AC DC Electronic Loads
-
Product
AC Voltage Monitors
Voltage Monitor
NAI's AC- and DC-powered AC voltage monitors are used to monitor and measure voltage characteristics of single- and three-phase power lines. Field-adjustable AC voltage monitors are also available. These monitors are specifically designed for rugged defense and industrial applications.
-
Product
Electronic Loads
Series EL
-
The EL Series is a line of modular aircooled, DC electronic loads used to test power sources such as batteries, power supplies, generators, chargers, fuel cells, etc.Power ratings start at 1KW; standard models have maximum test capabilities of 50, 200, 400 and 600 volts. High current and power operation are achieved via parallel connection in a master/slave configuration. Individual modules are capable of up to 5KW and 800 amperes.
-
Product
4 Phase MICRO~Flex AC Current Probe
DRM 504/4
-
The new DRM 504/4 is a 4 Phase MICRO~flex AC current Probe utilising the Rogowski principle, with 4 channel integrator housed in DIN Rail Mounted Enclosure. The flexible and lightweight measuring head allows quick and easy installation in hard to reach areas and with large conductors.
-
Product
SCR CONTROLLED VARIABLE DC POWER SUPPLY
P5085C
-
Shown below is an AC to DC power supply with 4/20 ma interface. Input is 240 VAC, 1 PH, 60 Hz. Output is 0 to 10.5 DC, 130 Amps. This power supply can be interfaced to a PLC system. These units are customized units, built to order.
-
Product
Hand-Held Alternator/Battery Load Tester
6024
-
• Full 125 Amp load tests 12 Volt and 24 Volt Batteries, alternators and starters on all types of vehicles• PATENTED• Made in USA of US and Global Components
-
Product
COMMON RAIL Electronic Diesel Injection Analyzer
EDIA-PRO
-
The EDIA-PRO is an enhanced version of the proven EDIA-5 analyzer. To meet expectations of our customers we created a system for automatic evaluation of injection system parameters based on measured waveforms. This makes the diagnosis easier and faster. Additional possibility of fast evaluation of cylinder compression and ability to check starting performance along with control valve measurement mode are perfect complement to diagnostic capabilities of EDIA device.
-
Product
Through Hole Type AC Current Sensor
CTF-400B
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*For AC current and power measurements.*Suitable for current measurements of main cable.*Measuring range:AC 1A～400A.
-
Product
Compression Load Cells
-
A block that is designed to hold a load at one point to measure the compression. While tension load cells measure the pulling force, compression load cells measure a pushing force along a single axis.
-
Product
Programmable AC Power Source
Model 8600 Series
-
- Compact size and light weight, standard 19″ rack construction- Step-less frequency setting from 45 to 450Hz- Very low distortion sine wave output- Output voltage range selectable 135 or 270V AC- Galvanically isolated input/output- Independent on/off switch for input and output- 16×2 vacuum florescent display for parameter display- Complete operation through push switches and a digital rotary encoder- Automatic protection against overload, short circuit and over temp.- Built in PFC to provide 0.99 input power factor and wide input range- Conforms to EN55022, class A, safety standard EN60950
-
Product
Coaxial Fixed Attenuator, DC to 67 GHz
8490G
Attenuator
Keysight's 8490G precision coaxial fixed attenuators maximize your operating frequency range up to 67 GHz by providing industry-leading attenuation accuracy, coupled with low SWR and a variety of attenuation options to suit your application needs. The attenuator is available in attenuations of 3, 6, 10, 20, 30 and 40 dB. The 8490G is swept-frequency tested to ensure it meets specifications at all frequencies.
-
Product
EQCM Electronic Quartz Crystal Microbalance
Elettra
-
Elettra has been designed to operate on its own, but it is also possible to connect it to a PC to control it and acquire, view and save data thanks to its extremely easy to use software that runs under MS-Windows™. The data acquisition process can be controlled extremely quickly thanks to the PLAY, PAUSE and STOP keys.
-
Product
DC Power Supply
DC Power Supply
DC power supplies offer many unique advantages for telecom, automated test system & integration, industrial, battery charge & simulation for hybrid cars and solar panel simulation. These advantages include high power density of 15KW in 3U, precision readback of output current and voltage, output trigger signals as well as the ability to create complex DC transient waveforms to test device behavior for spikes, drops, and other voltage deviations.
-
Product
Adjustable AC Power Meter
APS-6000
-
The APS-6000 adjustable AC power source is a multi-function AC power source that integrates voltage, current, power and power factors. The internal high-speed processor is a cost-effective, high-stability AC power source.
-
Product
Ultra Low Level DC Voltage Amplifiers
-
The EM A10 is a low level amplifier module for sensitive measurements, data collection and systems, where signals below 1 nanovolt may be measured. It is ideal for the input unit for precision voltage measuring systems, requiring voltage sensitivity for measuring low noise and low impedance sources. The noise level of the A10 is equivalent to a perfect resistor of about 20 ohms. When used with a digital voltmeter, steady one nanovolt digits may be displayed, with a response time constant of less than a second. The input voltage stability of the A10 is very high, with the drift around a nanovolt per degree C. The input connectors are made from pure copper. The input impedance is very high, and is time dependent, determined by the loop gain.
-
Product
Programmable Bidirectional AC Laboratory Power Supplies (source / Sink)
-
Programmable Bidirectional AC Laboratory Power Supplies (source / Sink)
-
Product
DC toDC Converters
-
Low Cost Single Dual and Triple outputs Isolated Outputs Low Ripple, Regulated Outputs Standard packages and pin outs Custom Designs availableNew Miniature V3 Series features HighVoltage Isolation, SIP and DIP packages
-
Product
UHVDC(Untro High Voltage DC) Testing
-
In the super (ultra) high-voltage transmission field, UHVDC converter stations are mainly composed of three parts: AC system, valve system, and DC system. Each part consists of primary and secondary electrical equipment. PONOVO, relying on its core technology, extensive system testing experience and high-efficiency production capabilities, have continuously explored super (ultra) high-voltage test technologies, and nearly 10 types of test equipment have been developed for converter system substations and system debugging.
-
Product
DC Blocking Power Splitter Combiner
PD7020
-
INSTOCK Wireless Components, Inc
Wideband Frequency, 698-2700 MHzLow Insertion Loss (0.2 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)50 VDC maximum on DC block portTri Alloy Type-N Female (Jack) Low PIM
-
Product
Single-Channel DC Powered Carrier Demodulator
CD16
-
The CD16 Miniature Carrier Demodulator is designed to deliver a 0 to 5 Vdc output from a variable reluctance transducer and operate from unregulated 9 to 55 Vdc power. A square wave excitation of 5 kHz is furnished to the transducer and the solid state integrated circuit amplifier and demodulator converts the transducer signal to an analog dc output. Zero and Span adjustments are made through access holes in the case.
-
Product
Attenuators & Loads
-
*High power handling 100W with a wide range of available attenuation values*Very low PIM <- 160 dBc with excellent return loss performance*Support for 7-16 or 4.3-10 connectors and optional 19 inch rack mount kit*Designed and produced to ISO 9001:2008 certification standards for reliability and quality
-
Product
Bolt Extensometers for Proof Load Testing
Model 3565
-
Jinan Testing Equipment IE Corporation
The Model 3565 uses hard conical points to contact the bolt at the center of the head and at the bottom. It is fully adjustable for different length bolts ranging from 25 mm (1 inch) in length to 150 mm (6 inches) standard. Extension beams are available for longer bolts. The standard maximum measuring range is 1.25 mm (0.05 inches). Generally, on longer bolts this extensometer will be self-supported without requiring any centering marks or punch marks on the bolt. For shorter bolts these marks may be required. If the conical pins are sharp, marks are often not needed even on the shortest bolts.The extensometer has a zero adjustment screw to adjust the length between the contact pins. This is used to set the output voltage to zero, which corresponds to the correct starting position for the test. It also includes a breakaway lower arm. In the event a bolt should fail, the breakaway arm snaps free, helping to prevent damage to the extensometer. This is easily re-installed. In the event that bolt failures are likely during a test, it is recommended the user attach a cord around the upper part of the beam and tie the other end to the test frame to prevent the extensometer from falling. The conical point contacts included with the extensometer are made from tungsten carbide.The Model 3565 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
Product
4 Way GPS / GNSS Signal Splitter Passive, 1-2 GHz, SMA, DC Block+200Ω Load 4 Ports
GPS412
-
INSTOCK Wireless Components, Inc
GPS L1 - L5, GLONASS, Galileo splitterLow Insertion Loss (0.4 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)15 VDC & 75 mA max on DC block portsTri Alloy SMA Female (Jack) 50 Ohm
-
Product
Clamp Meter, Auto, True RMS, 400 A AC, 600 V AC, 600 V DC, 28 mm Jaw Opening Max.
72-7226 CAL DU
-
The 72-7226 CAL DU from Tenma is a digital clamp meter. This stable, safe and reliable digital clamp multimeter is designed with large scale integrated circuits and A/D converter as the core as well as overload protection and novel structure which make them a superb tool for electricians. It measures AC/DC voltage, AC/DC current, frequency, duty cycle, resistance, diodes and continuity and also includes data hold, sleep mode and relative mode features. The resistance measurement range from 400 ohm/4kohm/40Kohm/400Kohm/4Mohm/40Mohm (±(1%+2)), frequency measurement range from 10Hz to 10MHz (±(0.1%+3) accuracy). It is 3 3/4 digit digital clamp meter with precise operation, fashionable structure and highly reliable measuring instrument. The meter uses large scale of integrated circuit with double integrated A/D converter as its core and has full range overload protection. It complies with IEC61010, pollution degree 2, overvoltage category (CAT II 600V, CAT III 300V) and double insulation.
-
Product
Load Cell Transmitter
MODEL SST-HV
-
The SST-HV is a Plug & Play Smart TEDS IEEE 1451.4 compliant Transmitter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the SST-HV will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the SST-LV Transmitter is easily programmed using a PC with an RS232 port and Instrument Setup (IS) software, which provides a graphical user interface. The SST-HV may be powered from 95-240 Vac ±10%. The SST-HV has an Isolated transducer excitation output that is selectable between 5Vdc or 10Vdc. There are Dual solid state relays and an Isolated 4-20 mA, 0-20 mA or 0-10V analog output. There are three Isolated serial data transmitter output ( RS232 , Half-duplex RS485, full-duplex RS485 ) and three serial protocols that are software selectable (Modbus RTU, Modbus ASCII and Custom ASCII). Isolation to 250V rms is provided for power, signal input, analog output, relay outputs, and communications. Isolation adds safety and avoids possible ground loops. The transducer excitation output is isolated to 50V from signal ground.
-
Product
AC Control Time Switch
IM1756
-
Ajinkya Electronic Systems offers AC and water cooler controller, an energy saving device for controller air conditioner unit and water cooler optimally to save Electricity. AC Control Time Switch offers unparallel features to not only save energy but to save compressor from electrical voltage and overload.
-
Product
Industrial Electronics Testing for Smart Devices & More
-
As more and more devices are being designed with inherent intelligence and the ability to connect and communicate, the amount and complexity of electronic content is continuously increasing for our industrial customers. They need the ability to quickly and efficiently verify proper operation of these products as they flow off the production line. Circuit Check responds to these needs by offering a wide range of industrial electronics testing solutions from consulting to complete test system and software design. We also offer adaptable support solutions to ensure proper equipment operation throughout its life cycle.
-
Product
AC to AC Programmable Power Sources
AFV-P Series
-
Rating:600 VA to 5 KVASingle Phase OutputOutput frequency: 45 Hz to 500 Hz (Optional for 15 Hz to 1000 Hz)
-
Product
DC Hysteresis Graph
DX-2012SD
-
Automatic measurement on basic magnetization curve and magnetic hysteresis loop under static state of soft magnetic material, accurate measurement on static magnetic characteristic parameters such as initial permeability µi, maximum permeability µm, saturation magnetic induction Bs, remanence Br, coercive Hc and hysteresis losses Pu.
-
Product
Electron Microscope Sample Preparation
-
Excellent sample preparation is the prerequisite for first-class electron microscopy. Be prepared – for great results in EM Sample Preparation! Perfect preparation makes the difference between trying and achieving, between failure and success, between results and excellent results. So be prepared for great results with Leica Microsystems!
-
Product
Economical Load and Force Measurement
ELF
-
Tekscan's ELF force and load measurement system matches the market's need for an inexpensive load and force measurement system with Tekscan's ability to deliver innovative load and force measurement solutions. The system consists of data acquisition hardware, software, and FlexiForce B201 sensors.
