Backplanes
An interconnection structure allowing multiple printed circuit boards to coexist using a single bus.
-
Product
JadeFX Kintex UltraScale Processor and FMC Carrier - 3U VPX
Model 5983
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family BrochureVITA-57.4 HSFC FMC+ site offers access to a wide range of possible I/O- Supports Xilinx Kintex UltraScale FPGAs- 9 GB of DDR4 SDRAM- On-board GPS receiver- PCI Express (Gen. 1, 2 and 3) interface up to x8- User-configurable gigabit serial interface- LVDS connections to the Kintex UltraScale FPGA for custom I/O- Optional optical interface for backplane gigabit serial interboard communication- Compatible with several VITA standards including: VITA-46, VITA-48 AND VITA-66.4 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available
-
Product
PCI Express 4.0 Test Platform
Test Platform
The PCI Express 4.0 Test Platform provides a convenient means for testing PCIe 4.0 add-in cards with an internal interposer and power supplies. The Summit Z416 Test Platform provides the platform for the Summit Z416 to act as a host emulator, and provides a general purpose test backplane and interposer for testing Gen4, Gen3, Gen2 or Gen1 hosts and devices. It supports SMBus and other sideband signals.
-
Product
6U, CompactPCI/PXI module
CP213
-
The CP213 is a single-width, 6U, CompactPCI/PXI module with either 32 or 64 differential analog input channels that can alternately be configured under software control as 64 or 128 single-ended analog input channels. A 16-bit ADC scans each channel at a scan rate chosen by the user. The number of channels scanned and scan rate are software selectable. Scans may be triggered from either the internal clock, one of eight PXI backplane triggers, the PXI star trigger bus or an external SMB connector on the module front panel. Single and continuous scan operations are supported. If single scan operation is chosen, an interrupt may be generated at the end of the scan.
-
Product
15-Slot 32-Bit 3U I/O with 6U System CompactPCI Backplane
cBP-6515R
Backplane
- PICMG:2.0 R3.0, 2.1 R2.0, 2.7 R1.0- Dimension:202.5 x 262.05 (mm, WxH, vertical insertion view)- Segment:One- cPCI Bus:32-bit/33MHz- System Slot:Right-hand side- System Slot Rear I/O:P3, P4 and P5 rear I/O with AB-type shroud- Peripheral Slot:14 (Bus A: 7 slots, Bus B: 7 *slots)Note- Peripheral Slot Rear I/O:P2 rear I/O with AB-type shroud
-
Product
Digital Processor
DP7000
-
The DP 7000 Digital Processor with 40/100G Ethernet or 169G Interlaken protocol compatible MPO/MTP® Optics, designed for evolving markets such as Real-Time Stream Processing for High-speed Data-acquisition (DAQ), High Performance Computing (HPC), Machine Learning, Data Center Infrastructure, AI Processing and Network applications. The board is 8U form factor, 322.25 mm x 280 mm x 6 HP (L x W x H), single slot AXIe or AdvancedTCA® blade, ideal for multi-slot 19″ rack mount system integration. In AXIe form factor it provides up-to Gen3 PCIe® backplane connectivity.
-
Product
Power Interface Board 3 HE, 2PSU-Steckverbinder
106PIBM302-0000R
-
The PIB 3U 2 slot has two power connector P47 and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
-
Product
PXI 8 Slot 3U
-
Comtel PXI Backplanes 8 Slot 3U. A number of versions are available that cover a wide range of needs. If you have a requirement for PXI Backplanes and/or Systems, please contact Comtel for further information.
-
Product
3U CompactPCI® Subsystem with 13-slot Backplane, 2 + 1 CompactPCI® Redundant Power Modules
cPCIS-2633 Series
Backplane
- 3U CompactPCI® backplane with 12 peripheral cand slots and one system slot- 2 + 1 hot swappable 500 W + 250 W CompactPCI® Power supply (supports three 250 W PSUs)- Temperature, voltage, and fan monitoring LEDs- Supports current sharing on +5V, +3.3V, and +12V- PICMG® 2.11 47-pin power interface- Hot-swappable cooling fans & filter
-
Product
96 Channel I/O and 64 Channel I/P VME Module
DP-VME-3132
-
The DP-VME-3132 provides 96 channel RS422 differential digital I/Os and 64 channel RS422 differential isolated inputs on the front end and rear side. On the rear side, it is interfaced with the VME 64x backplane.
-
Product
Power Interface Board 3 HE, 1PSU-Steckverbinder mit AC-Pins
106PIBM301-9001R
-
The PIB 3U 1 slot has one power connector P47 with AC pins and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
-
Product
DG I/O Backplane Extender Board
9286-1015
-
15" x 15" Backplane Adapter. Not to be used in production environment. Used with any I/O bus adapter during installation of Hawk system. Presents Nova/Eclipse bus signals on dual 50-pin connectors. Two 10 ft. (3 m) ribbon cables included.
-
Product
4U Rackmount Chassis
Chassis
4U rackmount chassis is a cost-effective computer chassis featuring a complete line of backplanes, power and storage device options. The 4U computer chassis provide the best support for various wallmount and rackmount system.
-
Product
19" Rackmount
-
Packaging solutions engineered using modular design methodology providing countless combinations of card slot count, backplane architecture, power, cooling, height and depth leading to reduced cost, lead-time and program risk. Standard options from 1U through 14U to house: VME, VME64x, OpenVPX, CompactPCI/CompactPCI-Serial and AdvancedTCA architectures. From commercial grade to MIL-STD applications, Elma’s packaging solutions provide your systems the protection you need.
-
Product
Power Interface Board 3U, 2PSU connectors with AC pins
106PIBM302-9001R
-
The PIB 3U 2 slot has two power connector P47 with AC pins and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
-
Product
Tx/Rx SignalBlade
-
This ATCA compatible test card offers the flexibility to verify the performance of Advanced TCA fabric and base channels. The set of four Transmit pairs and four Receive pairs allows access to a full channel's eight pairs for backplane path characterization. The card includes a HM-ZD connector segment for access to the backplane and edge-launch SMA connectors for ease of test cable attachment. DC blocking capacitors are included on the receive pairs as required by Advanced TCA.
-
Product
13-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB112
-
*Designed for PICMG 1.3 SBC*Compatible with the AX61400, AX6145, and AX6156LE chassis*Supports one PICMG 1.3 CPU card slot, one PCIe x4 slot, one PCIe x16 slot, and ten 32bit/33MHz PCI slots
-
Product
3U CompactPCI Serial 2-slot SSR w/ RTM w/ Ethernet
1CPCIS-302-R210
-
3U CompactPCI Serial Backplane with 2 CompactPCI S.0 slots, system slot right, with rear IO : 1x CompactPCI S.0 CPU slot, 1x CompactPCI S.0 peripheral slots, with connectors for RTMs in slot 1, full-mesh Ethernet routing.
-
Product
VME J1 5 Slot with ADC Connectors
101VMEJ105-0590R
-
VME J1 backplane 5 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
Product
6U CompactPCI Rear Transition Module With AMD MXM Graphics Module, CPCI-R6500 Series
20040266
-
The cPCI-R6500 Series is 6U CompactPCI rear transition module (RTM) designed for use with ADLINK 6U CompactPCI CPU blades. The cPCI-R6500 is an RTM equipped with an ATI graphics module to provide additional graphics performance for embedded applications and supports comprehensive rear I/O functionality. Dual independent display output is via two DVI ports and an onboard Realtek ALC262 High Definition Audio Codec provides analog audio output from the audio controller on the CPU blade. The cPCI-R6500 requires a compatible 6U CompactPCI backplane with rear I/O support and correctly configured CPU blade.
-
Product
PCIe X8 And X1 Bridge Card
-
The Guzik PCI Express Host Interface Bridge Card was designed to expand the x8 PCI Express Gen 2 (PCIe) slot in a host PC to an AXIe or a Guzik GSA 6000 chassis via a x8 PCI Express Gen 2 and a x1 PCI Express Gen 1 high speed PCI-SIG specified data cables. This allows the end node to connect to the host bus at speeds up to 3.2GByte/sec user data rate. The Bridge Card installs in a x8 or x16 slot of a PCIe backplane or a PCIe motherboard, provides additional board-based retention and reinforced front panel.
-
Product
VME & CPCI Systems
-
Verotec has a selection of configured systems plus individual elements such as backplanes, power supplies and cooling products, compliant with the PICMG / VITA specifications, and supported by a range of accessories. We offer these in standard VME and CompactPCI platforms across various mechanical form factors with customising options to suit specific applications.
-
Product
Signal Integrity Evaluation up to 26.5 GHz
N5222BT
Network Analyzer
The N5222BT provides the N5222B 26.5 GHz PNA, application software including PLTS and enhanced TDR, and accessories for signal integrity evaluation of cables, backplanes and BGA packages.
-
Product
VME64X 6U 10 Slot with P0
101V64XC10-0621
-
6U VME64x Backplane 10-slot with P0, compliant with ANSI/VITA 1.1-1997, VME extension standard. Includes termination passive inboard, daisy chain automatic active, and power bugs on top and bottom of slots.
-
Product
Analog Backplane Interface Board
MSXB 029
-
The Microstar Laboratories Analog Backplane Interface Board, part number MSXB 029, interfaces the Analog Backplane with a Data Acquisition Processor. The Analog Backplane Interface Board must be installed in the Analog Backplane to connect the backplane to a Data Acquisition Processor.
-
Product
VME64X 7U 3 slot no P0
101V64XM03-0620R
-
7U VME64x Backplane 3-slot w/o P0, compliant with ANSI/VITA 1.1-1997, VME extension, and VITA 1.7 Increased Current. The extra 1U provides room for extra power bugs or busbars. Includes termination passive inboard and daisy chain automatic active.
-
Product
ATCA 5U 7 Slot replicated Mesh - dual shelf managers
109ATCA507-3000R
-
The 5U 7-slot ATCA backplane is a Replicated Mesh, compliant to the PICMG 3.0 Rev 3.0 specification. Elma Bustronic’s ATCA backplanes have been simulated and characterized by our signal integrity lab to optimize performance.
-
Product
VPX Development Systems
-
development system with Backplane Profile BKP6-CEN06-11.2.5-n. Specifically supports OpenVPX and VPX REDI 6U convection or conduction cooled boards and modules.
-
Product
Programmable Multifrequency Clock Synthesizer - 6U VPX
Model 5891
-
- Simultaneous synthesis of up to 10 different clocks- 16 SMC clock outputs- Typical phase noise: -105 dBc/Hz @ 1 kHz offset- All clocks are phase-locked to input reference signal- Input reference frequency of 5 to 100 MHz- Eight programmable VCXOs with 32-bit tuning resolution- Output clocks of 1, 2, 4, 8, or 16 submultiples of VCXO base frequencies- Output clock frequencies between 50 and 700 MHz- Control and status over the VPX backplane
-
Product
PCIe 5.0 Test Platform
PXP-500A
Test Platform
The Teledyne LeCroy PXP-500A Test Platform provides a convenient means for testing PCIe 5.0 cards with a self-contained portable and powered passive backplane. The PXP-500A provides power required for both cards under test.
-
Product
VME64x VITA 1.7 Backplanes
-
Atrenne VME64x VITA 1.7 backplanes comply with ANSI/VITA 5.1, include a 12-layer low noise striplinedesign with outside layers, which incorporates a chassis ground EMI shield and are available in customer configurations.
