VME Carriers
-
Product
VME64x IP Carrier Module
DP-VME-5121
-
Data Patterns DP-VME-5121 VME IP carrier board is a 6U VME bus card that provides an electrical and mechanical interface for four industry standard IP modules. The board provides full data access to the IP modules I/O, ID and memory spaces. The programmable registers are used for configuring and controlling the operation of IP modules.Each IP module supports two interrupt requests. The VME bus interrupt level is software programmable. The software configured interrupt modes are:a.Single level interrupt mode: All IP module interrupts can be mapped to a single VME bus interrupt level.
-
Product
Carrier Card
VIPC627-ET
-
VIPC627-ET is a 6U VME carrier card with four IP slots and extended temperature range. Two 50-pin, 0.1 inch flat ribbon cable connectors mounted in the front panel provide access to all IP I/O lines. Also, all I/O lines of 'IP D' are routed to VME P2 and 14 user selectable I/O lines of 'IP C' can be routed to VME P2 via a jumper field.
-
Product
6U VME Carrier for PMCs and PrPMCs
Ti4400
-
The Ti4400 is a 6U PMC/PrPMC carrier for VME systems and forms the basis of a flexible I/O system. The user can integrate two single PMC modules or one double-wide PMC.
-
Product
6U Dual 64/100 PMC VME Carrier
V2PMC2
-
The V2PMC2 PCI-X/PMC carrier card is a 6U VME that holds up to two single-width or one double-width PCI-X/PMC modules. The V2PMC2 works in association with a PCI-Express host which is connected to it through a x4 PCI-Express serial link onto P0 connector.
-
Product
PMC Carrier Module
DP-VME-5114
-
DP-VME-5114 is a VME-Based PMC Carrier Module. This 6U VME board PMC carrier can accommodate two PMCs. This board can be used for data acquisition, automated testing and checkout systems
-
Product
Carrier Boards
ROM-DB7500
Carrier Board
ROM-DB7500 is an Evaluation Carrier Board designed for Advantech's RISC Qseven module. It is compatible with the ROM-7420 Qseven module and provides a thorough environmentfor RISC module board evaluation. It supports wide range temperatures and 12V power input through AC/DC power adapter.
-
Product
PXI FPGA Module
FIO168
Carrier Board
Using OpenATE USB/PXI FPGA Carrier, you can develop your design to define custom I/O and control Hardware without prior knowledge PCI I/O and USB interface.
-
Product
Carrier Boards
ROM-DB7503
Carrier Board
ROM-DB7503 is the Referenced Carrier Board designed for Advantech's Qseven 2.1 module. It i provides a thorough environment for module board evaluation with its completefunction support. it's more easier for the end user to design portable devices by referring ROM-DB7503 design.
-
Product
Computer On Module
ITX-M-CC452-T10
Carrier Board
The ITX-M-CC452-T10 is an industrial Mini-ITX small form factor Type 10 reference carrier board designed to fully test WINSYSTEMS’ COMeT10-3900 COM Express Type 10 Mini module. The carrier board adheres to the PICMG COM Express specifications providing compatibility with other COM Express mini type 10 modules.
-
Product
3U CompactPCI Mini PCI, Mini PCIe Carrier Board
cPCI-3W10
Carrier Board
- Supports 32bit, 33/66MHz CompactPCI® bus- One SIM card socket- One Mini PCI and one Mini PCIe socket- PICMG® 2.0 R3.0 compliant
-
Product
M/MA Module Carrier
VX405C
Carrier Board
The VX405C carrier provides the mechanical and electrical interfaces between the VXIbus and up to six (6) VITA 12-1996 standard M/MA-Modules. The carrier provides VXI register configuration and access to the M/MA-Module I/O space and memory (if present). Each M/MA-Module is controlled separately and appears as a different logical address in the VXI environment. Over 100 M/MA-Modules are available that can provide custom interfacing to the unit under test (UUT). Up to six (6) unique interfaces may be provided in a single VXI slot.
-
Product
3U CompactPCI® Single 64-bit PMC Slot Carrier Board
cPCI-8301
Carrier Board
- PICMG® 2.0 32,64-bit/33,66 MHz cPCI bus- Supports one single-size 32,64-bit/33,66 MHz PMC site in 4HP width- Universal V(I/O) decided by backplane- Comprehensive EMC shielding
-
Product
COM Express Type 10 Reference Carrier Board
miniBASE-10R
Carrier Board
The COM Express approach of custom carrier combined with off the shelf system cores is an excellent solution when you need to customize but lack the time or quantity for a complete redesign. It fits most system integration projects with production volumes from 500 to 10,000 pcs per year. The COM Express concept has a great many advantages over full custom designs, it reduces engineering complexity, lowers the threshold for total project quantity and last but not least brings your product to the market in no time. The average time to design a carrier board is less than half the time of a full custom OEM board.
-
Product
3U CompactPCI® Serial XMC Module Carrier Blade
cPCI-A3XMC
Carrier Board
- 3U 4HP CPCI-S.0 peripheral- One XMC slot- Operating temperature: -40°C to 85°C with qualified components
-
Product
COM-HPC Client Type Reference Carrier Board in ATX Form Factor
COM-HPC Client Base
Carrier Board
The COM-HPC Client Base is an ATX size COM-HPC Client Type reference carrier board based on PICMG COM-HPC Revision 1.0. Together with the COM-HPC Client Type module of your choice and off the shelf add-on cards, you can quickly emulate the functionality of your desired end product for software development and hardware verification.
-
Product
SMARC 2.1 Reference Carrier Board with M.2 Extension
I-Pi SMARC Plus
Carrier Board
The I-Pi SMARC Plus is small (110mm x 110mm) SMARC reference carrier board based on SGeT SMARC (Smart Mobility ARChitecture) 2.1 hardware specification. Together with the SMARC short size module of your choice and off the shelf add-on cards, you can quickly emulate the functionality of your desired end product for software development and hardware verification.
-
Product
COM Express Type 6 evaluation carrier board
ATX-M-CC462-T6
Carrier Board
The ATX-M-CC462-T6 is a fully featured COM Express Type 6 evaluation carrier board designed for use with the WINSYSTEMS Intel® Tiger Lake UP3 COM Express and other COM Express Type 6 modules.
-
Product
6U CompactPCI Dual 64-bit PMC Slots Carrier Board
cPCI-8602
Carrier Board
- Supports two single-size 32,64-bit/33,66 MHz PMC sites in 4HP width- PICMG® 2.0 32,64-bit/33,66 MHz cPCI bus- PICMG® 2.1 Hot Swap Specification Compliant- 3.3V or 5V V(I/O) for cPCI bus and PMC sites- PLX® PCI-to PCI bridge PCI6154 for PCI bus- Power and HotSwap LED incidators on front panel
-
Product
Qseven® Reference Carrier Board
Q7-BASE
Carrier Board
Qseven is a Computer-on-Module (COM) standard for small sized and highly integrated systems adopted by SGET. The Qseven concept is an off-the-shelf, multi-vendor, Computer-on-Module that integrates all the core components of a common PC and is mounted onto an application specific carrier board. Qseven modules have a standardized form factor of 70 mm x 70 mm or 40 mm x 70 mm and have specified pinouts based on the high-speed MXM connector, regardless of the vendor. The Qseven module provides the functional requirements for an embedded application, which include, but are not limited to, graphics, audio, mass storage, network and multiple USB ports. A single ruggedized 230 pin MXM connector provides the carrier board interface to carry all the I/O signals to and from the Qseven module. This MXM connector is a well-known and proven high-speed signal interface connector that is commonly used for -PCI Express graphics cards in notebooks.
-
Product
Carrier Boards
ROM-DB7501
Carrier Board
ROM-DB7501 is an Referenced Carrier Board designed for Advantech's RISC Qseven 2.0 module. It i provides a thorough environment for module board evaluation with its completefunction support. It also supports 12V power input through AC/DC power adapter and with smart battery design, it's more easier for the end user to design portable devices by referring ROM-DB7501 design.
-
Product
ETX® Reference Carrier Board in ATX Form Factor
ETX-Proto
Carrier Board
The ETX-Proto is an ETX Reference Carrier Board in standard ATX form factor. Together with the ETX module of your choice and off-the-shelf add-on cards, you can quickly emulate the functionality of your desired end product for software development and hardware verification. The ETX concept has a great many advantages over full custom designs. It reduces engineering complexity, lowers the threshold for total project quantity and last but not least brings your product to the market in no time.
-
Product
Carrier Boards
ROM-DB5901
Carrier Board
ROM-DB5901 is an evaluation carrier board designed for the Advantech SMARC v2.0 module. It is compatible with the ROM-5720, ROM-5620 and ROM-5721 SMARC modules and has a multiple I/O interface for evaluation and development. It supports wide range operating temperatures, two power input interfaces, and two MIPI connectors for the camera module. ROM-DB5901 is an ideal development board for mobile applications, such as portable devices, industrial tablets or HMI systems
-
Product
Carriers
-
VadaTech carriers are available in a wide range of mezzanine styles and formats, including versions to enable you to adapt different buses and architectures. These carriers are designed to enable you to build a complete system using best-in-class building blocks or legacy products regardless of the form factor.
-
Product
VME Module
VME-4SIP
-
The new VME-4SIP Module provides a 6U high performance flexible I/O scheme, that supports industry standard Industry Packs. Choose from over a 100 different Industry Packs from Alphi Tech and others.
-
Product
Carrier Boards
ROM-DB5900
Carrier Board
ROM-DB5900 is an evaluation carrier board designed for the Advantech SMARC module. It is compatible with SMARC module ROM-5420 and has a rich I/O interface for evaluation and development. It supports wide range operating temperatures, two power input interfaces, and also supports two MIPI connectors for the camera module. ROM-DB5900 is an ideal development board for mobile applications, such as portable devices, industrial tablets or HMI systems.
-
Product
FPGA/FMC Carriers
-
Our AMC FPGA modules feature Altera Stratix IV, Altera Stratix V, Xilinx Virtex-5, Xilinx Virtex-6, Xilinx Zynq, Xilinx Artix, Xilinx Virtex-7 and Xilinx Kintex-7 FPGAs. We also offer a range of carriers that can accommodate standard FMCs featuring FPGAs from Altera and Xilinx, including the new Xilinx UltraScale family.
-
Product
VME
-
Highland Technology is a member of VITA, the VME standards body, and continues to release new technology into the VME market. As other bus architectures come and go, Highland remains confident that VME will maintain its position as the architecture of choice for essential, long life cycle programs.
-
Product
VME Extender
VME64-M
-
VECTOR Electronics and Technology, Inc.
Excellent performance with a multi layer design
-
Product
PCIe MiniCard Carrier
-
The PCIe MiniCard carrier offers four PCIe MiniCard sockets on a compact PCI/104 Express form factor board. All four sockets have PCIe x 1 and USB interfaces and support full size and half size PCIe MiniCard modules.
-
Product
Process Carrier Pallets
Metalic Family
-
Process carrier pallets to carry the circuit boards through pick-n-place, IR reflow, gold wire bonding, epoxy dot encapsulating, and final fuctional test. Test Electronics will precision drill and customize pallets for your circuit board. Click on the Quote tab on the left then click on the Carrier Pallets tab to get an instant quotation on your process carrier pallets. Process carrier pallets can be designed to carry your circuit boards through assembly, wash and final test.
