Voltage Amplifiers
See Also: Amplifiers, RF Amplifiers, Preamplifiers, Current Amplifiers, Audio Amplifiers, Transconductance Amplifiers, Op Amps, Klystron, Instrumentation Amplifiers, Distribution Amplifiers
-
Product
Replacement Power Amplifiers
-
Unholtz-Dickie offers a full line of high-performance Class D switching power amplifiers. These amplifiers, used in UD’s new shaker systems, are offered as replacements for older, water-cooled vacuum tube amplifiers or bipolar transistor amplifiers.
-
Product
Distribution Amplifier
-
AVLINK TECHNIC TAIWAN CO., LTD.
Is a device that accepts a single input signal and provides this same signal to multiple isolated outputs.These devices are important because they allow a signal to be distributed to multiple destinations without ground loops or signal degradation. They are used for a number of common engineering tasks, including multiple amplification, cable television, splitting monitor and front of house mixes, and "tapping" a signal prior to sending it through effects units to preserve a "dry" signal for later experimentation.
-
Product
High-Frequency Amplifiers
-
Tabor’s line of High-Frequency Amplifiers allows for a better, more advanced utilization of the already available digital outputs on some of Tabor’s arbitrary waveform generators.
-
Product
Power Amplifier
-
The Model LN power amplifiers offer extended output power, voltage capabilities, lowdistortion, versatility and the latest BJT power in the operational amplifier technology. All theseperformance features are not available in other power amplifiers.
-
Product
Power Amplifiers
-
Power Amplifier is used to amplify the output of the CS700A or CS701 signal generators. The 52 MHz bandwidth amplifier can swing 36Vpp with an output current up to 1A continuous. The CS1070 includes an internal inverting power supply to provide the negative rail, simplifying power supply requirements. The gain is fixed at x10 (20dB). The output voltage range is ±5V to ±18V and asymmetrical to +31, -5V for PSRR measurements right up to 30V as the input supply increases past 20V.
-
Product
RF Amplifier
SA801H
-
Hangzhou Softel Optic Co., Ltd.
SA801H indoor unidirectional user’s amplifier is special designed for the last “1km” of the CATV bidirectional transmission network. It adopts CATV dedicated RF modules (SOT-115 packaged), has good indexes, low power consumption, high reliability and excellent cost performance. It is suitable for the small and medium sized CATV transmission network.
-
Product
4-Quadrant Power Amplifier
PAV10000
-
PAV Series Four-quadrant Simulation Power Amplifier based on linear power amplifier technology and integrated advanced technical performance and rich functions.
-
Product
System Amplifier
-
Solid state Broadband Amplifiers are designed for optimum operation for IED Jammer Applications which is featured as below. We can rack mount any of our existing amplifiers or systems or custom design the amplifier and enclosure. Each Rack Mounted Amplifiers are built around a large bonded fit heat-sink rated for high temperature ambient operation.
-
Product
Voltage Detector
-
Shenzhen Noyafa Electronic CO.,LTD
*Detect AC Power range : 50-1000V.*Test live wire and with flash indicate.*Locate wire break point easily.*LED assist using in dark place.*Certification. Passes RoHS, FCC, and CE compliance testing, and Noyafa is certified to the ISO 9001 standard.*100% Affordable. Manufactured in China and a lot cheaper than competitor products with similar quality.
-
Product
Limiting Amplifiers
-
Teledyne Microwave Solutions (TMS) offer a range of Limiting Amplifiers which are used in instantaneous frequency and phase measurement receivers. The most important performance requirement of a limiting amplifier is to minimize output power variations, and provide a constant output over a wide input dynamic range.
-
Product
IEPE Signal Conditioning Amplifiers
-
Although IEPE (Integrated Electronics Piezoelectric) sensors is not a new technology there are a wide variety of applications where the measurement instrumentation is not configured with IEPE signal conditioning built in. In these situations it is necessary for the IEPE supply to be provided by an external source. Usually this type of instrument will also provide th user with the option to add gain to the signal being conditioned. The Kemo range of IEPE signal conditioning instruments can be used as stand alone conditioners/amplifiers are many of them can also be integrated with filters.
-
Product
RF Amplifier Modules
-
Analog Devices RF amplifier modules offer high linearity, low noise figures, and low phase noise, as well as low power consumption. These devices are all fully specified over frequency and temperature for use in a variety of applications.
-
Product
Voltage Meter
MDN8I
-
MDN8I is a mezzanine module designed for high-precision measurements in dynamic signal analysis systems, as well as for joint work with ICP sensors and vibration transducers with a charge output (force sensors, dynamic pressure, acoustic emission, vibration displacement, etc.). The MDN8I mezzanine module has electrical characteristics no worse than those of most foreign and domestic counterparts, and in some parameters exceeds them.
-
Product
High-end Cable DAC & Amplifier
Impacto universal
-
Beyerdynamic Digitalize high-end headphones.
-
Product
Voltage Transformer
-
Beijing GFUVE Electronics Co.,Ltd.
Are a parallel-connected type of instrument transformer. They are designed to present a negligible load to the supply being measured and have an accurate voltage ratio and phase relationship to enable accurate secondary connected metering.
-
Product
Narrowband RF/Microwave Power Amplifier
-
While our broadband amplifier series are designed for multi-purpose, narrowband amplifier series may provide more appropriate solution for your specific needs. By narrowing the frequency range, smaller, lighter amplifier solution at more reasonable cost will be usually available.
-
-
Product
RF POWER AMPLIFIERS
BLWA Series
-
A) RF-Sample PortsI) 3x 208 V AC / 60 HzB) External Dual Directional CouplerL) LAN Remote ControlC) IEEE-488.2 GPIB Remote ControlS) Internal RF Switching UnitD) Front Panel RF ConnectorsR) RS-232C Remote ControlE) RF Power Indication (digital)U) USB Remote ControlF) Gain AdjustmentW) Liquid CoolingH) DC SupplyX) External Control of other Amplifiers
-
Product
Voltage Testing
MicroDetect series
-
Hachmann Innovative Elektronik
Voltage detection simple and reliable with the MicroDetect line you get a type series of handy, exact and simply useable voltage detectors.
-
Product
Panel-mounted HIL Power Amplifier
PAC60Ci
-
PAC60Ci is the six-phase real time simulation amplifier, with maximum RMS phase current of 30A and maximum output power of 450VA. This current amplifier is possessed of high accuracy and fast liner response.
-
Product
Voltage Variation Simulator
KES7400A
-
The KES7400A Series comes in a single cabinet that consists of a Signal Generator module (including an arbitrary pulse generator), which combines our power supply technology and EMC technology, and a high-speed bipolar power supply module. Many automotive electronic devices have long wire harnesses and inductive load characteristics, as do motors, or capacitive load characteristics with a large-capacity capacitor connected between the input and ground. In the case of these devices, general DC power supplies exceed the linear operation range, potentially making it impossible to obtain the desired waveform output.
-
Product
Voltage Detector
LV-1
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
Using conductive rubber tip, free from short circuit. With slip stopper for the safety use.
-
Product
Traveling Wave Tube Amplifier
-
Skylink a leading provider in design and manufacture a wide range of traveling wave tube amplifiers(TWTAs) and microwave power modules(MPMs).Skylink's new generation of MPMs are based on a modular design, and use new technology, material and computer simulation system to improve weight, size and efficiency.Our main MPM series frequency covers range from 2 to 40GHz and providing more than 100W. They combine a helix TWT, a solid state amplifier and an integrated power conditioner in a compact package.
-
Product
Voltage Tester
EW005
-
Wenzhou Zhengyuan Electronic Co., Ltd.
Live and neutral wire identification
-
Product
RF Signal Amplifiers
-
The A10200 RF amplifier was designed to extend the power range of the Tabor arbitrary waveform generators and RF signal generators, yet it is compatible with many signal sources instruments.
-
Product
High Voltage Probe
HVP-15HF
-
*MAX.VOLTAGE:15KV DC.*BANDWIDTH:DC~50MHz.*DIVISION RATIO:X1000.*SIGNAL/NOISE:>60dB(1KHz)
-
Product
sbRIO-9264, Non-Enclosed, 25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module
781119-01
Voltage Output Module
Non-Enclosed, 25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module - The sbRIO‑9264 is a simultaneously updating analog output module that accommodates higher‑channel‑count systems. Higher density modules conserve chassis space, which leaves room for other measurement types. Each channel has its own digital‑to‑analog converter. The spring-terminal version of the sbRIO‑9264 uses a 36‑position connector for the output channels, and each channel has a ground connection. Non-enclosed modules are designed for OEM applications.
-
Product
NI-9264, 25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module
785190-01
Voltage Output Module
25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module - The NI‑9264 is a simultaneously updating analog output module that accommodates higher‑channel‑count systems. Higher density modules conserve chassis space, which leaves room for other measurement types. Each channel has its own digital‑to‑analog converter. The spring-terminal version of the NI‑9264 uses a 36‑position connector for the output channels, and each channel has a ground connection.
-
Product
Single-Ended to Differential Amplifiers
-
Analog Devices has developed a broad portfolio of single-ended to differential amplifiers that help designers meet their high performance requirements. ADI single-ended to differential amplifiers enable the processing of both single-ended inputs to complementary differential outputs or differential inputs to differential outputs. This provides a convenient solution when interfacing with analog-to-digital converters (ADCs). ADI also offers a series of differential receiver products that convert differential input signals to single-ended output.
-
Product
Voltage logger0 to 2.5V
TK-4703
-
Supplied with an input cable, this logger can measure voltages up to 2.5V DC and can be connected to many industry standard devices, such as CO2 sensors and current clamps, enabling the logging of a wide range of process parameters.The unit is particularly useful when space is at a premium.
