SFP
is a multi-source agreement (MSA) transceiver used in communicaitons.
See Also: SFP Test, SFP+, Transceivers
-
product
SFP / SFP+ Transceivers
Based upon unique technology developed and patented by OZC. Fiber optic data transport device – in an industry standard format (multi-source agreement – MSA – defined shape and functionality).
-
product
10 Gb/s SFP/SFP+ Evaluation Board
EV-SFP-171
The purpose of this SFP+ evaluation board is to provide the designer with a convenient means for evaluating SFP+ fiber optic transceiver such as 10 Gb/s(up to 16 Gb/s) SFP/SFP+ transceiver compliant with ANSI Fibre Channel FC‐PI‐5 for high speed electrical and optical specifications. This board provides SMA connectors for high speed TX and RX signals. The low speed control signals such as Tx_Fault, Rx_LOS and Rate_Selects can be controlled by using on board switches and test points. A connector for 2 wire serial interface to the module is also provided.
-
product
SFP+ Cable, 1m
784076-01
1-Pin, Male SFP+ to 1-Pin, Male SFP+ or 2-Pin, LC/LC Duplex to 2-Pin, LC/LC Duplex SFP Cable - The SFP+ Cable connects to the SFP port on some PXI High-Speed Serial Instruments, PXI Ethernet Interface Modules, Controllers for FlexRIO, and USRP RIO devices. The LC/LC Duplex model … has multimode and single-mode optical fiber options that you can use in tandem with SFP+ optical transceivers. The cable is rated for transmission speeds up to 10.3125 Gbps and is offered in different lengths.
-
product
Gigabit-SFP Transceivers
SFP Transceivers are designed for use in Gigabit Ethernet and to provide an IEEE-802.3z compliant link for 1.25/2.5Gbps short or long reach applications.
-
product
Test RTM with Ethernet SFP
VR300
Sundance Multiprocessor Technology Ltd.
The VR300 is a Test RTM, typically used during firmware and software development and debugging cycles on the VF360. The rear panel contains two mini-USB connectors, a Dual mini-SAS (SFF-8088) connector and a SFP case.
-
product
FMC Card with Four SFP+ 10 GBit Ports
TEF0008-02
Sundance Multiprocessor Technology Ltd.
The Trenz Electronic TEF0008 is a FPGA to Mezzanine Card (FMC) based on VITA 57.1 FMC HPC Standard, with four SFP+ 10 GBit ports for fiber optical SFP modules. It is inteded for use on a FMC HPC carrier and can not be used stand-alone.
-
product
SFP Module
F-3000
The DIAMOND flexos SFP modules (transceivers) make it possible to transfer data via fibre optics. The SFP modules are available for multi-mode and single-mode, Gigabit and Fast Ethernet. The SFPs have metal housings with latches for the simple removal of the module. They are compatible with connector types F-3000™ or LC.
-
product
Single Channel SFP+ All-In-One Sensitivity Tester
SFP+ Tester
All in one mainframe to perform a complete sensitivity test on a single channel fiber optic transceiver. Includes Clock source, BERT and all optical modules
-
product
AS5653 Compliant Small Form Pluggable (SFP) Transceiver
XCVR-AS5653
Avionics Interface Technologies
AS5653 SFP transceiver that can be inserted into any standard SFP slot - 1.0625 GBPS communication signals interface using TNC connectors - Bulkhead mountable female TNC connector at the end of a 1 meter length of RG179B/U - 100 feet of RG179 operates to better than 10E‐13 Bit Error Rate - Available for 75 Ohm single ended copper or 150 Ohm Differential
-
product
100BASE-T1 SFP Module
Art.-Nr.: TE-1430
Convert between 100BASE-T1 and Standard Ethernet The 100BASE-T1 SFP Module is the optimum solution to convert between 100BASE-T1 and SGMII. It fits into a standard Small Form-factor Pluggable (SFP) and generates 100 Mbit/s full-duplex 100BASE-T1.
-
product
1000BASE SFP Transceivers
CommFront offers a range of high-quality, high-performance SFP transceivers ranging from MM 850nm / 0.3 miles (550m) to SM 1550nm / 100 miles (160km). SFP (Small Form-Factor Pluggable) is a compact, hot-pluggable network interface module used for data communication and tele-communication applications. SFP equips with one or two fiber optic connectors (e.g. LC connectors) for connecting a fiber optic cable or sometimes an RJ45 connector for connecting a copper cable. Because of its compact size and flexibility, many Ethernet Switches come with SFP ports so individual ports can be equipped with any suitable type of transceiver as required.
-
product
COM Express Type 7 10GbE SFP+ Network Adapter Card
CEI-4x10G SFP+
- Support up to four 10GbE SFP+ interfaces- COM.0 R3.1 Type 7 compliant- Dedicated for Express-ID7
-
product
Compact Network Appliance Platform With Intel® Atom® Processor C3000 Family, Six GbE And Four SFP+ Ports
NA362 for vCPE
*Intel® Atom® processor C3000 family (Denverton)*Four DDR4 R-DIMM up to 128GB or U-DIMM up to 64GB memory*Six 10/100/1000 Mbps Ethernet ports and four SFP+ ports*Wi-Fi/3G/LTE through PCI Express Mini Card slot*Supports Intel® QuickAssist Technology*Supports Intel® Data Plane Development Kit (Intel® DPDK)*Suitable for VPN, vRouter, firewall and other vCPE applications
-
product
Bi-directional SFP Modules
BiDi SPF
The DIAMOND SA flexos BiDi-SFP modules (transceivers) make it possible to transfer data via fibre optics. The Bi-Di SFP modules are available in single-mode and Gigabit Ethernet. The SFPs have metal housings with latches for the simple removal of the module. They are compatible with connector types F-3000™ and LC.
-
product
SFP Based Fiber Optic Test Solution
Eye-BERT Micro
The Eye-BERT Micro is a low cost, easy to use, all-in-one SFP based fiber optic test solution offering high performance bit error rate testing at a fraction of the cost while providing a rich set of features not found in other bit error rate testers. Features include: variable bit rate, user programmable patterns, and optical power and temperature monitoring (per SFP capability). Additionally, with a click of a button, the Eye-BERT Micro will automatically test an SFP module based on the information it reads from the module and generate a detailed test report complete with manufacturer, part number, serial number, date code, fiber type, link length, speed, and test results. The Unit is supplied with anti-skid bumpers and is small enough to be integrated into larger systems for dedicated link verification.
-
product
COM Express Type 7 10GbE SFP+ Network Adapter Card
CEI-2x10G SFP+
- Support up to two 10GbE SFP+ interfaces- Inphi CS4227 inside- COM.0 R3.1 Type 7 compliant- Dedicated for Express-VR7
-
product
Gigabit Ethernet
CWDM SFP Transceivers
CWDM transceiver modules are offered at wavelengths from 1470nm to 1610nm and include LC connectors. These SFPs are 100% compatible with Cisco equipment.
-
product
Fibre Channel Test & Simulation Interface for PCI Express
PCIe-FC4
Avionics Interface Technologies
Half-size four lane PCIe board - Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speedsComprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent Analyzer - Supports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
product
Fibre Channel Test & Simulation Interface for PCI-X
PCI-X-FC4
Avionics Interface Technologies
Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Comprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent AnalyzerSupports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
product
Optical Fiber Transceivers
Optical Fiber Transceiver Module is a self-contained component that can both transmit and receive. Usually, it is inserted in devices such as routers or network interface cards which provide one or more transceiver module slot (e.g GBIC, SFP, XFP). Fiberinthebox provide a full range of optical transceivers, such as SFP+ (SFP Plus) transceiver, X2 transceiver, XENPAK transceiver, XFP transceiver, SFP (Mini GBIC) transceiver, GBIC transceiver, CWDM/DWDM transceiver, 40G QSFP+ & CFP, 3G-SDI video SFP, WDM Bi-Directional transceiver and PON transceiver.
-
product
PXIe-8238, 10 Gigabit PXI Ethernet Interface Module
784976-01
10 Gigabit PXI Ethernet Interface Module—The PXIe-8238 is a high-performance 10-Gigabit ethernet SFP+ interface for PXI Express based on the Intel 82599 10Gb ethernet controller. It includes two 10-Gigabit ethernet SFP+ ports in a single-slot PXI Express module and is compatible with both copper and fiber optic cabling.
-
-
product
Quickly & Accurately Validate Any Pluggable Transceiver from 10M to 100G
iOptics
iOptics offers a complete, powerful and easy-to-use tool for CFP and QSFP qualification and can validate the full range of low- to high-rate transceivers including SFP, SFP+, XFP, CFP, CFP2, CFP4, QSFP+ and QSFP28. iOptics offers a faster, streamlined and automated test sequence aimed at quickly and simply validating any type of 10M to 100G interface. It is the ideal solution for multirate field commissioning with a simple one-button pass/fail. It offers automated stress testing for lab qualification and is also ideally suited for data center and data center interconnect (DCI) testing.
-
product
Thermoelectric Cooler Controller
Analog Devices Thermoelectric Cooler Controllers work with cooler based photonics, offer the smallest size, the best efficiency and the most robust solutions. It has a linear power stage with the linear driver output and a pulse width modulation power stage with the SW output. Depending on the part number, it offers digital PID control or analog PID control or both. Our TEC controllers support a variety of MSA based optical modules such as SFP, SFP+,QSFP+, CFP/CFP-2/CFP-4 and QSFP28.
-
product
Fiber Tranceivers
Wuhan Sunma Technology Co., Ltd.
Active Optical Cables, Fiber Optic Transceiver Module is a self-contained component that can both transmit and receive. Usually, it is inserted in devices such as routers or network interface cards which provide one or more transceiver module slot (e.g GBIC, SFP, XFP).
-
product
1U Rackmount Network Appliance Platform With Intel® Xeon® Processor D-1527/ Pentium® Processor D1508 And 10 LANs
NA720
The NA720 is built on the server-class Intel® Xeon® D-1527 processor (codename: Broadwell-DE) and Pentium® processor D1508. The NA720 comes with two 10GbE SFP+ ports, eight Gigabit Ethernet ports and two expandable LAN modules supporting 1GbE/10GbE/Fiber/Copper/Bypass with a maximum of 26 LAN ports. Four DDR4-2400 MHz R-DIMM/U-DIMM sockets can provide system memory of up to 128GB and support both ECC and non-ECC memory types. For storage, it supports one mSATA and two 2.5” SATA hard disk drives. This high performance Intel® Broadwell-DE network appliance is an ideal solution for enterprise firewall, network bandwidth controller and UTM applications.
-
product
ARINC 664 Part 7 PXI Express Test & Simulation Instrument
PXIe-C664-V2
Avionics Interface Technologies
Supports IEEE 802.3 10/100/1000 Mbit/s Full-Duplex Ethernet links - Utilizes SFPs to support both copper and optical interfaces - Simulates multiple ARINC 664 End Systems - VL traffic shaping and input VL redundancy management - Supports up to 4K - Output VLs and 4K Input VLs - Supports up to 16K Sampling & Queuing output message ports and up to 16K input Sampling & Queuing message ports - ARINC 653, UDP, IP protocols managed onboard - IRIG-B time code encoder/decoder - Automatic message sequencing & periodic data generated onboard - Error Injection including Runt Frames, Short IFG, and Invalid MAC FCSDevice driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
Cyclone V based 6U cPCI COTS Module
iWave’s Cyclone V based 6U cPCI Card is a rugged standalone module complaint with 6U size CPCI PICMG 2.0 Rev 3.0 backplane, aimed for the high-speed data, video processing, and display applications. The card offer speed up to 512MB/s of DMA transfer and up to a 6 channels of transceiver interfaces capable of operating up to 6 Gbps, SFP, Built-in health monitoring circuits, DVI Input, and Output Interfaces
-
product
Pump Laser Diode Driver
S-110
•LD Driver, EDFA, ASE Broadband Source, 1X4 Optical Switch•Variable Optical Attenuator, Wavelength Meter•SOA Driver, SLED Driver, Pump LD Driver•Pattern Generator & BERT, SFP Transceiver Driver•4Channel Optical Return Loss Meter (Light Source & Power Meter)
-
product
Fibre Channel XMC Interface Module
XMC-FC4
Avionics Interface Technologies
Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Supports DMA for high speed streaming of data to/from the board - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent AnalyzerSupports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
