Test Heads
1) interchangeable assembly connecting test signals between DUT and ATE. 2) representation of a human head. 3) provide network test access.
See Also: Heads, Test Probes
-
Product
Digital Test Instrumentation
EDigital-Series™
-
Teradyne’s eDigital IVI driver controls all parallel digital functional test parameters, including per-pin timing, data formats, pattern data, and timing alignment on 64 channels (32 static + 32 dynamic or 32 differential)—each with an 8M pattern depth and results memory.
-
Product
VR/AR/MR Calibration Platform
-
AR, VR and MR device calibration is critical for product performance. Leverage Averna’s standardized alignment platform to efficiently calibrate cameras and Inertial Measurement Unit (IMU) modules with supreme accuracy. Easily customize or upgrade the base platform into the automated quality solution to best fit your manufacturing requirements.
-
Product
PCI Express 3.0 Test Platform with SMBus Support
-
The Summit Z3-16 Test Platform with SMBus Support allows the Summit Z3-16 to act as a host emulator, and provides a general purpose test backplane and interposer for testing Gen3, Gen2 or Gen1 hosts and devices. In addition, it supports the Summit Z3-16 with SMBus Support by providing SMBus tapping connectivity.
-
Product
200 Vdc External Voltage Bias Fixture
16065A
-
Measure a DUT with up to +/-200 V DC bias and also measure axial/radial lead components
-
Product
EMI Test System
TS9975
-
The R&S®TS9975 is the base system for conducted and radiated EMI measurements. Due to its modular design, it covers a wide range of applications and can be very easily adapted to the measurement task at hand. Any configuration is possible – from conducted measurements and the small precompliance system with a compact test cell to the accredited test system for large equipment under test. Combinations of different applications or incremental expansion are easily possible.
-
Product
Imperial Test Executive
ITE
-
The Imperial Test Executive (iTE) is a UI shell that sits on top of National Instruments TestStand. It provides a simple but elegant interface to execute your NI TestStand sequences. The iTE software was designed to allow general operators to execute ATE testing software without requiring any knowledge of NI TestStand. Training an operator to use this system typically takes less then 5-minutes.
-
Product
Functional Test Fixtures
-
Forwessun’s Functional Test Fixtures are tailored to validate the performance of your electronic assemblies, ensuring each product meets critical quality and functional standards. With customisable designs and precision engineering, these fixtures support a range of testing needs—from checking connectivity and function to confirming performance under real-world conditions. Built to handle rigorous demands, Forwessun's solutions are ideal for industries requiring reliable and repeatable results. Whether for high-volume production or specialised testing, our fixtures provide robust, adaptable support to maintain efficiency and accuracy throughout the testing process. We also create, and work with Ingun to create fixtures using the Ingun kit.
-
Product
Square Head Fiber
-
Panasonic Industrial Devices Sales Company of America
Panasonic Square Head Type Fibers are compact and allow for right angle, space-saving installation, with minimum pitch using needle-nose pliers. These Fibers are also lens compatible for longer detection.
-
Product
Component Test Fixture For N1413 With B2980 Series
N1428A
-
The N1428A is designed to operate specifically with the B2985B / 87B electrometer / high resistance meter. It is provided with two component modules, which are used to hold SMD, lead, and various types of devices. Electrical noise effects are reduced by the employment of a shielded case. A built-in interlock circuit enables safe high-voltage measurements. The N1413A high resistance meter fixture adapter is also required to connect the N1428A to the B2985B / 87B.
-
Product
Faraday Chamber for RF w/Exchangeable Cassettes 340x350mm RCV 9025 for 6TL36
AN133
-
The Faraday Chamber is an add-on for the 6TL36 test handler. This kit is installed into the 6TL36 in the same way a normal test fixture would be installed, being the only difference the fact that different products to be tested will, from that moment on, only need an additional exchangeable cassettes to be tested.
-
Product
CDMA2k Analysis Using NI PXI RF Test Instruments
NI-RFmx CDMA2k
-
NI-RFmx CDMA2k is completely interoperable with all NI-RFmx APIs. It provides simple access to the most advanced optimization techniques such as multi-measurement parallelism and multi-DUT measurements. The result is extremely fast and high-quality measurements with minimal software development effort.
-
Product
ESS Performance Test System
-
The Energy Storage System (ESS) Performance Test System is used to evaluate, test, and certify the performance of energy storage systems up to 2MW. The system is a configurable platform with over 200 channels of simultaneously measured AC and DC voltages and currents, environmental temperatures, airflow, and communications. Intuitive software provides real-time monitoring and analysis of power, energy and efficiency to adhere with industry standards. The test system interfaces hardware such as load banks, and controls the ESS to simulate utility applications such as peak shaving and frequency regulation.
-
Product
Kelvin Test Contactor/Probe Head
Gemini
-
At 3.22 mm test height, the Gemini™ Kelvin test contactor is an excellent all-around spring probe with low inductance, high bandwidth, and excellent current-carrying capacity. The device under test (DUT) side tip design accurately maintains its 100 µm spacing for the life of the probe. Customers report typical probe life of 500 k to 800 k package insertions, or over 2M touchdowns at wafer-level test. The offset tip allows manageable board layout with a board-side spacing of 0.4 mm.Gemini Kelvin probes and contactors provide a first-rate solution that effortlessly makes reliable, true Kelvin contact for high-volume final test of both singulated packages and wafer-level devices. Gemini Kelvin is an ideal solution for devices such as power controllers, A-D and D-A converters, power amplifiers and audio and video circuits.
-
Product
OTP-Based Test System
-
Power electronics assemblies often cannot be tested using conventional technology for their electrical performance. Due to the adaptability of the instrumentation, the OTP concept offers an ideal platform even beyond the space requirements of several control cabinets. In order to achieve high test flexibility with different assemblies, the system was equipped with three-phase AC sources and AC loads as well as a precise three-phase power meter. DC sources and loads with different current and voltage ranges cover the test of frequent DUT operating parameters. Time-dependent voltage or current signals can be stimulated by an arbitrary generator with power amplifier. General measurements such as current, voltage, frequency, resistance can be carried out flexibly at various test points using the matrix concept. An oscilloscope with RF multiplexer is available for high-frequency measurements such as residual ripple, switching processes, etc.
-
Product
Test System Optimized for High Throughput, Low Cost of Test for Single Site, Multi-site and Index Parallel Applications
ETS-88RF
-
Targeting the needs of power amplifier (PA) and front-end-module (FEM) semiconductor manufacturers, the ETS-88RF test system is aligned with the test challenges associated with these direct RF radio wave interface components. The precision with which the ETS-88RF can measure high-gain, wideband frequency performance, adjacent channel leakage and power supply efficiency makes this test system the most cost-effective alternative to bench set-ups. Teradyne routinely provides timely updates to a substantial library of RF Standards (such as 802.11xx and 3GPP) targeted for PA and FEM test.
-
Product
Industrial Temperature Head Sensors
-
A selection of Head Mounted Industrial Temperature Sensors for many applications with RTD / PRT varieties, Hygienic and Heavy Duty probes.
-
Product
Attitude Heading Reference System
M&M Modules
-
PNI’s M&M modules will self adapt and learn its system and its environment automatically to provide accurate quaternions, heading, pitch and roll. All while using 100 times less power than traditional AHRS modules.
-
Product
Test Port Cable, 1 Mm
11500K
-
Connect test ports to devices, fixtures, or probe tips with this 20-cm cable featuring a return loss of 16 dB minimum
-
Product
Universal Test System
LEON System
-
A universal ICT, FCT, ISP and Boundary Scan platform.Based on the ABex platform, which directly integrates Konrad analog bus technology and PXI/PXIe in one chassis, the LEON platform can be configured to solve various test challenges. Due to this architecture only one system provides the complete test flow combining ICT, ISP, Boundary Scan and FCT.Various form factors and configurations allow a perfect combination between cost, speed and test coverage. The modular architecture provides the possibility to reconfigure or upgrade the systems based on your test needs.The LEON System software provides a powerful development and test execution environment which directly supports NI TestStand. All systems and components could be integrated into third party software using supplied APIs.
-
Product
Test Contactor/Probe Head
Hydra
-
Engineered for excellence and efficiency, Hydra™ spring probe series offers precision, reliability, and standardized semiconductor test interface.Designed to be best-in-class at a competitive price point, Hydra is optimized to maximize your operational efficiency. Hydra is built to withstand demanding high-volume manufacturing test environments with its robust and durable design.With a common test-height, Hydra offers the ability to mix and match power, RF, and Kelvin probes within the same test socket. In addition, Hydra streamlines inventory management with fewer probe part numbers to manage and shorter lead times.
-
Product
VITA 62, 3U Test Fixture
TF-3U-7B041-1
-
This Power Supply test fixture is being proposed as a tool for checking Injector / Ejector operation, proper alignment of the VITA 62 connector and proper alignment of both keys on a Single slot, 3U, VITA 62/SOSA power supply.
-
Product
chromatic Confocal Sensor Heads
ENDO
-
Sciences et Techniques Industrielles de la Lumière
STIL introduces ENDO series, a new range of chromatic confocal sensor heads with an exceptionally small size.With a mechanical diameter from 4 to 8 millimeters and a straight or radial beam of 90°, ENDO series is ideal for non-contact measurement applications in reduced space environments.
-
Product
Optical Power Meter Heads
-
The 5mm detector area on Keysight's latest optical power heads allows flexible placement of the remote optical power meter, which is then connected to the N7749C. The wide choice of adapters allows input from popular fiber connector types, bare fibers or open beams. The magnetic D-shaped adapters allow rapid removal and replacement without twisting attached fibers.
-
Product
BMS Manufacturing Test System
-
The Battery Management System (BMS) Manufacturing Test System performs functional testing of product during end-of-line manufacturing. The system hardware includes all instrumentation to test a BMS, including multiple cell simulators, a mass interconnect for quick product transition and bed-of-nail fixtures to ensure less down time, higher throughput, and easy maintenance. The system application easily integrates into manufacturing processes, provides a method to test multiple product types, and optimizes tests to ensure only good product is released from manufacturing.
-
Product
Military Communications Test
-
Astronics testers for military radios and wireless communications systems help you keep your most critical communications up and running smoothly. Write test program sets once and deploy them instantaneously everywhere – whether your test set is in the factory, at the depot, or in operation.
-
Product
SoC/Analog Test System
3650-S2
-
The Chroma 3650-S2 is specifically designed for high-throughput and high-parallel testing to provide the most cost-effective solution for fabless, IDM and testing houses.
-
Product
Head Expanders
-
By increasing the mounting area of the shaker, multiple items can be tested at the same time, decreasing total test cycle time. In addition, with Guided Head Expanders, payloads with large foot prints can be safely mounted and tested on the shaker, minimizing the risk of damage to the shaker suspension system. Although many head expanders are resonant below 1000 Hz, average or extremal control allows operation to 2000 Hz.
-
Product
Laser Head Cable, 20 m
10881C
-
Provide reliable power with this five-pin female DIN that connects the laser head to multiple laser boards.
-
Product
Advanced SoC/Analog Test System
3650
-
Chroma 3650 is an SoC tester with high throughput and high parallel test capabilities to provide the most cost-effective solution for fabless, IDM and testing houses.
-
Product
NI Automated Test Software Suite
-
The NI Automated Test Software Suite features all three NI IDEs and NI's most popular application software and add-ons specifically for building your automated test system with confidence. This package offers the power of LabVIEW, LabWindows/CVI, and Measurement Studio combined with the TestStand ready-to-run, test executive and the Switch Executive intelligent switch management application
