-
Product
Fully Automatic Full Load (Routine) Testing Panel For Induction Motor
-
Aarohi Embedded Systems Pvt. Ltd
Aarohi introduced fully automatic routine testing panel. The primary purpose of the routine test is to insure freedom from electrical and mechanical defects, and to demonstrate by means of key tests the similarity of the motor to a “standard” motor of the same design. this panel also help to enhance productivity, Work efficiency & reduces need for skill operator. More then 500 Indian pump manufacturer ware installed this system & satisfied with performance.
-
Product
Cell Fractionation Filter
CELLNETTA MZM1 Series
-
Cell sorters, magnetic beads, and gravity separation are common cell fractionation methods. CELLNETTA uses the micron size differences of cells to enable conventionally difficult high-precision fractionation and simple cell separation using an innovative fractionation filter.
-
Product
FC(Fuel Cell) Impedance Measurement System
KFM2150 System
-
The KFM2150 system is a fuel cell impedance measurement system configured with an FC impedance meter KFM2150 and an electronic load PLZ-4W series. Combination of KFM2150 and PLZ-4WA series (0V input type) supports impedance measurement for single cell of fuel cell.In addition to impedance measurement with AC impedance method, KFM2150 system provides IR measurement with current interrupt method.Application software enables test for each characteristic of fuel cell such as I-V characteristics, Constant Current characteristics, Current Interrupt method and Cole-Cole plot by the AC impedance method. Moreover, each test can be performed in a specified order.
-
Product
DC Electronic Loads
-
Next Generation Instrumental (Shanghai) T&C Tech. Co., Ltd.
NGI DC Electronic Loads
-
Product
SparkFun Load Sensor Combinator
-
The SparkFun Load Sensor Combinator is a bare PCB that combines four load sensors into a standard four-wire Wheatstone bridge configuration. If you open up an electronic bathroom scale, you’ll find a large rat's nest of wires. The Load Sensor Combinator was created to combine the 12 wires found in a bathroom scale into the standard four-wire Wheatstone bridge configuration.
-
Product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-1500B Open loop method
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
Product
Load Switches
-
Analog Devices load switches provide a highly integrated solution for switching voltage rails on in a controlled manner via an internal, high-side switch. This portfolio features overcurrent and overtemperature protection and supports currents up to 3 A. They provide a very low pass element RDSON to reduce power losses. The combination of the functionality and integration levels of ADI load switches make them extremely well-suited to inrush control applications for pluggable optical modules, line side pluggable interfaces protection, power plane switching, and power rail sequencing applications.
-
Product
1800~3000W DC Electronic Loads
JT633 series
-
Nanjing Jartul Electronic Co., Ltd
JT633 series electronic load is functioned with 500KHz high-speed synchronous sampling, DSP technology, powerful dynamic test and multi-aspect intelligence analysis. All these are fully integrated into auotmatic test function, which makes JT633 series load very suitable for testing power supply when produced in large quantity. Besides, JT633 series load also possesses the features of current rising slew rate programmable, high-speed dynamic loading and programmable list function, which makes JT633 series load satisfing most of R&D requirements.
-
Product
Water Filler for Nickel-Cadmium Cells
MasterFiller
-
The MasterFiller is an instrument designed to deliver measured quantities of distilled water as required in the service of Aircraft Nickel-Cadmium batteries.· The MasterFiller consists of a microprocessor controlled pump with a level sensing probe, a keypad and display and an external 12VDC power supply (or optional battery).· The MasterFiller is part of a system comprising Intelligent Charger-Analyzers and Software for Battery Data Acquisition and Analysis, designed to improve the accuracy and efficiency of the process of testing batteries for airworthiness certification.
-
Product
Clamp type AC Current Sensor／for Load Current Measurements(CT Series)
CT-33
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Compact size*AC 1A～200A*Current measurements of feeder
-
Product
4kW Electronic Load
PT04-48
-
For Telecom Rectifier and Power Supply testing. This model has been developed to accommodate testing of both 48V and 24V telecommunications power systems or Power Supplies. It is also useful as a general-purpose variable Load. Its founding principle is simplicity – ease of use, enhanced reliability, greater value for money and wider applicability.
-
Product
3 Way GPS / GNSS Signal Splitter Passive, 1-2 GHz, N Type, DC Block+200Ω Load 3 Ports
GPS302
-
INSTOCK Wireless Components, Inc
GPS L1 - L5, GLONASS, Galileo splitterLow Insertion Loss (0.3 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)15 VDC & 75 mA max on DC block portsTri Alloy N Type Female (Jack) 50 Ohm
-
Product
Battery Load Tester
BT-100
-
Schumacher Electric Corporation
FOR EVERYDAY DIY USEEasy to operateTest load, battery condition, starter motor draw and complete charging system diagnosis.Works on 6 and 12 volt batteries50 amp load test for 6 volt batteries100 amp load test for 12 volt batteries Tests 6 and 12 volt batteries ─ up to 1000 CCATop-mounted rocker switch for easier operationSuper-grip, heavy-duty color-coded battery clampsEasy-to-read meter ─ accurate and shock resistantBaked enamel, steel case ─ ventilated to keep coolRubber insulated carrying handle ─ for comfort and safety
-
Product
Diffusion Cell Testing
-
Teledyne LABS Phoenix™ Dry‐Heat Systems make diffusion‐cell testing faster, easier, and more economical. The Phoenix Systemincludes an advanced diffusion cell design. Options include the compact Phoenix DB-6 six‐cell manual sampling system and the Phoenix RDS automated sampling system capable of handling up to 24 diffusion cells at once.An important advantage of the Phoenix System is the speed with which receptor cell contents are homogenized. Visual testing with red dye placed on the surface of the media at the top of the sampling arm shows complete dispersion occurs within a few seconds.Explore the pages in this section to learn more and to configure your own system.
-
Product
Micro Power or Micro Coax, Insert, Receiver, SIM, 2 Pos, 2 Slot (not loaded)
510180104
SIM Insert
Not loaded. Micro Power or Micro Coax patchcords need to be purchased separately.
-
Product
High Power DC Electronic Load
34000A Series（5KW~40KW）
-
34000A Series has its own control and display panel, CC / CR / CV / CP / Dynamic modes, 150 sets Store / Recall memory which provides load set-up more efficiently, also can be remote controlled via GPIB、RS232、USB and LAN interface.SHORT time setting and SHORT_VH, SHORT_VL setting function, also can measure Short Voltage and Current.
-
Product
Self Powered Active Load
TBOH02
-
The TBOH02 is a self powered, precision active load. It does not need a separate supply voltage and operates as low as 2V. Its features include constant resistance and constant current mode. A 10 turn potentiometer with dial, a range switch and a precision reference enable accurate setting of current or resistance. Furthermore it can be controlled by an external voltage.
-
Product
APU Test Cells
-
Atec is a leader in test cell design and construction for aircraft auxiliary power units (APUs). We are licensed and experienced for work with all major OEMs, DoD, and US Allies. Our Phoenix™ APU Cells feature common configuration, modular utilities, and fast installation and startup.
-
Product
AC Load Banks
-
Power House Manufacturing, Inc.
Hand carried AC load banks in any capacity to meet your load testing needs. Power House Manufacturing has developed the best ultra-compact and light-weight hand carried AC load banks. AC load banks with capacities unmatched in the industry.
-
Product
Battery Cell Tester
-
This Centre zero instruments help to read the voltage irrespective of polarity.
-
Product
Solar Cell Systems
-
he Solar Cell Scan is a multifunctionalexperimental platform,which is based on the measurement of Quantum Efficiency (QE) . The system employs a turnkey integrated design, which can carry out QE, Reflectivity and Mapping testing functions automatically. There are also modular and customdesigned accessories to adapt to different solar cell samples.
-
Product
Signal, Insert, Receiver, QuadraPaddle, SIM, 1 Slot (not loaded- for discrete wiring only)
510180101
SIM Insert
Signal, Insert, Receiver, QuadraPaddle, SIM, 1 Slot (not loaded- for discrete wiring only).
-
Product
48V / 250 Amp Load
EL15-48M
-
For Telecom Rectifier and Power Supply testing. This particular Load has been designed to operate with Telecom 48V Rectifiers and Power Supplies with output Voltages in the range of 38V to 60V and is extremely cost effective.
-
Product
Signal, Module, Receiver, QuadraPaddle, 90 Series, 192 Position, Fully Loaded w/ Twin Female Contacts
510150130
Receiver Module
Primary mating module 510151105. (May mate with other ITA modules, as well.)
-
Product
Resistivity Cell For N1413 (26/50 Mm Electrodes)
N1424B
-
The N1424B is designed to operate specifically with the B2985B/87B Electrometer/High Resistance Meter. It is used to measure surface or volume resistance/resistivity of insulation materials. The N1413A High Resistance Meter Fixture Adapter is required to connect the N1424B to the B2985B/87B.
-
Product
Testing for Si Solar Cells Using High Performance CCD
EL Imaging Tester
-
EL Testing for Si Solar Cells using High Performance CCD. The determination of luminescence (photo emissions) in solar cells is an important characterization tool. Typical solar cells often have defects which limit the efficiency or lifetime of a cell. Many of these defects are visualized with Luminescence Imaging. By using this technique, the manufacturing process can be optimized to produce better cells. Luminescence Imaging takes advantage of the radiative inter-band recombination of excited charge carriers in solar cells. The emitted photons can be captured with a sensitive CCD camera to obtain an image of the distribution of the radiative recombination in the cell. This distribution is determined by the local excitation level, allowing the detection of electrical losses, thus mapping the diffusion length of minority carriers as the emitted light is low intensity and in the near infra-red range, the CCD camera has a high sensitivity wavelength from 900 to 1100 nm with little thermal noise. This CCD camera provides excellent resolution of 1024 x 1024 pixels with a large 1μm pixel size, multi-megahertz readout speed, and robust USB 2.0 connectivity. The EL CCD Camera is the ultimate high-performance CCD camera for electroluminescence and photoluminescence imaging for Photovoltaic (PV) Cells and Modules. This camera combines low noise electronics and optimal sensitivity in NIR.
-
Product
Signal Module, ITA, QuadraPaddle, 90 Series, 192 Position, Fully Loaded with Round Posts (610 138 115)
510151107
ITA Module
Used together with QP ITA module p/n 510109316 for PCB mounting. NOTE: Mounting screws for this module are included with module part # 510109316. Primary mating module 510150115. (May mate with other Receiver modules, as well.)
-
Product
Characterization of Solar Cells
Paios
-
Paios performs a large variety of experiments in no time with one click. Get consistent and precise measurement data, directly compare your results in the measurement software and speed up your research.Increase your research speedCompare your devices directly in the softwareGet highly consistent dataThink about physics - Let Paios handle the rest
-
Product
High Voltage DC Electronic Load
3360F Series（600W~14.4KW）
-
3360F has its own control and display panel, CC/CR/CV/CP/Dynamic modes, 150 sets Store/Recall memory which provides load set-up more efficiently, also can be remote controlled via GPIB, RS232,USB and LAN interface.
-
Product
PXI Mixed Configuration Relay Module - 9 Cells Populated
40-138-AA-BB-CC-DD (9 CELL)
Relay
The 40-138 2A Relay Module with 9 cells populated is a cell-based mixed configuration switching module suitable for applications requiring medium power switching with high density. It provides a broad selection of mixed relay types for greater flexibility and features 2A current capacity and voltages to 300VDC/250VAC.
