9999 Range: 20/2000 mG,2/20/200TResolution: 0.1/1 mG or 0 .001/0 .01/0 .1 TAccuracy: (2.5%+5dgt) at 50Hz/60Hz (5.0%+5 dgt) at 30Hz-2000HzSensor: Triple AxisFrequency response: 30Hz to 2000HzOperating temperature & humidity: 5'Cto 40'C, below 80% RHWeight: About 230g
-
product
Calibration & Demag.
Model 8515-D
The Model 8515-D is a medium-energy, high voltage, and capacitor discharge type ringing demagnetizer capable of desaturating Ceramic and Rare Earth magnetic materials. The Model 8515-D is easily adapted to a wide range of production and laboratory demagnetizing requirements. A modern solid-state electronic control circuit, coupled with a rugged, heavy-duty discharge SCR and fixture, make this demagnetizer a highly reliable, low maintenance unit. The electronic voltage control circuit prevents the Model 8515-D from being discharged before the preset energy level has been reached, avoiding incomplete magnet desaturation. An easy to read front panel meter monitors the capacitor voltage. The energy storage level can be easily changed in the field. Integral electrical interlock and fail-safe circuitry provide a high degree of operator safety.
-
product
Magnetic Field Meters
Compliant with IEC/EN 62233 and ICNIRP 2010 guidelines Compliance testing of household appliances 10 Hz to 400 kHz Bundled with 100 cm^2 sensor
-
product
Magnetic Field Meter
Measurement for the magnetic field generated from Direct Current (DC, with display by N/S Magnetic polarity) or Alternating Current (AC in 40-500Hz).
-
product
Leakage Clamp Meter
KT-3084
Digital clamp meter designed for leakage current measurement. Least affected by external stray magnetic field. The minimum resolution is 0.1mA. Four AC current ranges:400mA/4A/40A/400A. Data hold function,peak hold function
-
product
Gauss Meters
A gauss meter displays electromagnetic wave measurements in Gauss (G), milliGauss (mG), milliTesla (mT) or microTesla (µT) units. A gauss meter can detect either static (DC) permanent (rare-earth) magnetic or dynamic (AC) electromagnetic fields (EMFs), or both. Thus, it is important to review the specifications of a gauss meter prior to purchase to ensure suitability for the intended application.Neodymium (NdFeB) permanent magnets are among the world's strongest and most widely used magnets. When testing magnets made of neodymium or other rare-earth elements, a gaussmeter or magnetometer capable of measuring DC magnetic fields is required. However, most electromagnetic fields encountered are generated by AC currents. Examples include electrical power lines, transformers and wiring for overhead lighting, solar panels and other electrical devices and equipment. Electromagnetic fields from electrical installations are believed to cause feelings of nervousness, anxiety and paranoia in EMF-sensitive human beings.Most gaussmeters offered by PCE Instruments can be calibrated and certified according to DIN ISO 9000 standards for an additional fee. Replacement gaussmeter probes and optional accessories are available for most gaussmeter models.
-
product
Magnetic Susceptibility Meter for Multi-Layer Survey
MULTI KAPPA
Multi Kappa instrument serves for fast field survey allowing both spot measurement and mapping by means of several probes. Together with GF Instruments traditional pocket magnetic susceptibility meters cover wide range of demands for accurate susceptibility measurement on ground surface, outcrops and samples of rock and soil. geological survey, archaeology, agriculture and forestry, raw material prospecting, mineralogy, sedimentology, detection of metallic objects, UXO survey.
-
product
PROFESSIONAL 3-AXIS EMF DIGITAL GAUSSMETER
FWBELL 4000 series
Integrity Design and Reseach Corp.
Typical Applications include checking the 50 and 60 Hz magnetic fields (EMF) produced by equipments such as AC Power Lines, Office Equipment, Video Display Terminals, Household Appliances, home and Building Inspection, etc.. Magnetic fields are invisible radiations, the best method to measure the strength fields is to use one of the accurate gauss meters offer by Integrity Design & Research corp.
-
product
Gaussmeter/Teslameter
Model 2100
The Model 2100 Gaussmeter is a fully featured, high-end Gaussmeter with a low cost Gaussmeter price. It is a compact, high accuracy, microprocessor controlled, flux density measuring instrument. The Model 2100 is capable of measuring static (DC), alternating (AC), or pulsed magnetic fields. Twelve measurement ranges allow the operator to configure the meter for maximum resolution and accuracy from 300mG (30 microTesla) to 300 kG (30 Tesla). Selecting primary measurement functions is quick and easy with dedicated front panel function keys. An easy-to-use menu allows access to user defined parameters such as upper and lower magnetic limits and relative magnetic measurements. Remote meter configuration is completely accessible using the built in RS-232 Interface or optional IEEE-488 Interface.
-
product
Protective Bonding Testers
RMO-E Series
The RMO-E instruments are designed and ideal for testing protective bonding (grounding) of equipment following the standard IEC 61010-1. Also, they can measure the resistance of high, middle and low voltage circuit breakers, high-current bus bar joints, cable splices, and welding joints. The instruments accurately measure not only in factory environments but also in high-induction fields and substations.Both models generate a true DC ripple-free (less than 1 %) current with automatically regulated test ramps. During a test, the protective bonding testers automatically generate increasing current before measuring and decreasing current after the measurement. Consequently, this significantly decreases magnetic transients and ensures great accuracy.These instruments can store up to 500 measurements in the internal memory and have a built-in thermal printer available as an option.DV Win software communicates with the RMO-E earth resistance meter via USB or RS232 interface. It allows a user to run the test remotely from PC, as well as to download test results, analyze and generate fully configurable test reports.The RMO-E series contains two models, RMO60E and RMO100E. The main difference between these two models is in the maximal test current:60 A DC for RMO60E100 A DC for RMO100E
-
product
Cable Identifier
K&S Engineering and Scientific Ltd
K&S Engineering and Scientific LTD's Cable Identifier Set offers the user a compact, portable solution for cable identification. Depending on the user preference, the Cable Function Generator and Cable Identifier Unit can be jointly housed in a rugged briefcase, or alternatively, for the user requiring a more rugged unit, can be delivered as two individual units each with their own carry-case. With the Cable Identifier Set, power optimum levels are selected by means of a rotary switch and the power levels are displayed on a meter located on the Cable Function Generator. As the Cable Identifier Unit is capable of detecting magnetic fields around mains cables it has the added advantage of the user being able to use this as a stand-alone unit to detect power cable configuration.
