Optic Amplifiers
Devices that boost light signal in an optical fiber network. The optical signal is amplified directly without need for electrical conversion.
-
Product
Variable Optical Attenuators
-
A fiber optic variable attenuator is used to reduce the power level of an optical signal in fiber optic communications.
-
Product
47~862MHz FTTH Digital TV Low Optical Receiver
H9122L
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai H9122L, operating bandwidth of 47 ~ 862MHz, is a suitable digital television FTTH applications, ultra-low optical receiver, Whether used in analog television or digital television. Receiving at high optical power can be adjusted by PAD level, played limiting output, so H9122L within a large dynamic range of the received optical power of +2 dBm ~-20dBm, have excellent characteristics.
-
Product
Operational Amplifier
Op Amp Series
-
The amplifier is capable of operating at supply voltages from 0.9V to 3V with specified specs at 1V and 1.8V single supply.The input common mode range extends to both power supply rails without the offset glitch and input bias current phase reversal inherent to most rail to rail input amplifiers.
-
Product
Precision Fiber Optic Cleaver With Scrap Collector
HW-05C
-
Shanghai Fibretool Technology Co.,Ltd.
The HW-05C Fiber Optic Cleaver gives you high precision at low cost. This compact and easy to use cleaver is perfect for all cleaving applications, from fusion splicing to mechanical splicing and field installing quick termination connectors. The HW-05C works with both 250um coated and 900um buffered fibers.
-
Product
Low Noise Amplifiers
-
Electronic component that amplifies a very low-power signal without significantly degrading its signal-to-noise ratio (SNR).
-
Product
Fiber Optic Talk Set
-
Fiber optic talk set consists of both the fiber optic light source and transceivers, which carry voice over the spare fiber in both directions. When doing the test work, technicians may need remote location communication during the measurement or splicing work, and sometimes radio-based communications may not be suitable because of environmental conditions such as FCC restrictions, etc. fiber optic talk set will function well in such cases, they could utilize the already installed fiber optic link to carry voice communications.
-
Product
47~862MHz FTTH CATV AGC Optical Receiver
H9112G
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai H9112G, the operating bandwidth of 47~862MHz, Products with high sensitivity optical receiver tube and Huatai special low noise matching circuit,Whether used in analog television or digital television, have high reception sensitivity and excellent intermodulation distortion index. is a low power, high performance, cost-effective triple play, FTTH CATV AGC optical receiver.
-
Product
FTTH Optical Node
SR201W
-
Hangzhou Softel Optic Co., Ltd.
SR201W is a mini in-door optical receiver with WDM that especially design for FTTP/FTTH application. High performance, low receiver optical power and lower cost is FTTH solution best selection for MSO. WDM integrated for 1550nm video signal and 1490nm /1310nm data signal in one fiber. Reflection 1490nm/1310nm for connecting ONT device. They are very suitable for PON and TV system
-
Product
Analog Optical Power Meter - MATRIQ
1500 Series
-
The Power 1500 Series analog power meter brings cost-effective test and measurement. The Power 1500 provides logarithmic analog output as well as a digital optical power meter for applications that require real-time feedback.
-
Product
Economical Type Forward Path AGC Optical Receiver
HR8136, HR8153
-
Hangzhou Huatai Optic Tech. Co., Ltd.
HR8100 series is an economical type forward path AGC optical receiver. Its technical performance and index are the same as HR9100, except without 20-segment output level indication and network management interface.
-
Product
Optical Spectrum Analyzers
-
Thorlabs' Optical Spectrum Analyzers (OSAs) perform highly accurate spectral measurements. Compatible with fiber-coupled and free-space light sources, these compact benchtop instruments suit a wide variety of applications, such as analyzing the spectrum of a telecom signal, resolving the Fabry-Perot modes of a gain chip, and identifying gas absorption lines.
-
Product
Low Noise Amplifier
-
Low noise amplifier with a typical small signal gain of 22 dB and a nominal noise figure of 5dB across the frequencyrange of 90 to 110 GHz.
-
Product
Optical Fiber 1×2 Switch
OFSW - 1 × 2
-
Hangzhou Huatai Optic Tech. Co., Ltd.
OFSW- 1×2 is a 1×2 prism optical switch. It can support 1 optical fibers input and 2 fiber output, channel switch. Wide operating wavelength range, low insertion loss and speedy switching rate, can use network trends configuration, network monitor and lab application.
-
Product
Fiber Optic Measurement Systems & Sensors
-
MTI Instruments offers large measurement range and standoff distance fiber-optic measurement sensors and probes that provide ultra sensitive linear output response. Our modular (interchangeable) non-contact fiber optic sensors systems have dual channel that enables the user to make simultaneous measurements. Our fiber optic probes are designed to automatically compensate large changes in reflectivity making it possible to monitor dynamic reflectance of up to 100:1 making it ideal for measuring vibration of ultrasonic horns, modal analysis of disk drive suspension, displacement and timing of fuel injectors and lateral motion measurements.
-
Product
Fiber Optic Sensors And Amplifiers
-
Omron’s high-performance fiber optic sensors and amplifiers come in a wide variety of configurations to meet your specialized requirements.
-
Product
Optical Inspection Machine
3D AOI
-
3D AOI latest optical inspection machine 1. No part dead angle, 4-way projection, complete measurement 2. Part height measurement, accurate measurement of defects 3. Multi-piece inspection without additional program 4. DLP digital projection, program editable height measurement
-
Product
High Speed High Voltage Amplifier
WMA-320
-
The WMA-320 is a high voltage, wide bandwidth laboratory amplifier. Its high output voltage, current and wide bandwidth have been designed to serve the needs of a wide variety of high-tech experiments. The WMA-320 can be used for MEMS actuation, EO-modulators, PZT (piezo) positioners, ultrasonics, and many other applications.
-
Product
Optical Fiber Identifier
-
Anfkom International Co.,Limited
It is an essential installation and maintenance instrument.By inserting the fiber into its adapter head,it can identify SM optical fibers without any damage by detecting the optical signals being transmitted through them so as to avoid the opening of the fiber at the splice point for identification and thus avoids the interruption of the service.In the presence of traffic, the intermittently audible tone is activated.The 3306A optical fiber identifier also allows relative core power display and identification of the 270Hz,1kHz and 2kHz frequencies. When they are used to detect the frequency, the continuously audible tone is activated.There are four types of adapter heads available: 0.25,0.9,3.0 and 2.0.The 3306A optical fiber identifier is powered by a 9V alkaline battery.
-
Product
Near-Field Scanning Optical Microscope Platform
MoScan-F
-
MoScan-F is a device that enables you to get the best up-to-date available spatial optical resolution using the near field scanning optical microscope (NSOM) principle
-
Product
Limiting Amplifiers
-
Teledyne Microwave Solutions (TMS) offer a range of Limiting Amplifiers which are used in instantaneous frequency and phase measurement receivers. The most important performance requirement of a limiting amplifier is to minimize output power variations, and provide a constant output over a wide input dynamic range.
-
-
Product
Precision Optics and Assemblies
-
For more than 35 years, Keysight has been designing and fabricating leading-edge optics for use in our laser interferometer systems. You can take advantage of this engineering, component fabrication, and assembly expertise and our state-of-the-art optics manufacturing facility in Santa Clara, California to deliver cutting-edge optical solutions to your customers:
-
Product
Non-contact Optical Installation for Control of the Shape of Castings
-
To develop an installation for the control of the shape of plastic castings in production. The installation must control the shape of the part by comparison with the sample. The installation should be designed for use by technical personnel and provide the ability to automatically select a sample for comparison from a small set.
-
Product
47~862MHz FTTH CATV Optical Receiver
H9122
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai H9122, the operating bandwidth of 47~862MHz, Products with high sensitivity optical receiver tube and Huatai special low noise matching circuit,Whether used in analog television or digital television, have high reception sensitivity and excellent intermodulation distortion index. is a low power, high performance, cost-effective triple play, FTTH CATV optical receiver.
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Multi-Mode, 50/125 Fiber
40-852A-318-M50-HI
-
The 40/42-852A-318-M50 is a PXI/PXIe 8-channel multiplexer with MU (mini SC) connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
Shortwave Power Amplifier
OM4001HF
-
The OM Power model OM4001HF is designed for all short wave amateur bands from 1.8 to 29.7 MHz (including WARC bands) and all modes. It is equipped with a two ceramic tetrodes FU-728F.
-
Product
Erbium Doped Amplifier
CATV
-
Amonics CATY Rackmount EDFA area made with high power pump laser and stability pump combiners, robust in high power boosting. The result are EDFAs that possess high output power, high gain with very low noise, and are ideal for CATV applications. The turnkey microprocessor controlled rackmount EDFAs manage alarms and status indicators. An integrated RS232 or Ethernet computer interface enables easy control, diagnostic functions and data acquisition.
-
Product
Optical Light Sources
-
Wuhan Sunma Technology Co., Ltd.
Fiber Optic Light Sources are a necessity for performing fiber optic network testing to measure the fiber optical loss for both single mode fiber cable and multimode fiber cables. They are designed to cover a variety of wavelength ranges to suit all optical testing needs and usually the optical light sources are used with the fiber optic power meter to test the fiber system loss. Light sources are offered in a variety of types including LED, halogen and laser. Usually the optical light source is used with the fiber optic power meters, they act as an economic and efficient solution for the fiber optic network works. SunmaFiber offers handheld fiber optical light source and laser light source.
-
Product
Optics Test Systems
Mirror Collimator And Autocollimator
-
Optik Elektronik Gerätetechnik GmbH
Mirror collimator and autocollimator for the entire wavelength range from UV to MIR The compact mirror collimator can be used both as an autocollimator and as a telescope.
-
Product
Omicron Fiber Optic Connector
-
Teledyne Impulse-PDM’s Omicron 5030/5070 optical connectors utilize proven small form factor ferrule technology and are available for multi-mode or single-mode operation.The connectors are offered, as standard, in stainless steel to BSEN10088-3 Grade 1.4404 (316L), which is electro-polished to remove surface contamination, thus improving resistance to corrosion. Connector bodies can also be manufactured in other materials, either to address specific anti-corrosion requirements, or to increase depth rating. Engaging nuts are normally manufactured in naval brass to UNS C46400.
