Sync
-
product
Sensor Monitoring
Networked Communication Solutions, LLC
Is a network monitoring and notification system synced with NCS wireless sensors.
-
product
Color Bar Generator
BL-CBG402-01N
The BL-CBG402 is a small (2 inch x 2 inch) RGBS Color Bar Generator designed for embedded and systems applications. It produces a split field SMPTE style color bar pattern and has either an external composite sync line of optional sync-on-green (set with an optional on-board DIP switch) Video timing is NTSC/EIA 60Hz field rate. The BL-SBG402 operates from a +5V regulated power source.
-
product
Color Pattern Generator
CG-971
* Analog video signal/Audio signal output * Conformity with NTSC,PAL,PAL-M and TNSC-4.43 * Selectable sync level * Available for various and output patterns by system file* Each staircase level in step pattern settable by voltage * Natural image and Monoscope pattern output * Max. 24 pattern installation * Auto sequence mode * GP-IB, RS-232C, and Digital IF (TTL) for remote control * Half rack size of 19 inch EIA 2U
-
product
Chip Test Adapter
RAMCHECK Sync
The RAMCHECK Sync Chip Adapter tests popular TSOP SDRAM memory chips in sizes of 16Mx16, 4Mx16, 32Mx8, 8Mx8, 64Mx4, 16Mx4 and more. Picture above shows the adapter with all optional sockets for 54, 50 and 44-pin.
-
product
Manual Oscillators
MOS-01, -01A
The MOS-01 manual oscillator module is used as a quality, general-purpose sinewave oscillator and digital readout monitoring system in the MAC-01, -02, or -03 AC Power Sources/Frequency Converters. The unit has guaranteed operating range of 20 HZ to 20 KHZ which is covered in three one-decade scales. The LCD digital metering system is switch-selectable to readout either frequency, voltage or current. A toggle switch selects the input for the attached AC Power Source/Frequency Converter to originate from the manual oscillator itself or from an external laboratory or programmable oscillator source. With oscillator mode switch in Internal position, the BNC connector delivers the signal to drive additional slave units or for oscilloscope sync or monitoring. BNC input/output is completely isolated with 1500 VAC breakdown and excellent common mode rejection. The oscillator modules must be factory installed and calibrated.
-
product
Pattern Generator
AVLINK TECHNIC TAIWAN CO., LTD.
* Intelligent functionality. * With 162 MHz pixel frequency. * Support total 38 timings. (up to UXGA) * Support Sync Type: H/V (TTL), SOG. * Low cost. * Single interface easily use. * Portable design, working time up to 8 hours by inside Re-chargeable battery. * Auto Power-off on Battery mode. * Provide total 34 patterns, Include: Color bar, Gray, Grid, Block¡K * By 16x2 Character LCD and key buttons, easily control.
-
product
Circuit Breaker Analyzer
CBAnalyzer
Simple operation requiring minimal trainingVery portable - it's a laptop or tablet pc running our Windows software programNo modification of the circuit breaker is requiredNo electrical connections are requiredRemoval of the circuit breaker from its mounting or cubicle is not requiredTesting can be performed during routine switchingData is easily transmitted over the internet to the users account where it is analyzed and compared with a known good profile (KGP) for that type of circuit breaker to determine: • Overall mechanical condition • Confirm maintenance intervals and lubrication • First trip testing data for arc flash compliance • Arc flash study validation checksPerform detailed analysis and store maintenance records using CBAnalyzer suite softwareAccess to the CBAnalyzer Account Manager which: • is where user accounts are created and each user's role is designated • provides access to your equipment database and test data archives • is where tests are synced • is where your equipment data is entered and stored • is required to use the CBAnalyzer software program
-
product
Digital/Analog Frequency Response Analyzer
8800 Series
The analyzer utilizes a digital “Sync” signal to provide synchronization between analog and digital hardware. The Model 8800 performs simultaneous analysis on both analog input channels and digital target processor, reliably capturing all data. Versatile by design, the Model 8800 digital interface can be disabled, via software, to use the analyzer in a standard 2-channel, analog-only configuration.
-
product
Dual Trace Oscilloscope
KM-20-10 / KM-20-20
Kusam Electrical Industries Limited
• Dual channels / dual traces, X-Y mode• 6” display, high brightness oscilloscope tube• High sensitivity triggering, upto 1mV / division clearer displaythan ordinary oscilloscope.• TV synchronous separation circuit to observe stable TV signal.• Triggering mode : AUTO / NORM / AV-V / AV-H• Vertical : ALT / CHOP / ADDX-x10 / Y-x5; Polarity reversal; CH1 Sync output• Power Supply : AC 220V ADN (110V optional)
-
product
Multi-Band Quad-Channel Receiver/Combiner, 4U Rack Mount System with Integral Tracking Receivers and Bit Syncs
LS-28-QRS
Lumistar offers the LS-28 series of high performance multi-band multi-mode RF Receiver/Combiners in several different versions including rack mount, portable and modular formats. Complete solutions from RF to bits and/or RF to UDP data broadcast in Chapter 10 format are available. Available at any frequency range from 215 MHz to 6000 MHz, data rates to 50 Mbps.
-
product
Corona Effect Camera
CoroCAM 8 UAV
*High-sensitivity UV detector, which can detect UVc light at 2.05×10-18 Watt/cm2, this allows detection of the smallest corona discharges.*9Hz (or 25Hz optional) IR radiometric camera module*Control of a limited number of camera functions from a standard RC controller using PWM or SBUS.*Remote control of all camera functions from the laptop via an Ethernet link.*Soft sync or staggered zoom of the 3 channel cameras. The IR and UV channels are digitally zoomed in, which is visible...optically zoomed in to the minimum FOV, and then digitally zoomed out.
-
product
Test Pattern Generator Delay & AV Sync Analyzer
VQDM-100
Versatile compact and robust multi-purpose tool for R&D and glass-to-glass QA/QC Instant visual-aural quality estimation plus automatic latency, AV sync and 3D LR sync measurement Multi-channel time-line analysis, including video frames continuity testing 4 Light Sensors with vacuum caps, 4 Audio inputs (standard line levels) 2 channels of AV timing analysis, simultaneous measurements of Video and Audio Latencies Real time multi-channel data acquisition via USB port Unique sophisticated set of static and dynamic test patterns up to 1080p@60fps - see more details in separate VQL page Source of VQDM, VQMA2, and VQMA3 Test Patterns for VideoQ Analyzers Multi-format digital and analog AV outputs: HDMI, YPrPb, S-video, SPDIF, LR analog audio Networkable unit, easy expansion with any external USB storage device: live clips, user content, etc.
-
product
IDM+
Multi-functional fault recorder including: -- Disturbance fault record (DFR)- Dynamic disturbance recording (DDR) - Phasor measurement unit (PMU C37-118)- Power Quality (PQ Class A)- Travelling wave fault location (TWS to +/-60m) - Impedance fault location- Protocols (61850, Modbus, DNP3) - Sequence of event recording (SOE)- GPS, IRIG and NTP time sync- iQ+ masterstation software.
-
product
1U 19” Edge Server With 4th Gen Intel® Xeon® Processor Scalable Family Processor
MECS-7120
- 1U 19” Edge Server with 4th Gen Intel® Xeon® Processor Scalable Family Processor- 6x DDR5 DIMMs, 4800MT/s (6 channels, 1DPC)- On-board 2x 25G SFP28 Ethernet ports- 1U 19’’ rackmount form factor for telecom infrastructure deployment- RunBMC with AST2600, IPMI v2.0/Redfish compliant- Optional clock module to provide time sync from GNSS- Designed for 5G: DU, DU+CU, DU+CU+MEC, MEC, uCPE, industrial edge computing
-
product
802.11ac wireless access point
AP-500AC
AP-500AC is a dual band 802.11ac wireless access point that delivers speeds of up to 1.3 Gbps targeted to support high-bandwidth activities such as video conferencing and cloud storage syncing. With speeds up to 4 times faster than 802.11n, it offers increased productivity for high density applications. AP-500AC can operate on both the 5GHz and 2.4GHz frequency bands simultaneously.
-
product
LED synchroscope
LS-110 SYNC (110V, 120V, 220V, 230V, 240V)
Standard Electric Works Co., Ltd
• Input Voltage : 110V AC, 120V AC, 220V AC, 230V AC or 240V AC.• Standard 4.5-inch switchboard case.• Front panel mount.• 3 bi-colored LED indicators for "SYNC", "GEN" and "BUS".• 24 LEDs in a circle display the phase angle and the frequency differences between 2 networks.• 360° LED indication.• 12 o'clock position LED is bi-colored.
-
product
PTP Toolbox
OSA 5410/11
The OSA 5410 Series is a family of compact and cost-effective synchronization distribution and assurance devices that bring the power of Syncjack™ to any network. Following a toolbox approach, the family members of the OSA 5410 Series can be utilized in a variety of network synchronization applications including IEEE 1588v2 Access Grandmaster, Boundary and Slave Clock, GNSS receiver and Primary Reference Time Clock (PRTC), synchronization signal conversion and sync probe applications.
-
product
Telemetry Transmitter for FM with up to 3 Bands
LS-11-F
The LS-11-F portable FM test transmitter is designed for checkout and troubleshooting of telemetry receiving systems operating with FM modulation. For applications with any of the ARTM modulations (Tier 0, Tier I, or Tier II), please refer to the LS-11-M Data Sheet. Complete ground stations including the antenna with LNA, RF down-converter, IF receiver, bit synchronizer, and PCM decommutator can be tested and bit error tests performed. The design allows secure links to be tested with an external encryptor. The Test Transmitter contains an internal PCM Data Simulator and Pseudorandom patterngenerator that operates in a BERT mode. The device provides simulated clock and data (without transmitter enabled) and accepts external data for modulating the internal transmitter. Complete setup can be achieved locally through the keypad and two-line LCD display or remotely through the USB Interface. Operational parameters include the PCM format parameter database information (frame sync patterns, wavewords, etc…), pre-modulation filter selection, transmitter carrier frequency, transmitter deviation, and output power level. Output power can be selected from approx. -60 to +5 dBm in 5 dB steps. The Test Transmitter contains a LiFePO4 Battery (Lithium Iron Phosphate), which provides higher energy density at ¼ the weight of legacy lead-acid batteries. The unit also provides an internal battery charger and will operate for up to twelve hours on battery power having received on a full charge.
-
product
Clock Generator
CG-1800
A video sync / master clock generator that can build a flexible high-quality sound synchronization system.
-
product
3 Channel Sync/Async Serial Interface PCI Mini Card
TMPE863
The TMPE863 is a standard full PCI Express Mini Card, providing three high speed serial data communication channels.
-
product
In-Circuit Testing and Test Engineering
GenRad 2287
3560 Hybrid Test NodesWindows InterfaceTotal GenRad 227X Migration Capability20 Mhz Clock, Sync, and Trigger, 5 Mhz data ratesVector Test for VLSI, PLCC’s & ASICSTest Express Vectorless TestingMultiple Chain Boundary ScanAnalog Functional Test Module
-
product
LED Synchroscope
LS-96 SYNC
Standard Electric Works Co., Ltd
● Input Voltage : 110V AC, 120V AC, 220V AC, 230V AC or 240V AC.● Square shape panel 96 x 96mm● 3 bi-colored LED indicators for "SYNC", "GEN" and "BUS"● 24 LEDs in a circle display the phase angle and the frequency differences between 2 networks● 360° indication● 12 o'clock position LED is bi-colored● PC window, ABS resin frame, PC case
-
product
Sync Generator
LT 4610
The LT 4610 is 1RU full-rack size sync signal generator that can output triple-rate SDI (3G-SDI/HD-SDI/SD-SDI) signals. It employs two power supply units for redundant operation to protect against power supply failures. The genlock function for external sync signals enables SDI signals, six sets of analog black burst sync signals, and audio word-clock signals to be output synchronously. The genlock function is equipped with a STAY IN SYNC function that maintains the phase when errors occur in the input signal, making it possible to provide stable sync systems.In addition to test pattern output including color bars and SDI check fields, the LT 4610 can embed ID characters, QVGA logo marks, safety area markers, and embedded audio in a SDI signal output.
-
product
1-Channel 3.6 GHz or 2-Channel 1.8 GHz 12-bit A/D with DDC - XMC
Model 71641
- Ideal radar and software radio interface solution- One-channel mode with 3.6 GHz, 12-bit A/D- Two-channel mode with 1.8 GHz, 12-bit A/Ds- Programmable one- or two- channel DDC (Digital Downconverter- 2 GB of DDR3 SDRAM- Sync bus for multimodule synchronization- PCI Express Gen. 2 interface x8 wide- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Clock up to four modules with Model 7194 High-Speed Clock Generator - PMC/XMC- Synchronize up to four modules with Model 7192 System Synchronization and Distribution Amplifier - PMC/XMC- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
product
1U Quad Bit Sync for Data Rates up to 40 Mbps
LS-44-QBS
The LS-44-QBS contains up to 4 Lumistar LS-40-DB25 Bit Synchronizer Daughterboards in a 1U RackMount chassis with status lights on the front panel and all interconnections through the rear. The design contains an internal computer which runsoff DOS or Windows depending on the version selected. The DOS version boots quickly without the delays required for Windows startup. The Windows version offers networking. The unit can be connected directly to the optional 1U slideout keyboard/display, for setup resulting in only 2U of total rack height. For applications that require many bit synchronizers, a 1U keyboard/Display with KVM switch allows 32 bit synchronizers in 9U of rack height. When power is applied, the computer will operate with the last configuration unless the operator wishes to change the setup. For setup, the keyboard/display is pulled out and the display is flipped up to monitor the process. When the bit synchronizer setup is completed, the keyboard/display canbe closed up since the status can be monitored on the front panel without an external display.
-
product
300W - Single Output
i7C Series
*Wide 1/16th Brick Footprint*9-36 Vdc, 9-53 Vdc Input*5-28, 8-24, 9.6-48 Vdc Outputs*Non-Isolated Step Up/Step Down*-40 to 125 °C Operating Temperature*Openframe, Baseplate or Heatsink options*Trim, On/Off, Power Good, Sync, Imon
-
product
1-Chan 3.6 GHz or 2-Chan 1.8 GHz 12-bit A/D with Virtex-6 FPGA - 3U VPX
Model 52640
- Ideal radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- One-channel mode with 3.6 GHz, 12-bit A/D- Two-channel mode with 1.8 GHz, 12-bit A/Ds- 2 GB of DDR3 SDRAM- Sync bus for multiboard synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- 3U VPX form factor provides a compact, rugged platform- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
product
Automatic Audio-Video Sync Detection
BATON® LipSync
BATON® LipSync is an automated tool for lip sync detection and verification. BATON LipSync leverages image processing and machine learning (ML) technology and deep neural networks to automatically detect audio and video sync errors. Using BATON LipSync, broadcasters and service providers can accurately detect audio lead and lag issues in media content in order to provide a superior quality of experience (QoE) to viewers.
-
product
Chassis
United Electronic Industries, Inc.
Two independent Gigabit (1000/100/10Base-T) Ethernet InterfacesOne port for Control, the second for diagnostics orBoth ports bonded/teamed for redundant network accessCompact: 2.7" x 4" x 4.1"Over 60 different I/O configurationsRugged: 100 g shock, 5 g Vibration, −40 to +70 °C, 0 – 70,000 feetReal-time: 1000 I/O scans in < 1 millisecondInter-device sync interface
-
product
Laser Controllers
The laser controllers provide a simple method of controlling Lumina and other popular laser diode drivers or full laser systems. They include the ability to easily control current levels, pulse modes, and interlock controls as well as monitor voltage and current levels as well as q-switch triggering, external triggering, sync output, and additional I/O signals.
