Filter Results By:
Products
Applications
Manufacturers
Test Fixtures
UUT interconnect interchangeable with tester.
See Also: Fixtures, Mechanical Fixtures, Vacuum Fixtures, ATE Fixtures, PCB Test Fixtures, Board Test Fixtures, Bed of Nails, Spring Probes, Test Jigs, Test Probes
-
product
6TL08 Benchtop Test Platform
H710008
The 6TL-08 base platform was designed to cover the most common testing and in-system programming (ISP) needs with a reduced initial budget. The system includes a robust manual linear push mechanism allowing a low-cost fixture strategy thanks to the exchangeable cassettesThe platform enclosure features an 8-Slot fixture receiver, compatible with VPC 90 Series Mass Interconnect Module, as well as 6TL intelligent YAVModules (YAV90MMU &YAV90059), with room for fast ISP devices, optional PXI chassis and various power supplies. A removable back panel allows easy placement of custom connectors or test auxiliary circuitry.
-
product
Emergency Battery Test Fixture
TA-60
This test fixture will allow servicing of the 60-1321-( ) series of emergency exit light power supply. These supplies are used in many aircraft to annunciate exit lighting when aircraft power failure occurs. The TA-60 test fixture is equivalent to the suggested test fixture in the OEM 60-1321 CMM. The four load lamps are conveniently placed behind an acrylic red lens for proper viewing while performing load test. The bench cable is provided as part of the test fixture.
-
product
Automatic Test Equipment Machinery
Is used to assist wiring fixtures and then test the fixtures for wiring errors. We also can manufacture and/or design custom machinery to your specifications.
-
product
Turn-Key Functional / Mechanical Fixture
In addition to In-circuit testing, functional testing is widely used in the industry to verify electronic cards. This is why ReMaTek has always paid a special attention to the specific requirements of functional testing. Our dedicated engineering staff is prepared to handle all of your mechanical, electrical and software requirements. We are aiming particularly the small turn-key test systems where all the elements; the mechanical fixture, the test equipment and the test software, are put together in a complete system.
-
product
Flying Probe PCB Test and Repair System
GRS500
Designed to help troubleshoot complex boards when fixture based tools are not a viable solution, the GRS500 is designed to help you compare the characteristics of good and faulty PCBs, using nodal impedance test, and a "Videosection" technique which presents you with high resolution images of a good board for use in live video comparison with the board under test,
-
product
High Node Count In-Circuit Test Fixtures
HNC Test Fixture
Circuit Check continues to be a leading edge provider of custom engineered test solutions with our new Keysight i3070 HNC test fixture. Working with Keysight Technologies during the development of their HNC adapter in 2011, we were the first test fixture provider to offer customers with a solution to test large node count boards. High node count test fixtures can handle greater than 10,000 probes.
-
product
Low Noise Test Leads For N1413 With B2980 Series, 1.5m
N1425A
The N1425A is designed to operate specifically with the B2985B/87B. It can hold DUTs with large terminals being used with the N1426C. The N1426A with the N1425A is available for measurements of small DUTs such as PC boards or IC sockets. The N1426B with the N1425A enables the construction of simple custom-made test leads. The N1413A High Resistance Meter Fixture Adapter is also required to connect the N1425A to the B2985B/87B.
-
product
Shield Boxes
Concentric Technology Solutions, Inc.
CTS can provide a customized integrated RF Shield Box or RF Enclosure Test Solution for manual or automatic testing at an off-the-shelf solution price. Many companies make RF Shield boxes, RF Enclosures or DUT fixtures, but only CTS bridges the gap by providing a complete integrated RF Shield Box or RF Enclosure testing solution for providing the RF shielding needed for repeatability within your budget and schedule.
-
product
Actuation Methods for Functional Test Systems
Functional test typically applies full operational power to a final product or a loaded printed circuit board in order to determine if the Product/ PCB performs functions as designed. This type of test often involves custom built test equipment and custom test fixturing. Circuit Check supports all forms of functional test strategies within its Signature Series functional test fixtures.
-
product
MECHANICAL TEST FIXTURE KITS
TX-MT-SERIES
Test-X MT Series mechanical kits are an affordable solution to printed circuit board testing. With multiple configurations and available options, this product is sure to meet your testing needs. The MT Series features a hinged 3/8" FR4 probe plate, tooling holes for accurate drilling, and side handles for easy transportation.
-
product
Manual Test System for ICT & ISP with Integrated ABex and up to 426 Test Points
LEON Fixture
The LEONFixture is the ideal ICT and ISP solution for small and cost sensitive applications. This manually operated test system combines optimal ergonomics with high performance, durability and precision, ensuring your investment over the long term. The LEONFixture features a test system integrated in a manual base fixture. The system is designed to be used with an Ingun ATS MA13 insert which could be customized by a lot of fixture houses all over the world.As part of the LEON Family, LEONFixture is based on the ABex platform which directly incorporates Konrad analog bus technology and PXI/PXIe in one chassis.
-
product
Adhesion and Peel Tester
Test package for combination module adhesion/peel tester includes a motorized test stand, digital force gauge, AC adapter/charger for 115VAC or 230VAC, data acquisition and exporting software, scoring fixture, glue fixture and necessary attachments and cables to perform the above tests.
-
product
Life Cyclic Durability Testing
Environment Associates can provide everything you need for cyclic durability testing and performance fixturing. Services include mechanical cycling to a position or load, fatigue cycling to a fixed load, rotational torque cycling, and simple push/pull cycling. EA can design your fixture with electro-dynamic, air, or hydraulic assistance to mechanically move your part. All of our fixtures can be manufactured to withstand a wide range of temperature, humidity and vibration inputs. If required, forces can be monitored electronically, using a wide variety of inputs (i.e. strain gages, load cells, rotational transducers, thermocouples, shunts, and more). EA can create holding and check fixtures to perform “pre” and “post” evaluation for dimensional issues that may occur during testing. EA can provide fixtures for single tests run internally for EA test labs and can manufacture fixtures to be purchased directly by the customer for their internal use.
-
product
Spectrum Analysis For E5081A Up To 44 GHz
S960907B
The Keysight S960907B spectrum analyzer (SA) software application adds high-performance microwave spectrum analysis capabilities to the Keysight ENA-X up to 44 GHz. With fast stepped-FFT sweeps resulting from optimized data processing, the SA application provides quick spurious searches over broad frequency ranges. Conduct simultaneous spectrum measurements using test and reference receivers. For efficient measurements of spurious signals emanating from mixers and frequency converters, combine the multi-channel SA with the internal swept-signal generators. The SA application employs source-power and receiver-response calibration as well as fixture de-embedding, providing in-fixture and on-wafer spectrum measurements with the highest level of accuracy.
-
product
Functional Test
UTS
The UTS functional test system is perfect for electronics manufacturing operations that have a mix of products where operators load and unload devices under test (DUT) and routinely change out fixtures for each type of DUT.
-
product
Bench Mounted Tester
Flex 10
The Flex 10 bench mounted ATE is the smallest ‘standard’ tester in our range. The system comprises a single unit, measuring 600mm x 360mm x 660mm. A VPC S6 interface is normally used on this system allowing multiple test fixtures to be used with the system.
-
product
PC Based Test Setup for LED PCB of Luminaire
The panel carries out different tests one by one and provides indication of the Test results as OK or NOT-OK. It is very useful and handy in line testing on Mass production line as well as type Testing. Special fixture can be provided for the specific product. This avoids the connections & disconnections of the product for different tests. The total time for entire testing is less than 40 seconds.
-
product
Actuation Methods for In-Circuit Test Fixtures
Commonly referred to as In-Circuit Test (ICT), loaded board test can be defined as the task of measuring values of components that have been installed on a printed circuit board (PCB). A second basic category of loaded board test measures simple open and shorts on the board to verify manufacturability standards. Circuit Check supports all forms of in-circuit test strategies with its Performance Grade and Value Line test fixtures.
-
product
Material Test Machines
Sanwood Environmental Chambers Co ., Ltd.
Sanwood Universal Test Machines, UTM, are widely use for different material testing, like semi-product & finished product made of rubber, plastic, metal, nylon, non-woven fabrics, textile, tape, polyfoam, waterproof materials, wire, cable, etc. With different test jigs or fixtures, the UTM can run the tensile, compression, shearing foce, adhesion, peeling force, tear strength, fatigue, etc test according to GB, CNS, ASTM, ISO, DIN, JIS, EN test standards.
-
-
product
µHELIX® Test Probes
Series S200, S300, S400, and S500
Test Probes for fine-pitch applications: CSP, BGA, SiP, SoC, flex-circuits, micro pcb, sub-mm center-to-center spacing, half mm, quarter mm spacing. Excellent for use in sockets, fixtures, and contactors for semiconductor testing and in coaxial installations.
-
product
Stand-Alone Test Fixture
MA 2012/D/H/GR2270/71
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: NoInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 17,00 kg
-
product
ADI Test Fixture
TA-6500
The TA-6500 test fixture combines the features of the OEM's Instrument Servo Tester(T307962), the Pointer/Flag Test Fixture(T307951) and the AD-650/600 Test Panel(T334043) all into one panel to facilitate testing of these Attitude Director Indicator's. The panel switches and adjustment pots are labeled to match the test procedure numbers and the duplicity in marking makes it easier for the technician to understand each function. The UUT interface is through a 96 pin zero insertion force(ZIF) type connector to minimize contact wear. The expanded localizer and nav input pins J2-34/35 are exposed on the panel to facilitate the insertion of a 200 ohm shunt when required. The fixtures rear panel has connectors for the required dual API/Synchro transmitter interface while the panel switches provide the correct routing of each.
-
product
CableEye® HV-Rated QuickMount™ Housing for CAMI Connector Boards
CBH2
CAMI Research Inc. (Acton, MA) has released a High-Voltage (HV)-rated QuickMount housing (CBH2) for its CableEye® automation-ready, cable and wire harness testing systems. As a free-standing, quick-release board fixture, it allows users to connect CAMI’s test interface boards to the 64-pin headers of any expansion module - even at some distance. The housing may be used with any CableEye model and is rated to 2100 Vdc / 1500 Vac.
-
product
In-Circuit Tester
Eagle MTS180
The Eagle offers low testing cost for high volume with even the most complex fixture applications. Equipped with a Press-Down-Unit and a combination of analog and hybrid In-Circuit test pins, the MTS180 is in a class for its own. Furthermore, the tester can be equipped with functional test modules to provide even higher fault coverage and thus satisfy the test requirements of a larger number of customers.
-
product
PhyView Analyzer
The PhyView Analyzer dramatically simplifies the task of Ethernet 10/100/1000 interface testing in finished products without the need for test fixtures, test signals, scopes, and probes.
-
product
In-Circuit Test Applications
With decades of experience developing test fixtures, we are the recognized industry leaders for solid and reliable quality as well as our outstanding customer service. We fully support our products locally and worldwide for maintenance, repair, and ECO work. Also, 100% wiring verification is part of our Quality Control process, by utilizing automated verification machines for GenRad/Teradyne and HP/Agilent fixture.
-
product
Standalone Test System
1000 Series ATE
The Circuit Check 1000 Series ATE provides a configurable standard platform that can utilize multiple mass interconnect interfaces while providing ease of maintenance and the ability to accept a wide variety of test fixture solutions. With the 1000 Series ATE, test procedures become automatic, with test steps and go/no-go limits easily programmable.
-
product
Magnetic Material Test Fixture
16454A
The 16454A is designed for accurate permeability measurements of toroidal-shaped magnetic materials. Since the construction of this fixture creates one turn around the toroid (with no magnetic flux leakage), the need of winding a wire around the toroid is unnecessary. Complex permeability is calculated from the inductance with and without the toroid. When the E4991A/4291B with option 002 is used as the measurement instrument, direct readouts of complex permeability are possible. In addition, it is furnished with a small and a large fixture to adapt to a wide range of sizes.
-
product
6TL23 Off-Line Seat Operation Base Test Platform
H71002300
The 6TL23 is a bare rack for creating Off-Line, modular, flexible and reliable Base test platforms. The overall rack capacity is 18U (580mm depth). The rack is ideal for sit-down operation, since there’s space for the operator’s legs under the fixture receiver.
