-
product
100MS/s 100MHz BW LPT/parallel Port 2-Channel Digital Storage Oscilloscope, Spectrum Analyzer, Voltmeter, Transient Recorder, AWG/Function Generator
HS801-AWG
The HS801: the first 100 MSPS measuring instrument that consists of an Arbitrary Waveform Generator/Function Generator, a Voltmeter, a Digital Storage Oscilloscope (DSO), a Spectrum analyzer, and a Transient Recorder. This new portable and compact measuring instrument can solve almost every measurement problem. Analyzing signals is done with 8-bit resolution and a maximum sampling speed of 100 MHz. The input range is 0.1 Volt full scale to 80 Volt full scale. The record length is 32K/64K samples.
-
product
Ball Pressure Test Apparatus
CX-Q03
Shenzhen Chuangxin Instruments Co., Ltd.
The Ball Pressure Apparatus is used to check the integrity of dielectric materials by exerting 20N force. The BPA10 is called out in IEC 60335, 60950, 61010, UL, CSA and European Norms. It is used to check the integrity of dielectric materials by exerting 20N force. The Ball Pressure Apparatus is made of stainless steel for long life. Since accelerated life procedures are used for this oven test, more than one apparatus may be useful for parallel testing.
-
product
SAFETY TESTERS ( CURRENT LEAKAGE TESTERS )
ST-05
Safety Tester Model ST-05 is a test set for testing small equipment powered by 120V 60 Hz, from an approved U-ground source. Test also can be run on double-insulated tools an on appliances with two-pin parallel plugs.
-
product
Digital Acquisition Card
PI-41000
The PI-41000-4G is a CompactPCI® bus based instrument card that allows the user to capture up to 32-bits of digital data into an on-board memory at clock rates up to 120 MHz. The inputs are software configurable to provide one 32-bit wide channel, one 16-bit wide channel with double depth or two 16-bit channels. When configured with a single 16-bit input, the card will capture at up to 120 MHz. When configured with two 16-bit inputs or as a single 32-bit input, the card will capture at up to 80 MHz. Each digital data channel requires three timing signals, frame, line and pixel to accommodate the data capture. When operating in a two channel mode, clocks from channel A can be used to provide timing to channel B. For wider words or multiple channels, more boards can be used in parallel.
-
product
Digital Attenuators
Macom Technology Solutions Holdings Inc.
Digital Step Attenuators (DSA)are offered in up to 6 Bit control with lowest step size of 0.5 dB covering DC to 40 GHz. MACOM's DSAs can be controlled with serial and parallel control allowing for best implementation for our customers. These products exhibit low insertion loss and high attenuation accuracy and are offered both GaAs and Silicon (SOI) processes and are offered in both packaged and bare die form factors.
-
product
4-Port In-System Programmer For Silicon Labs
MPQ-C2
Supports Silcon Labs C8051F series devices with C2 Programming Interface Field Upgradeable - always supporting the latest devices Secure image management - protects your IP In-circuit gang programming of up to four devices at once Can be deployed in arrays to program up to 64 devices in parallel Stand-alone, PC-controlled or ATE-controlled operation Automatic device serialization
-
product
4000W to 50,000W - Single Output
ALE-Rack Mount Series
*Compact, lightweight design*Simple parallel operation for higher power*Worldwide input voltages/frequencies*Fully adjustable output voltage*Full remote control interface*Safety agency approvals
-
product
Safety Compliance Test System
EN 60601
Test system for electrical safety compliance testing of medical products in accordance with EN 60601-1, 3rd edition.The system is equipped with three test fixtures which are connected in parallel order to reduce the number of setup tasks for different variants in the course of day-to-day manufacturing processes. Its purpose is to test medical products, e. g. patient monitors, which are employed at hospitals to monitor heartbeat and oxygen saturation.Based on the integrated electrical safety tester by Associated Research, in combination with an AC power source and a switching matrix, it is possible to fully automate tests like for instance AC/DC high-voltage tests, insulation resistance measurements, earth connection tests and leakage current measurements.The required occupational safety is provided by a high-voltage safety hood in accordance with EN 501191. The entire safety technology, as well as the control PC, is mounted in an aluminum-profile cart.
-
product
Exchangeable Test Fixture
2112/D/H/S-7/HG/Pylon
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 13,50 kg
-
product
50MHz BW, 50MS/s, 2-Channel PC-based Digital Storage Oscilloscope (DSO)
PCS500AU
The PCS500AU is a digital storage oscilloscope that uses a computer and its monitor to display waveforms. All standard oscilloscope functions are available through the supplied Windows program. Its operation is identical to that of normal oscilloscope apart from the fact that all operations can be performed with the mouse. Connection is through the computer's parallel port and the scope is completely optically isolated from the computer port. The oscilloscope and transient recorder have two completely separated channels with a sampling frequency up to 1GHz. Any waveform displayed on the screen can be stored for later use in documents or for the comparison of waveforms.
-
product
Analog or Digital Communications Switching Systems with D Type Connectors
RS Series
The RS Series computer controlled switching systems are designed to switch multi-wire groups of signal up to 25 wires. These systems are typically used for signals such as parallel TTL, RS232, RS422, WAN or modems, but can also be used for any group of analog or digital signals having a bandpass up to 30 MHz or a data rate up to 20 Mbps.
-
product
MEMS And Sensor Test Solutions
Modular design based on standard handlers, high parallelism, ambient to automotive tri-temp handling.
-
product
Multiplexers (MUX)
WDM
It is highly desirable to reduce the number of cables required to communicate between spaces on Navy ships due to increased weight, cost and maintenance concerns. To reduce weight and expense, copper-based NTDS parallel and serial type cables can be converted to fiber optic and multiplexed using Wavelength Division Multiplexing (WDM) technology. WDM technology allows for multiple fiber optic wavelengths to be combined in a single fiber and then separated back to individual fibers at the distant end. Using Coarse WDM (CWDM) which utilizes wavelengths 20nm apart ranging from 1271 nm to 1611 nm, provides for up to 18 optical wavelengths to be combined into a single fiber. Optionally Dense WDM (DWDM) can be used allowing for up to 160 optical wavelengths.
-
product
High Power Programmable AC Source with Transients
61510
Chroma Systems Solutions, Inc.
Power Rating:61511: 12KVA61512: 18KVAVoltage Range: 0-150V/0-300V / AutoConfigurations with input voltage of 220V or 480VFrequency: DC, 15Hz-1500HzSingle-phase or three-phase output selectableProgrammable slew rate setting for changing voltage and frequencyProgrammable voltage and current limitHigh output current crest factor, ideal for inrush current testingTurn on, turn off phase angle controlTTL signal which indicates output transientLIST, PULSE, STEP mode functions for testing Power Line Disturbance (PLD) simulationVoltage dips, short interruption and voltage variation simulationHarmonics, inter-harmonics waveform synthesizerComprehensive measurement capability, including current harmonicsAnalog programmable interfacesRemote interface: GPIB, RS-232, USB and EthernetCapable of delivering power output up to 90KVA by implementing Master-slave parallel operation
-
product
Battery Capacity Testers|Discharge Testers
DV Power offers a wide range of battery capacity testers to meet specific customer needs. All of them are portable, powerful and most of all universal. Any battery string, such as lead-acid, lithium-ion, nickel-cadmium based and others, with voltages in the range of 0,9 – 800 V DC can be tested in an accurate, user-friendly way.The capacity test is carried out following the battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22, and other relevant standards.BLU battery testers enable setting the discharge current up to 350 A, with 0,1 A resolution. If higher currents are required, several units can be connected in parallel, or BXL additional load units can be used. Discharge parameters can be monitored in real-time during the capacity test. Overall battery voltage, current, elapsed test time and capacity will be presented during the entire test on a touch screen display.
-
product
Solution For Test-in-Strip
InCarrier
The InCarrier process is based on a strip-like device carrier for single devices that combines the advantages of the singulated device test with the advantages of high parallel strip test. Leveraging the strip like design the InCarrier ensures robust test-handling for even smallest devices and supports high parallel test.
-
product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196A
The 16196A surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results - reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement - now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
product
Multi-Channel Synchronization Module for M8190A, M8020A or M8030A
M8192A
Complex testing sometimes requires playing multiple waveforms in parallel (e.g. multi-emitter testing). The M8192A synchronization module allows engineers to synchronize up to 12 M8190A channels and fits into a standard AXIe frame.The M8192A synchronization module also supports testing of high-speed digital busses like PCI Express.Test efficiency can be increased by testing up to 10 lanes with the M8051A and the M8041A BERT modules in parallel. These can be synchronized by the M8192A module.
-
product
Mission Critical, Fault Tolerant Power Supplies
Series HSF
- Hot-swappable plug-in power supplies.- Designed to be combined in an N+1 fault-tolerant power system.- Front panel voltage adjustment trimmer for adjustment of output voltage.- Built-in forced current sharing and or-ing diodes.- May also be used independently as a multi-output power supply.- Designed to be sustainable - new models are backward compatible with existing racks.- Available in 1U and 3U sizes. Mounts in 19-, 23-, and 24-inch equipment racks.- All models include power factor correction (PFC).- Full service customized DC power distribution systems can match power supply output(s) with your load(s).- I/O connections via 24 pin connector that plugs into rack adapter. External connections are made via rack adapter.- Surface mount technology permits minimum mounting space.- Entire RA 19 racks populated with HSF power supplies can be connected in parallel, parallel-redundant or series.- HSF are CE Marked per per the LVD, EMC and RoHS 2 Directives. See applicable Declaration of Conformity.- Compliant with UL 8750, Standard for LED Equipment,- Watch video of NEBS GR-63-CORE earthquake and office vibration testing.
-
product
AMR Angle Sensors
MultiDimension Technology Co.,Ltd.
Iis proportional to the sine or cosine functions of two times of the angle – sin(2α) and cos(2α) – of a magnetic field applied parallel to the surface of the sensor, which can be provided by a small magnet positioned above the device.
-
product
High Performance DC/DC Converters
The 4:1 Input Voltage 1000 Watt Single FXP DC/DC Full Brick converter is designed to operate in parallel with up to 3 FXP bricks (2800 Watts) with no external circuitry. The FXP series provides a precisely regulated DC output. The output voltage is fully isolated from the input, allowing the output to be positive or negative polarity and with various ground connections.
-
product
LCR & Component Tester
PeakTech Prüf- und Messtechnik GmbH
Digital LCR measuring device for resistance, capacitance and inductance with high-resolution dual multifunction display. Components can be measured in series or in parallel and the LCR meter also offers the choice between automatic and manual range selection.
-
product
Three Axis Interferometer
10736A
The Keysight 10736A Three Axis Interferometer is used in multiple axis applications where linear and angular control of the stage is required. It combines in a single package the functionality of an optical bench with multiple beam benders, beam splitters, and three interferometers. The interferometers split an incoming laser beam into three beams to measure linear distance, pitch and yaw, or linear distance, roll and yaw. Three linear measurements provide the basis for calculating two angular measurements. The inherent beam parallelism ensures that there is essentially no cosine error between the three measurements and also ensures angle accuracy for pitch and yaw measurements. Other characteristics include:
-
product
4-Port In-System Programmer for Cypress
MPQ-PSoC
Supports Cypress PSoC/3/5 and enCoRe II/III/V device families Field Upgradeable - always supporting the latest devices Secure image management - protects your IP In-circuit gang programming of up to four devices at once Can be deployed in arrays to program up to 64 devices in parallel Stand-alone, PC-controlled or ATE-controlled operation Automatic device serialization
-
product
Power Supply 303d-II
PowerLab triple Series power supplies are reliable and accurate laboratory equipment with two outputs with adjustable and stabilized DC voltage and regulated ( limited ) power consumption and additional output has – voltage . Adjustable outputs can work independently , in series (max output voltage 120V DC for model 605- II) or parallel (max current of 10A for models 305- II and 605- II) . Power can be used in the design of electronic products , scientific works , laboratories, production lines and in teaching .
-
product
Resister Blackjack
Resistor blackjack is like regular blackjack but better! Your goal is to assemble a single resistance from several resistors that is as close to 21k while not being over.Unlike regular blackjack, the resistors can be combined in series and in parallel, giving the game a whole new dimension. Plus, resistors have tolerances so achieving a mathematical 21k doesn't guarantee a win.
-
product
8-Sites Flash Programmer w/Relay Barrier, True Parallel Channels
YAV90FR2
The YAV90FR2 or YAM90FR2 is a flash programmer housed in a compact 6TL YAV Module form factor, designed forseamless integration into automated test environments. It incorporates the advanced FlashRunner 2.0 technology fromSMH, enabling efficient programming of microcontrollers, flash memory, and other logic or memory devices. Themodule features flexible connectivity options, with all digital I/O (DIO), programmable voltage lines, and correspondingground lines switchable via integrated relays.
-
product
VITA 57.4 FMC+ HSPC Loopback Card
Samtec's VITA 57.4 FMC+ HSPC Loopback Card provides FPGA designers an easy to use loopback option for testing low-speed and high-speed multi-gigabit transceivers on any FPGA development board or FPGA carrier card. It can run system data or BER testing on all channels in parallel. This makes evaluation and development with an FPGA much easier and is an ideal substitute for 28 Gbps test equipment.
-
product
Miniature 8-channel photon counter
id150 SERIES
Intended for large-volume OEM applications, the id150-1x8 is the only multichannel solid-state single photon detector on the market. It consists of a CMOS silicon chip packaged in a standard TO8-16pin header with a transparent window cap. The chip combines 8 in-line single photon avalanche diodes that can be accessed simultaneously for parallel processing. square in center-to-center A fast active quenching circuit is integrated within each pixel in order to operate each diode in photon counting regime. The chip is mounted on a printed circuit board on top of a single-stage thermoelectric cooler (TEC). A thermistor can be used to measure the temperature of the chip. Only two low power supplies of +5V and -25V are needed for operation in photon counting mode. The fast active quenching circuit leads to a dead time of less than 50ns per channel. An outstanding timing resolution of less than 60ps allows high accuracy measurements.
-
product
Analog Meter
PR-A Series
The PR-A Series of series-regulated CV/CC power supplied were designed to provide a compact power supply package with high performance, and ensure excellent reliability as well as excellent design. Four types are available, three 18V types and one 36V type. Whether used individually or connected in series or parallel for greater capacity, the PR-A Series are housed in a compact rack-mount package and can be used on the bench top as well.
