Battery Charge Discharge
-
Product
Miniature, Battery Powered, Stand Alone Pressure and Temperature Data Logger
PRTemp101A
-
The PRTemp101 is a miniature, battery powered, stand alone pressure and temperature data logger. This is an all-in-one compact, portable, easy to use device that will measure and record data for up to 8,191 measurements per channel. The storage medium is non-volatile solid state memory, providing maximum data security even if the battery becomes discharged.
-
Product
Battery Charger-Dischargers & Monitors
-
It is a compact and multi-functional unit with three major functions: battery charger, battery discharger and battery activator. These three functions could be used individually or comprehensively to facilitate your daily work for battery maintenance. JUNXY single battery regenerator could be applied for different cell voltages, such as 2V, 6V & 12V single cell battery regenerator, while JUNXY battery string regenerator covers 24V, 48V, 110V, 220V battery strings with different charge/discharge current selectable.
-
Product
5V50mA Coin Cell Battery Test Equipment
TOB-5V50mA
-
Xiamen Tob New Energy Technology Co., Ltd
8 Channels Battery Test Equipment (0.1-50mA, up to 5V) For Lithium Coin Cell Battery Research. TOB-5V50mA Battery Test Equipment is an eight-channel battery analyzer to analyze small coin cells with a range current 0-50mah, voltage 0-5v. Each channel of the analyzer has independent constant-current and constant-voltage source, which can be programmed and controlled by computer software.
-
Product
CP-059-19 Battery Probes
Battery Probe
Current Rating (Amps): 10Average Probe Resistance (mOhm): 25Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 62Full Travel (mm): 1.57Recommended Travel (mil): 40Recommended Travel (mm): 1.02Mechanical Life (no of cyles): 100,000Overall Length (mil): 276Overall Length (mm): 7.01
-
Product
Automatic Batteries with Filters with Thyristors
BATLVFS600
-
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralized compensation of power factor in low voltage instalations.
-
Product
Battery Analyzers
CA 1550 – Military Version
-
*Portable Battery Charger / Analyzer.*0-25 Amp Charge.*0-50 Amp Discharge.*Fully adjustable.*115/230 Volt AC Input.
-
Product
Battery Test device
ATGB 1200
-
The ATGB 1200 is a battery tester for all standard battery technologies aimed at quality assurance, production and product development. Advantages of the ATGB: Creation of customized test sequences. Generation of load curves and peaks. Temperature measurement at the battery
-
Product
Battery Analyzers for Stationary Battery Systems
-
Fluke Battery Analyzers are the ideal test tool for maintaining, troubleshooting and performance testing individual stationary batteries and battery banks used in critical battery back-up applications in data centers, telecom networks, power distribution systems and more. With an intuitive user interface, a compact design, and rugged construction the Fluke Battery Analyzers are designed to provide optimum performance, test results and reliability.
-
Product
Resistance, Ground Testing, Battery And Power Quality
-
Our testing equipment works wherever you are, whenever you need it, with precision and reliability.
-
Product
Lead Acid Intelligent Battery Tester
612
-
This digital battery tester is designed for testing 6V and 12V standby SLA, cyclic GEL and car FLOODED batteries. Simple in operation, the ACT 612 simulates a full 20 hour (C20) discharge test in seconds and displays the DC Voltage results and Ah capacity available.
-
Product
Desktop Cell And Battery Testers
-
Maximize your testing capabilities with Maccor's hardware and software, conveniently packed into a compact desktop unit. Our comprehensive turn-key systems come bundled with all the essentials to jumpstart your testing process. Select from multiple options and configurations to match your requirements.Desktop testers can be configured with multi-current range channels that have an accuracy of ±30 ηA on the bottom range or single range channels configured to meet your needs. Contact Maccor for pricing and availability.
-
Product
Battery Simulator
-
The purpose of this battery impedance network (BNB) is to provide electric power to the device under test, providing a standard impedance. It has been developed for automotive tests. A resistor that emulates the internal battery resistance is implemented in the BNB.
-
-
Product
External Fire Exposure Test Machine, Battery Safety Testing
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBELL external fire exposure test machine is applicable to the standard UL 2580.
-
Product
Battery Monitoring System
S5
-
BTECH's benchmark product designed for a wide variety of applications (UPS/Telco/Switchgear), the S5 can collect data from any battery type including cells with the highest amp hour rating (4000+), and the S5 systems will record all battery parameters.
-
Product
Battery Test Chambers
-
At Weiss Technik we supply battery test chambers specific to testing batteries in a variety of conditions including low or high temperatures, humidity changes, vibration changes, and altitude changes. Our battery test chambers are designed to test Lithium Ion batteries, lead acid, Battery Managements Systems (BMS), battery packs, modules, battery cells, and more.
-
-
Product
Battery Charger/Discharger
BCD-3933T
-
Kongter Test & Measurement Co., Limited
Specially designed for single cell of 6V and 12V ONLY with max current of 50A. Three functions in one: charger, discharger and activator, which will facilitate your maintenance for batteries.
-
Product
Partial discharge measurement with remote wireless reading
PD-LT
-
The PD-LT allows online partial discharge detection on cable accessories such as cable head for safety and maintenance purposes.The PD-LT indicates the intensity of the partial discharges, converting the electrical charge units (pC) into decibels (dB). Thus the reading is kept as a simple intensity level indication, proportional to the probability of a fault's presence in the tested medium voltage accessory.The remote display gives a dB value of the probe's measurement. The dB value will vary along with the discharges indicators on the PD-LT probe. The measurement range is from 0 to 65dB and the display will show ''OL'' if the reading is over 65dB.
-
Product
Battery Capacity Tester
BLU-T Series
-
Battery load bank BLU-T is a powerful and lightweight solution designed for condition assessment of telecommunication and radio equipment backup supply. This instrument can perform the battery capacity test on battery strings such as Pb, Li-ion, Ni-Cd, and others. It tests battery strings with voltages in the range of 0,9 – 70,5 V DC. As a special feature, the BLU110T model enables capacity testing of single PB, Ni-based as well as Li cells (with current up to 100 A).The capacity test is conducted in an accurate, user-friendly way. Also, it is in accordance with battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22, and other relevant standards.BLU-T battery load bank enables setting the discharge current up to 350 A, with 0,1 A resolution. If higher currents are required, the BLU-T units can be connected in parallel, or BXL-T additional load units can be linked.The instrument offers a high power-to-weight ratio. BLU-T series has models starting from 12,8 kg / 28.2 lbs and up to 19,2 kW of power.A user can select one of three discharge modes: Constant current, Constant power, Constant resistance. Additionally, different battery duty cycles can be simulated using user-selectable discharge profiles.Discharge parameters can be monitored in real-time during the capacity test. A 4,3-inch touch screen shows overall battery voltage, discharge current, discharge test time and capacity during the entire test. Also, the capacity tester is compatible with DV-B Win software. A user can view a detailed numerical and graphical presentation of key parameters, and create reports in various formats.Testing can be carried out without disconnecting the battery from the service.
-
Product
Hybrid Vehicle Battery Simulator and Test System
-
Winner of the SAE 2008 Technical Award for Hybrid Vehicle Testing Technology, SAKOR Technologies Hybrid Vehicle Battery Simulator and Test System is designed for simulating high-voltage batteries in an electric drivetrain testing environment as well as directly testing high-voltage batteries and charging systems.
-
Product
Automatic Battery with Filters with Standard Contactors
BATLVF400
-
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralized compensation of powerfactor in low voltage instalations
-
Product
BATTERY PACK AND BMSTEST SYSTEMS
-
DMC's Battery Pack Test Systems facilitate battery design as well as research and development for national laboratories and research institutions. They are deployed in end of line / production test stations for battery packs developed by major automotive manufacturers and their suppliers. DMC's battery pack test systems are designed to evaluate the battery as a complete system and validate a comprehensive range of battery pack functionalities, including:Power performance, Capacity, DCR / Internal ResistanceContactor and safety interlock functionsIsolation / Insulation ResistancesReporting of operating data through external communication interfaces (usually CAN)Cell VoltagesPack / Cell TemperaturesState of ChargeFaults / Diagnostic Trouble Codes (DTCs)Etc.Electrical characteristics / continuity of internal pack wiring / signalsCooling system operation
-
Product
Continuity Tester Supplied without Battery
22700
-
Use to test for continuity with power disconnected. Excellent for use on marine, recreational and general automotive vehicles. Test appliances and other electrical circuits with power off. 48" lead wire. Uses AA 1.5 volt battery (not supplied).
-
Product
High Current Probes for EV Battery Packs
High Current Probe
Up to 500Amps - customized connections - battery pack charging.
-
Product
Battery Testing
-
Electric vehicles (EVs) rely on batteries as their primary source of energy storage. As battery packs require battery management systems (BMS) to operate safely and reliably, it is vital to test control algorithms for state of charge (SoC) estimation or cell balancing at an early stage.
-
Product
Battery (EV) Automatic Test System
-
Landrex Technologies Co., Ltd.
Battery (EV) Automatic Test System
-
Product
Battery Maintenance & Test Equipment
-
Fuzhou Fuguang Electronics Co., Ltd.
Battery Maintenance & Test Equipment
-
Product
Glow Discharge Atomic Emission Spectrometer
GDS900
-
LECO's Glow Discharge Spectrometer (GDS) offers you state-of-the-art technology designed specifically for routine elemental determination in most conductive ferrous and nonferrous materials. The GDS900 features improved performance, stability, accuracy, and precision in steel, iron (including as-cast), aluminum, copper, zinc, nickel, cobalt, tungsten, and titanium materials, while featuring our user-friendly Cornerstone® brand software to help streamline your analysis.
-
Product
Advanced Battery Conductance/Electrical System Tester
PBT Series
-
Building upon the success of the PBT-100, the first battery conductance tester built for the professional technician's toolbox, the PBT-200 offers these additional capabilities: Shows available power in CCA in addition to condition and voltage. Bad Cell Detection. Advanced Starter Testing: Down arrow displays the captured low voltage from cranking the engine for simple starter analysis.
