Loop a Line
-
Product
Transmission Line Probes
-
Transmission line probes are a special type of passive probe designed for use at very high frequencies. They replace the high impedance probe cable found in a traditional passive probe with a precision transmission line, with a characteristic impedance that matches the oscilloscope input (50 Ohm). This greatly reduces the input capacitance to a fraction of a picofarad, minimizing the loading of high frequency signals. A matching network at the tip increases the DC input resistance. While they have lower DC input resistance than a traditional passive probe (usually 500 Ohm) to 1kOhm), the input impedance of these probes remains nearly constant over their entire frequency range. A traditional /10 passive probe will have a 10 MOhm) input impedance at DC, however this impedance drops rapidly with frequency, passing below the input impedance of a transmission line probe at less than 100 MHz.
-
Product
Line Scan Sensors
-
The CMOS line scan image sensor family from ams consists of 23 variants, offering a range of resolution and pixel size specifications. Resolution options range from 2kpixels up to 16kpixels and line rates extend up to 80,000 lines/s.
-
Product
Line Leakage Tester
LineCHECK II
-
Designed for Automated Test ApplicationsFull Compliment of Automation InterfacesComplete Line Leakage Testing SolutionEnhanced Graphic LCDCompatible with Scanning Matrix for Patient Lead TestingContinuous Run FeatureSoftware CompatibleSafety Agency Listed
-
Product
PXI/PXIe Analog Output/Current Loop Simulator Module - 4 Channel
43-765-004
Analog Output Module
The 41/43-765-004 is an 4-channel Analog Output Module designed to meet the requirements of industrial control applications utilising current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signalling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
Product
Wafer Auto Line Integration
-
The line is used for semiconductor wafer grinding. It carries out material matching and distribution, automatic loading and unloading, auto focusing and positioning and many other functions. The grinding precision is 2μm(3-sigma). It is also capable of collecting and analyzing real-time production data and interfacing with MES system.
-
-
Product
Test Line • Perforation counter
Perforation counter PZ 3
-
The perforation counter PZ 3 can be used among other things in the production of plastic bags and garbage bags. By the non-contact perforation detection, for example, the number of bags / batches can be determined and the roll change can be initiated.
-
Product
Level Control Loop Trainer Model
ULP-24P & ULP-24C
-
Unitech Scales And Measurements Pvt. Ltd
Unitech’s Level Control Setup comprises of acrylic measuring tank fitted with Level transmitter, control valve, I to P converter, source tank with water pump and necessary flexible piping for water circulation. The system is mounted on a table top powder coated metal frame. Level transmitter is of capacitance or DPT type sensor. The electronic panel comprises of ADC and DAC card with RS-232 interfaces.
-
Product
Fault Passage Indicator for Lines
LineTroll R400D
-
LineTroll R400D Fault Indicator indicates earth- and short-circuit faults and can distinguish between permanent and transient faults. The indicator has two sensors and use both the electrical field and the magnetical field to detect faults on all three phases.
-
Product
Vehicle Inspect Lines Software System
-
Foshan Analytical Instrument Co, Ltd.
Flexible control mode(A collective-type control mode can be adopted,but a distributive-type control can also be adopted);Powerful system function(Distributive-type control and collective-type management,provide the functions of equipment debugging,vehicle log-in,vehicle testing and bill printing.A secret code and right-limit can be set so that the system safety function is enhanced);Remote control(A remote log-in,main remote control and remote printing can be realized in accordance with the actual conditions of the testing station.At the sametime,provides a powerful data-base and one station with multi-wire:That is one testing station has more
-
Product
In Line Load Cell (200N-5000N)
100 Series
-
Miniature Threaded in Line Load Cells are strain gage based transducers with temperature compensation and excellent overall performance. This type measures tensile and compressive loads up to 5000N with better than ±0.25% non-linearity.
-
Product
Closed Loop Hall Effect Current Sensors/Transducers
-
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on closed loop compensating principle and can be used for measurement of DC and AC current, pulse currents etc. The output of the transducer reflects the real wave of the current carrying conductor
-
Product
USB Line Scan Camera
TinyUSB
-
*Very small and compact dimensions, only 40 x 30 mm²*High speed, up to 9kHz line rate*Programmable amplifier and offset*Supported operating systems:****Windows**Linux**Linux ARM32 (Raspberry PI)
-
Product
Precision Line Gage
PLG100
-
The PLG100 Precision Line Gage system is specially designed for desktop use in order to measure conductor line widths, conductor line spaces, arcs, circles and other patterns on the PCB. It can measure a conductor line width less than 1 mil. The PLG100 system is unbelievably light weighing only 0.73 kg and providing easy mobility
-
Product
High-Resolution Line Camera
X-Scan F
-
High-resolution line cameras for accurate and fast-paced quality inspection, and the grading and sorting of raw materials.
-
Product
Quad Op-Amp Loop
QOAL400
-
The QOAL400 module is a precision instrument capable of measuring all common parameters of an Op Amp, including AC as well as DC parameters. The QOAL400 has four completely independent channels, which allow a quad device to be tested in a minimum amount of time. Each channel has a full set of resources to measure all common parameters.
-
Product
Resistance Bridges - AccuBridge® Line
-
Measurements International Ltd.
The Resistance Ratio Bridge from Measurements International is the next generation replacement. Measurements International is pleased to release the next generation room temperature Direct Current Comparator Resistance Ratio Bridge.
-
Product
3 GHz, 4 Channel Programmable Delay Line
QPADL3
-
The QPADL3 is a programmable delay line instrument with 4 independent channels designed for adjusting the time delay or phase of radio, microwave or even digital signals with bandwidths from DC to 3 GHz.
-
Product
Line Post Sensors
-
These products are designed for distribution circuits only at their rated capacities. They cannot be field modified for capacities other than what was shipped with the units.
-
Product
10 Gb/s Programmable Digital Delay Line
PDDL10
-
The PDDL10 is a precision time delay generator for digital signals. Delays are controlled precisely in 5 increments from 0 to 635 ps.. Data rates through 10 gigabits per second are supported for very high-speed applications. Delays can be programmed via a TTL bus.
-
Product
Guidance Laser with Remote In-Cab Line Adjust
GL3000P
-
The GL3000P Guidance Laser uses an ultra high visibility green laser to establish visual line control for the vehicle driver. Used for highway paint striping, asphalt distributors, road wideners, pavement profilers, or virtually any application requiring vehicle line control. GL3000P model is for truck cab mounting.
-
Product
Air Core Line & Load Reactors
-
Line and load reactors are generally serial-connected to the input and/or output terminals of three phase equipment such as motor speed controllers, inverters and UPS systems. These equipment make use of semiconductor switches such as IGBTs, thyristors, and diodes and therefore create harmonic distortion and high switching over-voltages (dv/dt). Use of such equipment has been becoming more widespread as the technology advances. However, the negative effects of these equipment should not be overlooked.
-
Product
Programmable Delay Line Instrument
XR-100
-
The XR-100 is designed to give you our broadest signal delay range as well as superior switching speeds
-
Product
RS-232, RS-422, or RS-485 to Fiber Optic Line Driver
Model 8277
-
The Model 8277 is a unique asynchronous fiber optic modem whose optical interface can operate in either point to point or ring (daisy chain) configurations and whose electrical interface can also operate in point to point or multi-drop configurations depending on the user selected interface.
-
Product
DUAL-IN-LINE (DIL/DIP) SERIES 97 - 98
-
Pickering’s dual-in-line (DIP/DIL) reed relays are through-hole electronic components that enclose two parallel rows of connection pins on the standard DIL spacing with switching capability up to 2 Amps, 50 Watts. The reed relays come with 5, 12 or 24 V coils with or without internal diode. Many standard build options are available on request, or we can fully customise the parts to suit your exact specifications.It is often possible to replace TTL ICs with their equivalent CMOS ones and replace standard DIL relays with Pickering Series 98, to obtain the benefits of CMOS without any circuit or PCB redesign.
-
Product
End-of-Line IC & MEMS Tester
igentic® 841t
-
Integrated circuit (IC) and micro electro-mechanical system (MEMS) device manufacturers need to address the challenges of today's global market including increased functionality, speed and complexity while delivering components at reduced costs. Sterner Automation's igentic® 841t automated test systems meet these demanding requirements by providing a flexible platform for comprehensive end-of-line IC and MEMS device handling, testing, grading and packaging. The resulting improvements in quality assurance and process efficiency will maximize customer satisfaction and profitability.
-
Product
Optical Coherence Tomography Imaging Line Scan Cameras
OctoPlus Range
-
Teledyne e2v spent 2 years developing a CMOS sensor specifically for OCT. This resulted in the launch of OctoPlus, which has a specially designed pixel architecture that improves sensitivity and reduces signal roll-off to improve image quality by several dB vs state-of-the-art CMOS cameras, especially in deep structures.
-
Product
16 Port Analog Phone Line (FXS)
SIM-16FXS
-
This unit has 16 analog phone lines (FXS) making it a perfect tool for testing VoIP gateways, IVR, modems, access servers, audio conference equipment or anything that requires phone lines. Telephone line simulator acts like a "telephone company in a box" providing dial tone, ring voltage and all advanced phone line features such Caller ID, Call Waiting, Call Hold, Three Way Calling and many others.
-
Product
AC Power Line EMI Filters
CleanSweep®
-
CleanSweep® filters block EMI on power lines (both common and differential modes) and, uniquely, in ground, from reaching sensitive equipment. They also reduce EMI "backflow" from a "noisy" source that otherwise would end up on your AC power network.
-
Product
Line Scan Cameras
-
The highly sensitive Basler monochrome and color line scan cameras are suitable for applications that require high throughput and image quality. Quality assurance is essential in battery production.
