Synchronizers
See Also: Synchronization
-
Product
IRIG Time Code Receiver & Generator for Computers (PCI Express)
TCR180PEX
-
Meinberg Funkuhren GmbH & Co. KG
The TCR180PEX receives IRIG-A/B/G, IEEE 1344, IEEE C37.118 or AFNOR NF S87-500 time codes and can be used for synchronizing the system time of its host PC. The IRIG output of this card can generate an IRIG signal for other IRIG time code readers. The output format is independent from the incoming IRIG signal - a perfect solution to your IRIG conversion requirements. It is used in applications like data acquisition, standalone computer time synchronization (for systems without a network connection or higher accuracy requirements) or as an IRIG converter device.
-
Product
PCIe 16 Bit Arbitrary Waveform Generator - up to 125 MS/s on 4 Channels
M2P.6566-X4
Arbitrary Waveform Generator
The M2p.65xx series offers different versions of arbitrary waveform generators for PCI Express with a maximum output rate of 125 MS/s. These boards allow to generate freely definable waveforms on several channels synchronously. With one of the synchronization options the setup of synchronous multi channel systems is possible as well as the combination of arbitrary waveform generator with digitizers of the M2p product family. The 512 MSample on-board memory can be used as arbitrary waveform storage or as a FIFO buffer continuously stream data via the PCIe interface. Importantly, the high-resolution 16-bit DACs deliver four times the resolution than AWGs using older 14-bit technology.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit High Speed Digitizer - 180 MS/s on 20 Channels, 20 Single-Ended Inputs
DN6.447-20
Digitizer
The digitizerNETBOX DN6.44x series allows recording of up to 24 synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
Product
PXI Oscilloscope 2 Channel, 250Msa/s
PXI‑5114
Oscilloscope
The cost-optimized PXI‑5114 oscilloscope has two channels with flexible settings for coupling, impedance, voltage range, and filtering. PXI oscilloscopes also offer a variety of trigger options, large onboard memory, and a device driver that includes streaming and analysis capabilities. The device is particularly suitable for applications with fast signals that require flexible measurement configurations and an analog bandwidth of up to 125 MHz. The PXI‑5114 also features PXI‑based synchronization and data streaming capabilities.
-
Product
Arbitrary Waveform Generator
HDAWG
-
The Zurich Instruments HDAWG multi-channel Arbitrary Waveform Generator (AWG) has the highest channel density available in its class and is designed for advanced signal generation up to 750 MHz bandwidth. The HDAWG comes with either 4 or 8 DC-coupled, single-ended analog output channels with 16 bit vertical resolution. The outputs can be individually switched between a direct mode, with maximized bandwidth and superior noise performance, and an amplified mode, that boosts the signal amplitude to a maximum of 5 Vpp. With 2 markers per channel precise setup synchronization is guaranteed while the full 16 bit output resolution is maintained.
-
Product
PXIe-6386, 8 AI (16-Bit, 14 MS/s/ch), 2 AO, 24 DIO, PXI Multifunction I/O Module
785926-01
Multifunction I/O
PXIe, 8 AI (16-Bit, 14 MS/s/ch), 2 AO, 24 DIO, PXI Multifunction I/O Module - The PXIe-6386 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, four 32‑bit counters, and analog and digital triggering. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PXIe-6386 is ideal for a variety of applications, such as IF digitization; transient recording; ISDN, ADSL, and POTS manufacturing test in the telecom industry; ultrasound and sonar testing; and high-energy physics. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
3-Ch 200 MHz A/D with DDC & 2-Ch 800 MHz D/A with DUC, Virtex-7 FPGA - XMC
Model 71721
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Three 200 MHz 16-bit A/Ds- Three multiband DDCs (digital downconverters)- Two 800 MHz 16-bit D/As- One DUC (digital upconverter)- Multiboard programmable beamformer- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- VITA 42.0 XMC compatible with switched fabric interfaces- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Ultra Multi-Channel Battery Emulator
-
Peritec Ultra Multi-Channel Battery Emulator is used for the development of electric car(EV). The hardware has great extendability, it can also simulates up to 192ch synchronized DC power supply with high isolation and you can make the test sequence with Mirosoft Excel.It can be used as a power source such as a simulator of new energy development for the evaluation. In addition, we can correspond flexibly to customize provide the best solution to suit the needs of our customers.
-
Product
3-Channel 200 MHz A/D and 2-Channel 800 MHz D/A with Virtex-6 FPGA - PCIe
Model 78620
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Three 200 MHz 16-bit A/Ds- One digital upconverter- Two 800 MHz 16-bit D/As- Up to 2 GB of DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- PCI Express (Gen. 1 & 2) interface up to x8 wide- Optional user-configurable gigabit serial interface- LVDS connections to the Virtex-6 FPGA for custom I/O- RoHS Compliant Lead-Free Version Available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit High Speed Digitizer - 180 MS/s on 2 Channels, 2 Single-Ended Inputs
DN2.447-02
Digitizer
The digitizerNETBOX DN2.44x series allows recording of one, two, four or eight synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
Product
Field Ttesters
-
Our product range comprises from small handheld, battery fed testers to full featured service performance assurance tools and distributed monitoring systems. We have several product lines including:QoS / SLA verification system Ethernet, IP, Critical Data, VoIP, IPTV .Hand-held testers: Gigabit Ethernet, Synchronous Ethernet, E1, PDH, SDH, Ethernet, IP, Jitter, Wander, Datacom, Frame Relay, etc.
-
Product
640 Gb/s Digital Signal Processor
M8132A
Digital Signal Process
The M8132A is a powerful digital signal processing module featuring two customers accessible Xilinx Ultrascale+ FPGAs, four optical data interfaces (ODI) running at up to 160 Gb/s in+out each, and a PCIe Gen3 x8 link to the AXIe backplane. In addition, the module provides a trigger input and output, synchronization input and outputs for deterministic latency between compatible digitizers and AWG modules as well as a 10-general purpose I/O pins. The M8132A is part of Keysight’s Wideband Solution Platform that consists of a portfolio of compatible instruments, including digitizer, arbitrary waveform generator, digital signal processor and storage modules.
-
Product
NI-5791, 200 MHz to 4.4 GHz RF Adapter Module For FlexRIO
782510-01
RF Adapter Module
The NI‑5791 provides continuous frequency coverage from 200 MHz to 4.4 GHz. It features a single-stage, direct conversion architecture that provides high bandwidth in the small form factor of a FlexRIO adapter module. The onboard synthesizer, which is the local oscillator (LO), sets the center frequency for acquisition and generation, and you can export it to other modules for multiple input, multiple output (MIMO) synchronization. You can also import the LO from an external connector, enabling synchronization of up to eight NI‑5791 modules. For higher frequencies or a greater number of devices, you can use an external LO distribution amplifier.
-
Product
8-Channel 200 MHz A/D with DDC, Virtex-7 FPGA - 6U VPX
Model 58761
-
- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Four or eight 200 MHz 16-bit A/Ds- Four or eight multiband DDCs- Multiboard programmable beamformer- 4 or 8 GB of DDR3 SDRAM- PCI Express (Gen. 1, 2 & 3) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus formultimodule synchronization- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
3-Ch 200 MHz A/D with DDC & 2-Ch 800 MHz D/A with DUC, Kintex UltraScale - XMC
Model 71821
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Exceptional dynamic range and analog signal integrity- Xilinx® Kintex® UltraScale" FPGA- Three 200 MHz 16-bit A/Ds- Three multiband DDCs (digital downconverters)- One DUC (digital upconverter)- Two 800 MHz 16-bit D/As- 5 GB of 2400 MHz DDR4 SDRAM- Programmable frequency synthesized sample clock generator- Sample clock synchronization to an external system reference- Powerful DMA controllers for moving data- PCI Express (Gen. 1, 2 & 3) interface up to x8- Multi-channel synchronization with clock/sync bus- Optional clock/sync generator for multi-board systems- Optional LVDS port for custom FPGA I/O- Optional gigabit serial links for custom FPGA I/O- Ruggedized and conduction-cooled versions available- Navigator® BSP for software development- Navigator® FDK for custom IP development- SPARK® fully-integrated development system- Free lifetime applications support- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
-
Product
Ground Fault Protection Monitors
-
The Earth Fault Resistance Monitor (EFREM) and the Rotor Health Monitor (RHM) provide wireless rotor ground fault and temperature monitoring for generators and motors. The systems replace older slip ring contact ground fault detectors on any synchronous generator or motor.
-
Product
*PCIe-5785, 12-Bit, 6.4 GS/s, 2-Channel FlexRIO IF Transceiver Device
785589-01
FlexRIO IF Transceiver
The PCIe-5785 enables direct RF acquisition up to 6 GHz and generation up to 3 GHz with 12 bits of resolution. You can use it in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. The PCIe-5785 is ideal for applications that require wideband acquisition and generation with multichannel synchronization, including radar, electronic warfare, and communications. The FlexRIO driver includes support for acquiring and generating waveforms out of the box, and you can use the LabVIEW-programmable Xilinx Kintex UltraScale FPGA to implement custom algorithms for real-time signal processing.
-
Product
Power Conversion
-
The XRP6124 is a non synchronous step down (buck) controller for up to 5A point of loads. A wide 3V to 30V input voltage range allows for single supply operations from industry standard 3.3V, 5V, 12V and 24V power rails. With a proprietary Constant On-Time (COT) control scheme, the XRP6124 provides extremely fast line and load transient response while the operating frequency remains nearly constant. It requires no loop compensation hence simplifying circuit implementation and reducing overall component count. The XRP6124 also implements an emulated ESR circuitry allowing usage of ceramic output capacitors and insuring stable operations without the use of extra external components.
-
Product
Miniature Time Code Recorder
MTCR
-
When the distance is extreme or using a wireless microphone is not practical, the MTCR recorder can travel with your subject and capture professional quality audio, synchronized with timecode. It’s tiny size is unobtrusive and easily placed in garments and costumes, and easy to conceal when used as a “plant” microphone to capture environmental or location sound.
-
Product
DSP-Based 4/8-Axis Advanced Motion Controllers
PCI-8254/8258
Motion Controller
ADLINK's new PCI-8254 and PCI-8258 incorporate up-to-date floating-point DSP and FPGA technology to provide high-speed and high performance hybrid analog and pulse-train motion command. Leveraging ADLINK Softmotion technology, the PCI-8254/PCI-8258 offer more comprehensive and application-oriented motion functions to reduce the development time but maintain superior throughput and accuracy. Also delivered is excellent synchronous motion control performance.
-
Product
64-Axis PCIe EtherCAT MainDevice Motion Controller
PCIe-8338
Motion Controller
ADLINK PCIe-8338 is a hardware-based EtherCAT motion controller able to support up to 64 synchronized axes and over 10,000 points simultaneously. The PCIe-8338 features dedicated isolated emergency stop input (EMG), and configurable isolated high-speed digital input as not only generic sensor input but also pulsar input, with up to 1MHz input frequency. Optimum jitter control is provided in minimal cycles of 250µs to optimize synchronous I/O performance for vertical automation applications in semiconductor, electronic manufacturing, and others. The PCIe-8338 provides an out-of-shell application-ready (APS) function library to generate multi-dimensional, highly synchronized, time-deterministic event-triggered motion & I/O control. A wide range of compatible 3rd party SubDevice are easily designed with ADLINK's APS function library. ADLINK's MotionCreatorPro 2 utility is fully compliant with the Microsoft Windows environment, that allows complete EtherCAT motion and I/O configuration and function evaluation as well as compiling program download functions.
-
Product
PXI-5922, 24-Bit, 32MB/ch Flexible Resolution PXI Oscilloscope
779153-02
Oscilloscope
The PXI‑5922 high-resolution oscilloscope features a flexible measurement resolution range up to 24 bits, with up to 114 dBc spurious‑free dynamic range (SFDR), and up to 15 MS/s rates. This PXI oscilloscope has flexible settings for coupling and voltage range, as well as a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. The PXI‑5922 is capable of taking extremely resolute and accurate analog measurements. It is ideal for audio signals, spectrum analysis, and other small, accurate signal measurements. The PXI‑5922 also features PXI synchronization and data streaming capabilities.
-
Product
Data Acquisition (DAQ) Software - Dewesoft X
-
Data Acquisition (DAQ) SoftwareDewesoft has been developing leading data acquisition (DAQ) software for more than 20 years. Dewesoft X is the world's best data acquisition (DAQ), data recording, and data analysis software.The software received multiple international awards, is innovative, very easy to use, and requires no programming to acquire, store and analyze data synchronized from several data sources - analog, digital, CAN, CAN FD, CXP, GPS, video, serial and many other data interfaces.Our DAQ software is included for free to all of our data acquisition systems and we offer FREE support and FREE software upgrades forever. No hidden costs. Using our software is easier than riding a bike and has been trusted for years by the world's biggest brands like NASA, Space X, Airbus, Boeing, General Motors, Audi, Ferrari, VW, Tesla, Honda, Toyota, Caterpillar, John Deere to name just a few.
-
Product
V-FullWaver
-
The V-FullWaver systems were specifically developed for precise full waveform time domain Induced Polarisation, Resistivity and SP measurements. Each system is fully independent; incorporating its own power source, GPS module and digital memory for up to 3 months continuous recording. The V-FullWaver is a dual channel Induced Polarisation, Resistivity and SP receiver. Continually recording at 10ms sample rate provides a full waveform record. It can be synchronized on the GPS PPS signal, allowing an easy process of the signal. Data on the memory can be downloaded directly on a simple USB stick from all the Fullwavers.
-
Product
PTP Grandmaster
OSA 5335
-
Our OSA 5335 Modular PTP Grandmaster is a scale-able and high-performance IEEE 1588 v2 standard compliant Grandmaster Clock for the distribution of frequency, phase and time synchronization over packet-based network infrastructure including IP/MPLS, Carrier Ethernet, PON and DSL networks. Its carrier-class design provides high client capacity and a wide range of redundancy options to deliver scale-able performance and maximum availability. Our OSA 5335 is designed to deliver precise and reliable frequency, phase and time-of-day information in markets including telecommunications, media broadcast and power utility communications.
-
Product
PXI Switch - 4x8 2-Wire Matrix Module
PXI-7931
Matrix Switch Module
ADLINK PXI-7931 is a matrix module with 32 cross-point 2-wire relays (DPDT, 2 Form C). The default configuration of the PXI-7931 itself is a 4-group 2x4 2-wire matrix. With the termination board, TB-6231, users could flexibly choose one of the configurations: one 4x8, two 4x4, one 2x16, two 2x8 and four 2x4. Any contact of the PXI-7931 can connect to other contacts, individually or in combination. The PXI-7931 matrix module simplifies the wiring and makes it easy to change the internal connection path. The contact position of the relays can be changed either by direct software commands or by following the instructions previously stored in the on-board scan list. The scan list advances upon the trigger from external measurement devices, such as a DMM. The scan list could also advance when the scan-delay timer expires. In the PXI-7931, PXI trigger functions are supported and software programmable. Multiple modules can therefore be synchronized without additional field wiring.
-
Product
PXIe 16 Bit Arbitrary Waveform Generator - up to 1.25 GS/s on 1 Channel
M4X.6630-X4
Arbitrary Waveform Generator
The M4x.66xx-x4 series arbitrary waveform generators (AWG) deliver the highest performance in both speed and resolution. The series includes PXI Express (PXIe) cards with either one, two or four synchronous channels. The large onboard memory can be segmented to replay different waveform sequences. The AWG features a PCI Express x4 Gen 2 interface that offers outstanding data streaming performance. The interface and Spectrum’s optimized drivers enable data transfer rates in excess of 2.8 GB/s so that signals can continuously replayed at a high output rate. While the cards have been designed using the latest technology they are still software compatible with the drivers from earlier Spectrum waveform generators. So, existing customers can use the same software they developed for a 10 year old 20 MS/s AWG card and for an M4x series 625 MS/s AWG.
-
Product
IRIG Time Code Receiver & Generator Module
TCR180
-
Meinberg Funkuhren GmbH & Co. KG
The module TCR180 has been designed to receive and to generate IRIG-A/B/G, IEEE 1344, IEEE C37.118 or AFNOR NF S87-500 time codes. It is used in applications like data acquisition, standalone computer time synchronization (for systems without a network connection or higher accuracy requirements) or as an IRIG converter device. The frequency locking of the master oscillator to the time code system enables this module to generate fixed and programmable standard frequencies with high accuracy and stability. Various oscillator options allow the cost efficient implementation of different requirements concerning the accurracy of the outputs. The generator of the IMS-TCR module generates pulses per second and per minute and per hour. Four programmable outputs are also available. The pulses are synchronized to UTC-second.
-
Product
4-Channel 200 MHz A/D with Multiband DDCs, Kintex UltraScale FPGA - 3U VPX
Model 52862
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Complete radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- Four 200 MHz 16-bit A/Ds- Four wideband DDCs and- 32 multiband DDCs (digital downconverters)- 5 GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x4- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
