Polarity
See Also: Polarity Testers
-
product
Avionics Data Bus Tester
Distributed CORVUS
Distributed CORVUS works in conjunction with CORVUS-300 to isolate bus anomalies and fault resolution. The Transmit unit, C-9235-TX, sends 1553 like data pattern through a bus stub and coupler to the Receive unit, C-9235-RX, on another stub. This will measure insertion loss, possible bit errors and correct polarity. The Receive unit can also be used to give a digital scope representation of the active data bus showing signal quality and peak to peak amplitude.
-
product
E-Z Check® Plus GFCI Circuit Tester
61-051
*Tests for correct wiring, open ground, reverse polarity, open hot, open neutral, hot on neutral, hot and ground reversed with open hot in 3 wire, 120 VAC circuits*Simulates ground fault for testing GFCI*No-slip ergonomic design maximizes comfort*Premium neon lamps prevent false readings*Tough, impact-resistant case*2-year warranty
-
product
Polarization Controller and Scrambler - PXIe
Pol 1000 Series
The Pol 1000 Series PXIe module enables high-speed automated polarization control for polarization dependent testing procedures.Rotate or scramble the polarization of your signal with no need for manual adjustment of paddles or tension screws using intuitive software, LabVIEW or comprehensive SCPI commands. Pol 1000 Series can be used with our wide range of optical and electrical PXIe test modules, and can be used to build complete mixed-signal test platforms.
-
product
Polarimeters
GAOTek’s polarimeters measure the rotation of polarized light as it goes through an optically active solvent by using the polarimetric technique. To calculate the value of the solution concentrations, it must determine the measured rotation. Our instruments are also ideal for various applications such as chemical, food, beverage, and medical fields. GAOTek’s high-performance polarimeters are reliable and inexpensive equipment that provide an accurate measurement for easier inspection or testing. They are compact, easy to carry and portable to allow the user to work in complex conditions and on-site.
-
product
6 Channel 6 kV/20 µA VME HV Power Supply
V6521H
The V6521H is a 1-unit wide VME 6U module housing 6 High Voltage Power Supply Channels 6KV, 20µA. The board is available with either positive or negative output polarity; mixed version with 3 positive and 3 negative channels is also available.
-
product
Analogue+Digital Multimeter
ST-3502
Standard Electric Works Co., Ltd
● 3½ digit, high contrast LCD, with a maximum display of 1999● Automatic polarity indication, zero adjustment● Low battery (BAT) indication● Over range indication: highest digit of (1) or (-1)● EN 61010-1 CAT III 600V, EN 61326-1
-
product
Cylindrical Photoelectric Sensor
CY-100 SERIES
Panasonic Industrial Devices Sales Company of America
CY-100 Series Sensors are available as Thru-Beam, Retroreflective (with and without polarization filters) and Diffuse Reflective Types. Standard (Axial) and Side-View (Radial) Types are available, providing flexibility when mounting the Sensors. Moreover, all Sensors can be ordered as a cable type or with an M12 plug-in Connector.
-
product
Receptacle Tester
RT500
Designed to detect the most common wiring problems in standard 120V receptacles.Test for correct wiring, open ground, reverse polarity, open hot, open neutral, hot and ground reversed.Conditions NOT indicated: Quality of ground, multiple hot wires, combinations of defects, reversal of grounded and grounding conductors.Large light indicators for greater visibility.Reinforced prongs for increased durability.Push-pull design with slip-resistance ribbing.Made in USA of U.S. and imported parts.
-
product
Spot-Focusing Lens Antennas
The antenna employs a low loss lens to offer excellent aperture efficiency at 105.96 GHz. The lens antenna is equipped with a standard WR-10 waveguide and UG-387/U-M flange as its input port. It supports linear polarized waveforms.
-
product
Current Transformer Tester
CTT
The CTT is designed to test the current transformer ratio, Phase shift, Polarity, Excitation, Saturation, Winding resistance and Insulation resistance using the voltage method in compliance with ANSI/IEEE C57.13.1 and IEC 60044-1 standards, where voltage is applied to the secondary X terminals of the current transformer.
-
product
High-Voltage Test Device
PGK 150 HB
BAUR Prüf- und Messtechnik GmbH
Cable testing and diagnostics with the BAUR PGK HB. There are hardly any other longer-lasting, more robust and cost-effective testing devices than the two-piece high-voltage test devices from the PGK HB series. They generate continuous adjustable test voltages with mains frequency or optionally DC with positive or negative polarity. The display instruments for current and voltage, the safety control unit and the regulating transformer for the voltage are integrated in the operating unit.* Operation as DC or AC testing device* Polarity of the DC voltage can easily be reversed* Robust and durable
-
product
Chromatography System
ACQUITY UPC2
With the ACQUITY UPC2 System, the orthogonal capability of normal-phase LC has been elevated to a mainstream technique: *Convergence Chromatography. The chromatographic principles and selectivity of normal-phase LC *The ease-of-use and method development simplicity of reversed-phase LC *The use of gradients across the widest polarity range *Chiral and achiral separations in one system, with unequaled speed and confidence
-
product
Dual Polarized Broadband Horn Antennas
Linear polarized dual double ridged broadband antenna for receive and transmit applications made of aluminium.
-
product
Polarization Maintaining Band Pass Filter
Zhongke Rayzer Optical Technology Co.,Ltd
Selects the thin film filter withgood performance to ensure the high quality opticalperformance, stability and reliability. It is uses to shieldnoise signal in EDFA and fiber laser system. It has thecharacteristics of high isolation, low insertion loss, highreturn loss and high power.
-
product
PXI Solid State Multiplexer Module, Dual 3-Channel, 30 A
40-667C-011
The 40-667C-011 is a dual 3-channel 30A MUX and is part of our range of high current multiplexers occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
product
Digital ELCB (RCD) Tester
2712 EL
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● 2 Lines × 16 characters LCD.● Very low consumption.● 50Hz and 60Hz operation.● Menu-driven.● Accurate digital readout of disconnection time.● Automatic data hold function.● Over temperature protection.● Over voltage protection.● Fuse protection.● Zero crossing circuitry permit testing at 0° or 180°.● Disconnection phase polarity shown on LCD display.● Auto off and off override.● Polarity trip indicator (positive or negative phase)● Wiring polarity indicator.● Measure voltage between Line and Earth before testing.● Frequency measurement indication.
-
product
Voltage/Continuity Testers
VOT-53
Standard Electric Works Co., Ltd
● 2000-count digital display (LCD type). ● Test leads positioned at 19mm apart.● Interchangeable probe tip for 2mm and 4mm.● Polarity test ● Audible continuity test.● Auto sensing function for: voltage (AC/DC), Ω, diode.● Measurement function: ACV/DCV: 1000V Resistance: 2000Ω Frequency: 30Hz~1kHz ● Phase rotation test : ● Waterproof design, protection class: IP65.● Phase / Neutral identification.● Rubberized double-molded housing.● Flashlight function.● Safety standard : EN 61010-1 CAT III 1000V EN 61010-1 CAT IV 600V EN 61243-3 EN 61326-1
-
product
Surge / DC Hi-Pot Consoles
HC Model
(Surge / Hi-Pot Consoles) - Now available in High Voltage models - 35,40 & 50KV. The HC Model offers Surge / DC Hi-Pot testing capabilities! The "HC" Model has all of the features of our "C" Model plus a DC Hi-Pot Tester. DC Hi-Pot includes dual LED panel meters that display direct read out of current and voltage, with overcurrent safety trip and the capability of ascertaining Polarization Index (PI) Test results.
-
product
Polarization Instrumentation
This page features the optics and instrumentation necessary to control and measure the polarization of light. Our free-space and fiber-coupled polarimeters can measure any state of polarization (SOP) on the Poincaré sphere.
-
product
Multi Operational Surge Tester (MOST) Consoles
MC Model
Digital Surge, DC Hi-Pot & Built-In 3 Phase Test Selector Switch all-in-one versatile Tester. The DC Hi-Pot tester has separate panel meters for direct readout (voltage and current) so that no interpretation on the scope's display is ever needed and enables one to ascertain Polarization Index (PI) Test results.
-
product
Transformer Polarity Tester
PMT20030
Power Measurement Technologies Inc.
A hand held instrument for polarity identification of current, voltage and power transformers with an operable ratio range from 1:1 to greater than 5000:1.
-
product
4-Band SAT-IF Overlay Direct Modulated Optical Transmitter
HDS-55S ( 950~5500MHz )
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HDS-55S series 1550nm wide band micro-wave internal modulation optical transmitter, RF working 950~5450MHz.It cam It can transmit multi( stacker) 4 way SAT-IF signal in one fiber to realize two polarized 4 way SAT-IF signal in one satellite。or 4 way SAT-IF signal in different satellites to convert all of them into one fiber.。Through FTTH,users use ordinary satellite receiver and STB to receive satellite video carrier the integrate TV programs. It can supply high quality of satellite TV service up to 3000 SDTV or 600 HDTV channel.
-
product
S2 Ultra High Sensitivity Sensors
ULP-S2 UHS
Universal LightProbe S2 Ultra-High Sensitivity Sensors are designed for the test of very dim LEDs, as low as 0.01 mcd minimum, and including very low light-level LED-illuminated action-indicator switches, controls and status indicators for night/dark viewing in automobile interiors. Recommend the use of wide-aperture stainless- steel encased Fiber- optic Probes with contacting tips.Operating temperature range: 0oC to 70oCPower consumption: Operates between +5 and 28 volts D.C., at 6mA max. Less than 4.75 volts is not recommendedVoltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsSignal Output Loads: 20 mA max. Non-inductive.Output Pins: 3 gold-plated standard wire-wrap pins (0.025 in. sq.)Sensor Size: 0.560 in. dia x 1.38 in. long.Typical response times: <190mSFiber-Optic Probes: Wide-Aperture Fiber-Optic Probe recommendedDesigned for the test of very dim LEDs, as low as 0.01 mcd minimum
-
product
X-Ray Inspection
X-ray inspection systems are used wherever defects need to be detected by non-destructive means. The spectrum of use is broad and ranges from quality controls for complex assemblies, to the testing of materials for cracks and air inclusions, to foreign matter inclusions and shape deviations. The trend toward miniaturization, higher packing densities, and the relocation of components to the interior of the assembly require precise X-ray inspections that detect hidden defects quickly and reliably. X-ray systems from Viscom are used for the inspection of series assemblies as well as sampling and prototype controls. They take care of typical inspection tasks in concealed areas such as void controls, THT filling level measurements, and HIP inspections. At the same time, the systems reliably determine defect features such as coplanarity and polarity – at high inspection speeds and in a cost-effective way.
-
product
Horn Antenna
ZLB7-SJ12-40G-1015
Dual Polarized Horn Antenna, Frequency 12~40GHz, Gain 12dBi,Iso 25dB Typ., 2.92mm Female connectors, Small Size 55*55*82mm, 5G Mesurement.
-
product
PXI Solid State Multiplexer, 30 Amp, Dual 3-Channel
40-667A-011
The 40-667A-011 is a dual 3-channel 30A MUX and is part of our range of high current multiplexers occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
product
High Voltage Probe
HVP-40M
*DC 40KV CAT II Pollution 2*600MΩ Impedance*25KV ± 2%, 40KV ± 3%*T.C. 200 ppm/oC*Positive Polarity only.*Resolution 1KV*Need not power.*CE, TUV GS, UL, CUL, IEC1010
-
product
Test Probes
Our innovative Test Probes are the upgrade version of Auto Multi Meter. It can perform multiple circuit system test such as power supply feed, voltage and resistance measurement, continuity test, ground test, polarity check and components activation.
-
product
12-440V AC Multi-Function Tester
1965
Peaceful Thriving Enterprise Co Ltd
*Pocket clip.*Bright LED indication.*No test leads required.*Screwdriver voltage probe.*Check voltage on 12-440V AC.*With UL and RoHS Approval.*Two LR44, 1.5V batteries included.*Tests for voltage, continuity and polarity.
-
product
Antenna, Tactical, Log Periodic
EM-6942 | 400 MHz – 4 GHz
The EM-6942 is designed for harsh environmental conditions and its folding elements and 2-section design simplifies transport and storage. The antenna can be mounted on a tripod or any ¼-20 mount and be positioned for horizontal or vertical polarization.





























