VME Carriers
-
product
Compact PCI Express (3U) Generic Carrier Card
ACCx-1
To complement the wide range of interface modules for dedicated Avionics Databuses and Networks, AIM offers a range of Carrier modules for the use of AIM or any 3rd Party PMC and XMC module on various backplanes.
-
product
PCI-Express Generic Carrier Card
ACPe-1
PCI-Express generic carrier card for PMC (PCIbus mezzanine card) modules with 1 PMC slot. Modular solution combines any AIM PMC module for AFDX®/ARINC664P7, ARINC429, MIL-STD-1553 or any standard 3rd party PMC module.
-
product
VME J1 7 Slot with ADC Connectors
101VMEJ107-0590
VME J1 backplane 7 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
product
6U VPX & VME Systems
Curtiss-Wright Defense Solutions
Our 6U VPX and VME rugged mission computer systems are pre-integrated and pre-validated to reduce your cost, risk, and time to market. These systems are based on open standards to meet Modular Open Systems Approach (MOSA) requirements and qualified for temperature extremes, high altitudes, voltage spikes, shock, vibration, and more.
-
product
6U VME Monolithic Classic 5-slot With 70A Power Bolts
30510-205-0000
6U VMEbus monolithic backplane 5-slot, VITA, termination passive inboard, daisy chain automatic active, power connection 70A power bolts, I/O pins 13mm gold-plated, shroud (1P1, nJ2) without latches
-
product
Carrier with System Management
EnsembleSeries™ CCM3011
*OpenVPX carrier module designed to use the Data Plane*PCI/PCI-X interface at up tof 133 MHz on each site*x8, x4 and x1 PCIe interfaces*Advanced OpenVPX system management functionality enables remote monitoring, alarm management, and hardware revision and health management*Conduction-cooled and air-cooled variants available
-
product
PCIe FPGA Carrier For FMC+, VU13P UltraScale+TM
PCI596
The PCI596 is based on the Xilinx VU13P UltraScale+TM FPGA, which provides over 12,000 DSP slices, 360 Mb of UltraRAM and 3,780K logic cells. The FPGA interfaces directly to the FMC+ DP 0-31 and all FMC+ LA/HA/HB pairs, making it compatible with a wide range of industry standard VITA 57 and VITA 57.4 modules. It also has interface to DDR4 memory channels (1x 64-bit wide, 8 GB). This allows for large buffer sizes to be stored during processing as well as for queuing the data to the host. PCI596 has x16 PCIe edge connector routed to the FPGA PCIe Gen4 hard IP block. In addition, 16 uncommitted connection pairs are routed to a dual x8 expansion connector, providing direct connectivity to a neighbouring FPGA (e.g. via Aurora, 10/40GbE, SRIO, PCIe) without the need to go through the host.
-
product
Module for VME & VXI Systems
EXC-4000VME/xx / EXC-4000VXI/xx
The EXC-4000VME/xx and EXC-4000VXI/xx cards for VME & VXI systems supports up to eight dual redundant MIL-STD-1760 channels using the M4K1553Px(S)-1760 module and is compatible with all common variations of MIL-STD-1760 (A, B). Each channel can operate simultaneously as a Bus Controller and up to 32 Remote Terminals and as a Triggerable Monitor. In addition, Checksum, SRQ bit and Header Words are supported on each channel.
-
product
Quad M Module Carrier
DP-cPCI-5112
DP-cPCI-5112 provides a compact high performance cPCI bus gateway to four ANSI approved M-Module Interfaces. This is a non-intelligent 6U form factor M-Module Carrier board. The DP-cPCI-5112 allows a flexible I/O solutions to be implemented in the carrier board. The M-Module carrier board occupies single slot in a CompactPCI system. Different mix and match of various I/O solutions will simplify the job for system integrators.
-
product
VME J1 8 Slot with ADC Connectors
101VMEJ108-0590
VME J1 backplane 8 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
product
ARINC825 (CAN Bus) Test & Simulation Module for VME With 4, 6 Or 8 CAN Bus Nodes
AVC825-x
ARINC825 (CAN bus) Test & Simulation Module for VME with 4, 6 or 8 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The AVC825-x VME card can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
product
3rd Gen MicroTCA Carrier Hub (MCH), Double Module, 40/10GbE/PCIe/FPGA/SRIO
UTC006
The VadaTech UTC006 is a double module, MTCA.4 format, MCH with front-panel fabric expansion and RTM support (PCIe optiononly). Fabric options include PCIe Gen3, 10/40GbE, Xilinx Virtex-7 FPGA, Cross Bar Switch (CBS), and SRIO.
-
product
Hardware Modules for PXI, PCI, PCI Express, USB, Ethernet, VME, and VXI
MIL-STD-1553
Avionics Interface Technologies
MIL-STD-1553 hardware modules for PXI, PCI, PCI Express, USB, Ethernet, VME, and VXI provide advanced features and functionality to support even the most demanding test and simulation applications.
-
product
VME Test Extender 6U/220mm 64X with P0
116EXT6122-0125R
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
product
6U Single VME Slot Intelligent Interface Card
IIB-3910-VME-2C
The IIB-3910-VME-2C is a 6U single VME slot intelligent interface card providing complete STANAG 3838 andSTANAG 3910 test, simulation and bus analysis capability, for two 3838 dual redundant and two 3910 buses, which support optical dual redundant and electrical single redundant 3910 protocols.
-
product
COM Express® Type 6 R3.1 Reference Carrier Board In ATX Form Factor
Express-BASE6 R3.1
Express-BASE6 R3.1 is an ATX COM-Express Type 6 Basic / Compact size module reference carrier board based on PICMG COM-Express Revision 3.1. Together with the COM-Express Type 6 module of your choice and off the shelf add-on cards, you can quickly emulate the functionality of your desired end product for software development and hardware verification.
-
product
Dual Industry Pack Carrier Module
CPCI-SIP-rp
The CPCI-SIP module provides a 3U high performance flexible I/O scheme that supports industry standard Industry PacksÔ. For application requiring low cost, high density I/O or unique combinations, the CPCI-SIP is the perfect solution.The CPCI-SIP is also available with the Industry Pack lines routed to the CompactPCI P2 connector for application that require rear panel I/O.
-
product
Interface for the Multimode, multiprotocol Excalibur 8000 Family of Carrier Boards, Providing a Complete Solution for Developing & Testing MIL-STD-1760 Interfaces
M8K1760Px(S)
The M8K1760Px(S) interface module for the multimode, multiprotocol, Excalibur 8000 family of carrier boards provide a complete solution for developing and testing MIL-STD-1760 interfaces and performing system simulation of the MIL-STD-1760 bus. The module handles all standard variations of the MIL-STD-1760 protocol.Each M8K1553Px-1760 multi function module contains 64K bytes of dual-port RAM for Data blocks, Control registers, and Look-up Tables. All Data blocks and Control registers are memory mapped, and may be accessed in real time. Each of the independent dual redundant M8K1760Px modules may be programmed to operate in one of three modes of operation: Remote Terminal, Bus Controller/Concurrent-RT, and Bus Monitor. In addition, modules 1 and 3 can be programmed to operate as Concurrent monitors, to modules 0 and 2 respectively.In addition, Checksum, SRQ bit and Header Words are supported on each channel, as well as, error injection (BC and RT modes) and error detection (all modes).Each M8K1760PxS single function module operates either as a Bus Controller, Remote Terminal, or Bus Monitor.The M8K1760Px(S) comes complete with Windows software, a C-driver software library including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application
-
product
6 Channel 6 kV/1 mA VME HV Power Supply
V6534
The V6534 is a 1-unit wide VME 6U module housing 6 High Voltage Power Supply Channels 6kV, 1mA. The board is available with either positive or negative output polarity; mixed version with 3 positive and 3 negative channels is also available.
-
product
1, 2, 4 Or 8 Stream MIL-STD-1553Test And Simulation Module For VME (6U)
AVC1553-x
MIL-STD-1553 Test and Simulation module for VME (6U) with 1, 2, 4 or 8 dual redundant channels.Integrated modular solution by using the AMCX1553-x PMC cards installed on AIM’s AVC-2 Generic VME64x (6U) Carrier card.
-
product
VME Extender
VMEE-M
VECTOR Electronics and Technology, Inc.
VMEEJ1 Extender on top and VMEEJ2 Extender on Bottom
-
product
PCI to PMC Adapter / Carrier
PCIBPMCx2
Embedded applications frequently require real time processing coupled with special purpose IO. With the PCIBPMCx2´s two slots; a PrPMC can be matched with another PMC to make a high bandwidth processing node. The PrPMC can communicate with the host for set-up, and then use the local bus to control and transfer data with the special purpose IO card.
-
product
VME J1 12 Slot with ADC Connectors
101VMEJ112-0590
VME J1 backplane 12 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
product
Squid Carrier Board™ Family PCI Express Gen 3 Carrier Board for 4 M.2 PCIe SSD Modules
SKU-086-B4
B-series PCI Express Gen3 Carrier board was designed as a cost-effective storage solution for the systems that are using a motherboard with PCI Express bifurcation support. Such motherboards can be configured in the BIOS to split x16 PCI interface to four PCI Express interfaces by utilizing the following PCIe lanes:- x4 PCI Express interface 1: lanes 0,1,2,3 from x16 PCIe interface;- x4 PCI Express interface 2: lanes 4,5,6,7 from x16 PCIe interface;- x4 PCI Express interface 3: lanes 8,9,10,11 from x16 PCIe interface;- x4 PCI Express interface 4: lanes 12,13, 14, 15, from x16 PCIe interface;
-
product
Squid Carrier Board™ Family PCI Express Gen 3 Carrier Board for 6 MiniPCI Express Modules
SKU-085-31
PCI Express Carrier board for 6 MiniPCI Express modules was designed to expand modern motherboards with PCI Express interface. It is the first carrier board in the Squid family with MiniPCI Express 2.1 and PCI Express Gen 3 Specifications support.
-
product
PCIe FPGA Carrier For FMC, Virtex UltraScale™
PCI595
The PCI595 is based on the Xilinx XCVU440 Virtex UltraScale FPGA, which provides 2,880 DSP slices, 88.6 Mb RAM and 5,541,000 logic cells. The FPGA interfaces directly to the FMC DP 0-9 and all FMC LA/HA/HB pairs, making it compatible with a wide range of industry standard VITA 57 modules. It also has interface to one DDR4, 64-bit wide, with 8 GB total memory. This allows for large buffer sizes to be stored during processing as well as for queuing the data to the host.
-
product
3U CompactPCI® Quad Mini PCIe & M.2 Carrier Board
MIC-3954 D&E
The MIC-3954 series is a carrier board compliant CPCI-S.0 standard to support two kinds of functions by BOM option. It is routed by PCIe and USB2.0/3.0 interface to mini PCIe or M.2 connectors. It allows users to use different types of Mini PCIe or M.2 form factor modules for wireless connection.
-
product
VME J2 20 slot
101VMEJ220-0900
VME J2 backplane 20 slot, compliant with ANSI/VITA 1-1994. The A+C rows are bussed in all slots. Also, row B has onboard, inboard termination.
-
product
PCIe FPGA Carrier For FMC+, Altera Arria-10 GX1150
PCI536
The PCI536 is based on the Altera Arria-10™ GX1150 FPGA in F1517 package. The FPGA interfaces directly to the FMC+ DP 0-23 (single connector) and all FMC+ LA/HA/HB pairs, making it compatible with a wide range of industry standard VITA 57 modules. The PCI536 has x8 PCIe edge connector routed to the FPGA PCIe Gen3 hard IP block. It also has interface to two DDR4, 64-bit wide, with 16 GB total memory. This allows for large buffer sizes to be stored during processing as well as for queuing the data to the host.
-
product
VME & CPC Systems
Verotec has a selection of configured systems plus individual elements such as backplanes, power supplies and cooling products, compliant with the PICMG / VITA specifications, and supported by a range of accessories. We offer these in standard VME and CompactPCI platforms across various mechanical form factors with customising options to suit specific applications.
