Current Sensors
detect AC or DC electrical current.
See Also: Current Probes, SQUID, Voltage Sensors, Rogowski
-
Product
Through Hole type DC Current Sensor／for DC Leakage Current Measurements
DCZCT-20M
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*DC earth fault measurement for solar power system*Least affection from the magnetization of core and temperature fluctuation*DC leakage current measurements*Current measurements for small DC motor*Convenient ＋5V single polarity power supply
-
Product
Monitoring Solar Panel Strings, DC 30A, Φ10mm
CTF-60-10DC
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Compact, Space-saving, Low Cost DC Current Sensors.・Split-core type, easy to apply to existing circuit.・Easy to use by unipolar +5V power supply.・High speed responsibility – less than 10μsec. 0 rated primary current.・Suitable for monitoring solar panel strings.
-
Product
Clamp Meters
-
An electrical testing tool that integrates a basic digital multimeter with a current sensor. Clamps measure current.
-
Product
Clamp Meters
-
Is an electrical test tool that combines a basic digital multimeter with a current sensor. Clamps measure current. Probes measure voltage.
-
Product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-800B Open loop method
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
Product
Through Hole Type AC Current Sensor
CTF-200B
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*For AC current and power measurements.*Suitable for current measurements of main cable.*Measuring range:AC 1A～200A.
-
Product
Surge Tester (Impulse Winding Tester)
SS6815 / SS6815F
-
Surge testers (impulse winding tester) is used for testing and check the insulation grade of turns between turns, insulation grade of layers between layers, insulation grade of windings between turns. It is used widely for transformer, current sensor, voltage sensor, relay, contactor, inductor, motor, generator, valve coil, voice coil, etc.
-
Product
Clamp type AC Current Sensor／for Load Current Measurements(CT Series)
CT-23S
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Ultra compact size*AC 1A～200A*Current measurements of terminal feeder
-
Product
Isolation and Power Solutions
-
Silicon Labs' innovative digital isolation and power product portfolio includes CMOS digital isolators, isolated gate drivers, isolated current sensors, isolated system products and Power over Ethernet (PoE) families. These mixed-signal IC solutions leverage Silicon Labs' superior isolation and high voltage expertise to enhance power system performance, flexibility and reliability while reducing system size and cost. The entire isolation portfolio supports isolation voltages up to 5 kV.
-
Product
Clamp type AC Current Sensor／for Leakage Current Measurements(ZCT Series)
HFCT-34
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
Clamp type AC Current Sensor／for Leakage Current Measurements(ZCT Series)
-
Product
Software-controlled Generator
IPTN16
-
*The module provides output of constant stabilized voltage through 16 independent channels in 2 ranges ± 2 V and ± 10 V with a step of 5 mV, as well as a stabilized current of ± 10 mA with a step of 5 μA.The IPTN16 module is intended for use in information measuring VXI systems and can be used to power resistive temperature sensors or strain gauges with voltage or current with an accurate and stable value.*The IPTN16 module can also be used to simulate voltage or current sensors when checking measuring instruments and channels of measuring systems.
-
Product
SparkFun Current Sensor Breakout
INA169
-
The INA169 is a “high-side current monitor,” which means that you place a resistor (a “shunt resistor”) on the positive power rail and the INA169 measures the voltage drop across that resistor. The INA169 outputs a small current based on the measured voltage drop. If you place a resistor from the output of the INA169 to ground, you can measure the voltage at the output.
-
Product
Clamp type DC Current Sensor／for DC Leakage Current Measurements
DCZCT-18S
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Compact size, General purpose*DC leakage current measurements
-
Product
Clamp type AC Current Sensor／for Leakage Current Measurements(ZCT Series)
ZCT-140S
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Leakage current measurements of feeder*Ultra compact size*AC 1mA～300A
-
Product
Clamp type AC Current Sensor／for Power Monitor
CT-80PB
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*BIG CT WINDOW*AC 1A～500A*Current measurements of main cable
-
Product
High Voltage Ammeter
Ampstik®+
-
Use the Ampstik+ to safely take accurate current measurements when performing high voltage live-line load checks for balancing, switching, or breaking load. This high voltage ammeter measures in every electric utility setting with a linear current sensor to accurately measure .5A to 5000A, while in voltage environments up to 500kV. The opening of the amp sensor is electronically closed, while external currents are electronically rejected. This design enables the user to measure an individual conductor within close proximity to adjacent conductors without interference errors.
-
Product
Clamp type AC Current Sensor／for Load Current Measurements(CT Series)
CT-3000
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Ultra big CT window*AC 1A～3000A*Current measurements of main cable
-
Product
Clamp-On Multimeter Series
-
An electrical test tool that combines a basic digital multimeter with a current sensor. Clamps measure current. Probes measure voltage.
-
Product
Amp, Power Factor & VAR Recorder
Varcorder
-
The Varcorder measures and records Amps and Power Factor. A voltage constant is then applied in software to calculate VARs. The Varcorder uses the same current sensor technology as the original Ampstik. This patented amp sensor does not use magnetic materials and has no moving parts. The opening of the sensor is electronically closed, and external currents are electronically rejected. The accuracy, external current reject, and range of currents measured by the patented amp sensor substantially exceed the performance of the best clamp-on sensors. The true power factor is calculated by measuring the electric field in comparison with the current reported from the amp sensor. The key feature of the unit is the ability to leave it deployed on the line to record readings every 15 minutes for 90+ days. It easily attaches to the line with a standard shotgun style hotstick. Once on the line, it immediately begins to collect and record the current and power factor on the line.
-
Product
Open Loop Current Sensor
C03 30A
-
The C03 offers efficient and precise sensor solutions for direct, alternating and pulsed currents in industrial, commercial and communication systems. It consists of three main components: an accurate, linear Hall sensor with low temperature drift, a flux collector and a transformer. It is characterized by a very low resistance and thus lowers power loss and temperature drift - for optimal performance.
-
Product
DC current Sensors
CTH
-
The CTH sensors convert dc current to an isolated voltage output, the CTHR sensors convert ac current to a dc output signal proportional to the Arms. All popular process control voltage and current loop outputs are available. Through hole or split core options mean that connection is non-intrusive and straightforward. The available input range of the CTH sensors is any value from 5A to 6000Adc.
-
Product
Device Current Waveform Analyzers
-
The dedicated Current Sensors measure from 100 pA level dynamic current up to 10 A with a maximum of 200 MHz bandwidth. The mainframe acquires the signal from the sensors by a maximum of 1 GSa/s sampling speed and 14-bit and 16-bit wide dynamic range. This combination allows you to measure quite wide range of dynamic current, for example, from standby/sleep state to active state, at a single measurement. In addition, the wide bandwidth and the high speed acquisition enable you to measure high speed pulse response even less than 100 ns previously very difficult with existing instruments.
-
Product
±6 kV ANSI/ESDA/JEDEC HBM Test System
HBM-TS10-A
-
High Power Pulse Instruments GmbH
*±6 kV Human-Body-Model (HBM) tester according ANSI/ESDA/JEDEC JS-001 standard with C = 100 pF, R = 1.5 kΩ discharge network*Wafer, package and system level HBM testing*True HBM: the classical discharge network of the HBM-S1-A according the standard ensures compliant waveforms for all load conditions*No trailing pulses*Integrated 10 kΩ charge removal resistor*Integrated DUT HBM current sensor for real time transient current monitoring with 1V/A output sensitivity into 50 Ω digital oscilloscope input*Integrated DUT HBM voltage sensor for real time transient voltage monitoring with 1/200V/V output sensitivity into 50 Ω digital oscilloscope input*Integrated overvoltage protection of the DUT voltage sensor, DUTcurrentsensor and DC test interface for efficient overload protection of the digital oscilloscope and SMU during high voltage HBM testing*Integrated DC test DUT switch with automatic switch control*Integrated 50 Ω precision hardware trigger output for high speed digital oscilloscopes*Fast HBM measurements, typically 0.5s per pulse including one-point DC measurement between pulses*Eficient sofware for system control and waveform data management (fully compatible with TLP measurement data)*The sofware can control automatic probers for fast measurements of complete wafers*Compact size 145 mm x 82.5 mm x 44 mm of the integrated HBM pulse generator probehead*System controller size 483 mm x 487 mm x 133 mm*High performance and high quality components*Optionally available hardware upgrades to all HPPI fully integrated HBM/HMM/TLP/VF-TLP test systems TLP-3010C, 4010C, 8010A, and 8010C
-
Product
Eddy Current Sensor
eddyNCDT 3001
-
The eddyNCDT 3001 is a new, efficient eddy current sensor whose compact dimensions have to date only been reserved for inductive sensors and proximity sensors. The temperature-compensated design provides high stability even in fluctuating ambient temperatures. The eddyNCDT 3001 comes with integrated electronics, offering an outstanding price/performance ratio and easy operation. The eddyNCDT 3001 eddy current sensor is ideally suited to OEM integration and machine building applications. The sensor is factory-calibrated for ferromagnetic and non-ferromagnetic materials, which eliminates the need for field calibration of the sensor. The eddyNCDT 3001 is available with connector or with integrated cable. A robust design combined with the eddy current measuring principle enables measurements in harsh industrial environments (oil, pressure, dirt). In addition, the eddyNCDT 3001 is suitable for offshore/marine applications (salt water).
-
Product
Clamp type AC Current Sensor／for Leakage Current Measurements(ZCT Series)
ZCT-1100
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Leakage current measurements of main cable*Ultra big CT window*AC 1mA～30A : 3080turns*AC 30A～3000A : 2000turns
-
Product
Clamp type AC Current Sensor／for Low Leakage Current Measurements(ZCT Series)
ZCT-110
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Best sensor for low leakage current measurements of less than 1mA.*Suitable for low current measurements of terminal feeder.*High sensitivity and least affection from external magnetic field.
-
Product
PCB IMIC01, 100 mV/g, 2-Pin, Accelerometer, Industrial Vibration Sensor
780985-01
-
The PCB IMIC01 is an industrial Vibration Sensor designed for permanent installations. This sensor helps you acquire sound and movement data with supported PXI Sound and Vibration Modules, C Series Sound and Vibration Input Modules, and USB-based Sound and Vibration Devices. The PCB IMIC01 features a sensitivity range of 100 mV/g and uses the Integrated Electronics Piezo-Electric (IEPE) current excitation. The sensor supports the IMI Industrial Accelerometer Cable as well as the MIL2M-Breakout Cable.
-
Product
PXIe-4464 , 204.8 kS/s, 119 dB, 6 Gains, AC/DC-Coupled, 4-Input PXI Sound and Vibration Module
783087-01
Analog Input Module
204.8 kS/s, 119 dB, 6 Gains, AC/DC-Coupled, 4-Input PXI Sound and Vibration Module—The PXI‑4464 delivers simultaneous sampling on all channels. In addition, the PXI‑4464 includes built-in antialiasing filters that automatically adjust to your sampling rate, six software-selectable input gains ranges, and TEDS smart sensor support for error-free setup. The IEPE excitation circuit can deliver current for high-power sensors and strong data integrity over long sensor cable runs.
-
Product
Current Clamps and Transducers
-
High-accuracy Current Sensors and TransducersHigh-accuracy sensors for AC/DC current measurement and power analysis. From current clamps to high-precision zero flux current transducers and Rogowsky coils.
-
Product
DIGITAL TURNS TESTER AND DIGITAL LCRTZ METER
TURNS-LCRTZ
-
Digital TURNS TESTER with LCR for Counting / Measuring Number of Turns for Toroidal Coils , Current Sensor , Current Transformer , Round Core Coils. Can measure, Turns along with Winding Polarity , DC Resistance , Inductance (L), Capacitance (C), DC Resistance, Rac, Q, D, ESR and Tan.Toroidal Turns Platforms :TTPT100 : 5 T - 1000 T , TTPT1000 : 500T-10000 T The Platform has 2 connections for the coil and 2 for the probe wire. Measurement principle is based on dynamic comparison of the voltage across one turn and the coil. You will be able to get the polarity or winding indication with respect to the one turn reference.Accuracy : + 0.2% + 0.5T for high and medium permeability cores at suitable test frequency. Internal Diameter must be able to pass a wire as thin as 0.2 mm. External Diameter as high as 200 mm.Test Frequency Selectable in Step : 50 Hz, 100 Hz , 500 Hz, 1 KHz, 5 KHz, 10 KHz. Test Voltage adjustable : 100mV to 1V in steps of 50mV.
