Filter Results By:
Products
Applications
Manufacturers
LIN
Local Interconnect Network
See Also: Serial, I2C, Can bus, ExpressCard, Fieldbus, FireWire, RS-232, RS-485, PCI Express, Serial ATA, Serial Peripheral Interface, SMBus, CAN, LAN
-
product
NI CAN Cable, No Term, High-Speed/FD/Low-Speed, D-Sub 9-Pin F, 1m
193128-01
9-Pin Female D-SUB to 9-Pin Female D-SUB CAN Cable - The DB9F-DB9F CAN Cable connects C Series CAN Interface Modules, C Series LIN Interface Modules, or C Series Multiprotocol Interface Modules to devices, breakout boxes, and accessories. It is sometimes referred to as CAN Cable (single termination or no termination). This cable is compatible with high-speed, flexible data-rate, and low-speed/fault tolerant CAN signals, available with or without termination, and in different lengths.
-
product
Vehicle Multiprotocol Interface Module
C Series
C Series Vehicle Multiprotocol Interface Modules use hardware-selectable NI-XNET Transceiver Cables (TRC) to communicate High-Speed/Flexible Data‑Rate CAN, Low-Speed/Fault Tolerant CAN, and/or LIN. Using the NI-XNET driver, you can create applications that require real-time, high-speed manipulation of hundreds of CAN and/or LIN frames and signals. The NI-XNET device-driven DMA engine enables the onboard processor to move frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time. C Series Vehicle Multiprotocol Interface Modules work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
product
sbRIO-9860, Non-Enclosed, 2-Port, C Series Vehicle Multiprotocol Interface Module
787325-01
Non-Enclosed, 2-Port, C Series Vehicle Multiprotocol Interface Module - The sbRIO-9860 is a hardware-selectable HS/FD controller area network (CAN) and/or local interconnect network (LIN) interface for developing CAN and/or LIN applications. As part of the NI-XNET product line, the sbRIO-9860 works well for applications requiring high-speed manipulation of hundreds of frames and signals while performing low-level FPGA control and embedded monitoring in the same CompactRIO Single‐Board Controller. Non-enclosed modules are available for OEM applications.
-
product
Network Analyser And Diagnostics
Module Analyser
Module Analyser is a 5 in 1 easy to use CAN bus analyser with the following advantages:■ CAN and LIN monitoring via DBC/LDF/Fibex files ■ Automotive OBD ISO15765 Scan tool and UDS ISO14229■ J1939■ Integrated ODX/MDX editor■ Data acquisition and logging
-
product
InfiniiVision Oscilloscopes
2000 X-Series
70 MHz to 200 MHz See more signal detail with 50,000 wfms/s update rateView time-correlated digital content with 8 digital channels (MSO)Modulate signals within the scope with WaveGen, built-in 20 MHz function generator (optional)Quickly characterize signals with the built-in 3-digit voltmeter and 5-digit counter option Decode serial busses faster with hardware-based serial analysis options for CAN, LIN, I2C, SPI and RS232/422/485/UART Protect your investment with full upgradability
-
product
PXIe-8510, 6-Port PXI Vehicle Multiprotocol Interface Module
784122-01
2- or 6-Port PXI Vehicle Multiprotocol Interface Module—The PXIe‑8510 is a hardware-selectable controller area network (CAN) and/or local interconnect network (LIN) interface for developing applications with the NI‑XNET driver. The PXIe-8510 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
product
Advanced Platforms
TTConnect 616
TTConnect 616 is an advanced connectivity platform that combines and manages all in-vehicle interfaces such as CAN-FD, Flexray, LIN and Ethernet. Its wealth of interfaces is complemented by advanced traffic management software and support for Time Sensitive Networking protocols, making TTConnect 616 the ideal solution for future-proof vehicle architectures where different types of traffic must converge and operate in a safe and reliable manner.
-
product
PXI LIN Interface Module
The PXI LIN Interface Module is a bus interface for developing applications with the NI-XNET driver. The NI-XNET device-driven DMA engine couples the LIN bus to host memory to minimize message latency. You can import, edit, and use signals from LIN Description File (LDF) databases in integrated LIN databases. PXI LIN Interface Modules work well for applications requiring real-time, high-speed manipulation of many LIN frames and signals, such as hardware-in-the-loop simulation, rapid control prototyping, bus monitoring, and automation control.
-
product
CAN, CANopen, J1939 Tester
X-Analyser3
Warwick Control Technologies Ltd.
Graphical User Interface ideal for Windows PCs and tablets.• CAN, J1939, NMEA2000, CANopen, LIN and OBD – included into one tool• On-Board Diagnostics Scan Tool Features for Emissions ECUs.• CAN and LIN signal reverse engineering• Signals displays – text, scope and graphical such as gauges and lamps• Can be used for ECU or even network simulation• SAE J1939 database integrated with over 4000 PGNs and signals
-
product
PXIe-8510, 2-Port PXI Vehicle Multiprotocol Interface Module
784121-01
2- or 6-Port PXI Vehicle Multiprotocol Interface Module—The PXIe‑8510 is a hardware-selectable controller area network (CAN) and/or local interconnect network (LIN) interface for developing applications with the NI‑XNET driver. The PXIe-8510 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
product
The all-in-one data logger for the entire vehicle networking
PM-200
The PM-200 sets the bar considerably higher on the topic of safeguarding and troubleshooting vehicles. Bus systems such as CAN, CAN-FD, FlexRay™, LIN, MOST150 and Automotive Ethernet are logged at a data speed up of to 120 MB/s. SSD removable media allow for quick evaluation and distribution of the data. Various upgrade options enable configuration for any application. Flexibility, programmability and support from debugging protocols make it possible to meet the high demands of functionality and fleet tests as well as of test runs.
-
product
NI CAN Cable, No Term, High-Speed/FD/Low-Speed, D-Sub 9-Pin F, 2m
193128-02
9-Pin Female D-SUB to 9-Pin Female D-SUB CAN Cable - The DB9F-DB9F CAN Cable connects C Series CAN Interface Modules, C Series LIN Interface Modules, or C Series Multiprotocol Interface Modules to devices, breakout boxes, and accessories. It is sometimes referred to as CAN Cable (single termination or no termination). This cable is compatible with high-speed, flexible data-rate, and low-speed/fault tolerant CAN signals, available with or without termination, and in different lengths.
-
product
LIN Interface Module
C Series LIN
C Series LIN Interface Modules are bus interfaces for developing applications with the NI-XNET driver. The NI-XNET device-driven DMA engine couples the LIN bus to host memory to minimize message latency. You can import, edit, and use signals from LDF databases in integrated LIN databases. C Series LIN Interface Modules work well for applications requiring real-time, high-speed manipulation of many LIN frames and signals, such as hardware-in-the-loop simulation, rapid control prototyping, bus monitoring, and automation control.
-
product
NI-9860, 2-Port, C Series Vehicle Multiprotocol Interface Module
783703-03
2-Port, C Series Vehicle Multiprotocol Interface Module - The NI‑9860 is a hardware-selectable HS/FD controller area network (CAN) and/or local interconnect network (LIN) interface for developing CAN and/or LIN applications. As part of the NI‑XNET platform, the NI‑9860 works well for applications requiring high-speed manipulation of hundreds of frames and signals while taking other data acquisition measurements in the same CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same CompactRIO chassis.
-
product
Logic Analyzer & Digital Pattern Generator
ScanaQuad Series
ScanaQuad (SQ) is a series of high performance 4 channels logic analyzers and digital pattern generators. They are designed to be your best companion when working on serial protocols like UART, SPI, I2C, 1-Wire, USB, I2S, CAN, LIN, RS232, RS485, and more. With ScanaQuad Logic Analyzers, you can capture signals, you can play them back, and you can even build genuine test signals and generate them!
-
product
CAN/LIN Communications Expansion Kit
OP-SB7GX
OP-SB7GX is the expansion kit which makes it possible to monitor, and simulate CAN and LIN communications. It enables monitoring of CAN and LIN data in any combination up to 2 channels at a time. Suitable for evaluation of mixed in-vehicle networks of CAN and LIN.
-
product
Universal Analysis Tool
CANalyzer
CANalyzer is the universal analysis tool for ECU networks and distributed systems. CANalyzer makes it easy to observe, analyze, and supplement data traffic in CAN, LIN, MOST, or FlexRay systems. With powerful functions and user-programmability, all needs are covered from simple network analysis to advanced troubleshooting of complex problems.
-
product
PXI-8516, 2-Port PXI LIN Interface Module
781366-01
2-Port PXI LIN Interface Module—The PXI‑8516 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver.The PXI‑8516 excels in applications requiring real-time, high-speed manipulation of hundreds of LIN frames and signals, such as hardware-in-the-loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move LIN frames and signals between the interface and the user program without CPU interrupts, minimize message latency, and free host processor time for processing complex models and applications.
-
product
10MHz DDS Function Generator With Counter
TG1006
0.001Hz to 10MHz frequency range6 digits or 1mHz resolution1ppm stability and 10ppm one year accuracyLow distortion, high spectral purity sine wavesInternal phase continuous sweep, lin or logUnique manual sweep gives quasi-analogue controlAM and FSK modes, frequency list (10 steps)2mV to 20V pk-pk from 50 or 600 OhmsBuilt-in seven digit 120MHz frequency counterLow cost
-
product
3U CompactPCI Serial Vector FlexRay CAN LIN Module Carrier
SFV-RAY
The SFV-RAY is a 3U CompactPCI Serial carrier card for the Vector VN7610 and similar Vector FlexRay/CAN-FD compact interfaces. On-board USB controller. Can be installed in any peripheral slot of a CPCI Serial backplane.
-
product
Line Monitor
LE-170SA
LE-170SA is a compact hand-held size line monitor for CAN/LIN. It has a touch screen and can be control as for smartfones. It has 1 CAN channel and 1 LIN channel and it can monitor both CAN and LIN communication thus monitoring of the network which has both CAN and LIN is available. The monitor function can diplay the communication data in real-time while saving it. The simulation function can send/receive the test data instead of the original communication partner. The ID filtering and trigger function make your development/evaluation more efficient. It also can measure 4 external signals as degital signals or analog signals while monitoring the communication data.It is light (300g) and convenient for field testing. The line monitor is useful for not only development but also maintenance.
-
product
Test Slave For The LIN Bus With Various I/Os
PLIN slave
The PLIN slave is an evaluation board with an interface for a LIN 2.0 bus. The device also offers comprehensive I/O functionality, which is accessible via operating and display elements.
-
product
CAN & LIN bus Custom Test & Simulation Software
CanX
Schleissheimer Soft- und Hardwareentwicklung GmbH
CanX is the custom testing and simulation software for CAN and LIN bus for specific user groups. The run-time software is designed to execute predefined or automated tasks in testing, work preparation, production, repair or project management.
-
product
NI CAN No Termination Cable w/Power Terminals, HS/FD/LS, 1m
782578-01
9-Pin Female D-SUB With 2-Pin Female Power Screw Terminal to 9-Pin Female D-SUB CAN Cable - The DB9F-PT2F-DB9F CAN Cable, sometimes referred to as CAN Cable (with power terminals), connects C Series CAN Interface Modules, C Series LIN Interface Modules, or C Series Multiprotoco Interface Modules that have ports requiring external power with external CAN signals. The screw terminals on the cable allow for the direct wiring of power and ground to the port on the CAN interface. This cable is compatible with high-speed, flexible data-rate, and low-speed/fault tolerant CAN signals and is available with or without termination.
-
product
USB-8506, 1-Port, USB LIN Interface Device
784663-01
1- or 2-Port, USB LIN Interface Device—The USB‑8506 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver. The USB‑8506 is powered over the USB bus and does not require external power. The USB‑8506 excels in applications requiring logging or manipulation of hundreds of LIN frames and signals, such as in-vehicle data logging, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move LIN frames and signals between the interface and the user program without CPU interrupts, minimize message latency, and free host processor time. The USB‑8506 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
product
DDS Function Generator, Digital Control 10MHz Or 20MHz, With/without USB/RS232 Interfaces
TG2000 Series
0.001Hz to 10MHz/20MHz frequency range6 digits or 1mHz resolution1ppm stability and 10ppm one year accuracyLow distortion, high spectral purity sine wavesInternal phase continuous sweep, lin or logAM, FSK, gated and tone switching modes5mV to 20V pk-pk from 50 or 600 OhmsStorage for multiple instrument set-upsUSB and RS232 Interfaces (TG2000 only)
-
product
sbRIO-9866, Non-Enclosed, 1-Port C Series LIN Interface Module
785965-01
Non-Enclosed, 1-Port C Series LIN Interface Module—The sbRIO‑9866 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver. The sbRIO‑9866 excels in applications requiring real-time, high-speed manipulation of hundreds of LIN frames and signals such as hardware‑in‑the‑loop (HIL) simulation, rapid control prototyping, bus monitoring, automation control, and more. You can perform this manipulation while taking other DAQ measurements in the same CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same CompactRIO Chassis. Non-enclosed modules are designed for OEM applications.
-
product
CAN/LIN Instrument
Each 5-channel CAN and 5-channel LIN can be independently controlled for simultaneous operation. It is an intelligent instrument which uses its own on-board processor to send/receive/compare Controller Area Network (CAN) and Local Interconnect Network (LIN) messages.
-
product
NI CAN Single Termination Cable w/Power Terminals, HS/FD, 2m
782579-02
9-Pin Female D-SUB With 2-Pin Female Power Screw Terminal to 9-Pin Female D-SUB CAN Cable - The DB9F-PT2F-DB9F CAN Cable, sometimes referred to as CAN Cable (with power terminals), connects C Series CAN Interface Modules, C Series LIN Interface Modules, or C Series Multiprotocol Interface Modules that have ports requiring external power with external CAN signals. The screw terminals on the cable allow for the direct wiring of power and ground to the port on the CAN interface. This cable is compatible with high-speed, flexible data-rate, and low-speed/fault tolerant CAN signals and is available with or without termination.
-
product
CAN/LIN Communications Expansion Kit
OP-SB87
OP-SB87 is an expansion board for CAN/LIN communications, inserting into a slot of communication analyzer LE-8200A/LE-8200. It has 2 CAN connectors and 2 LIN connectors, and measures 2 channels of CAN or LIN, or 1 CAN/1 LIN. It is useful to measure network where there are CAN and LIN communications at the same time.
