Digital I/O
Input/output of digital values.
-
Product
Digital I/O Board, 32 Isolated I/O Channels, 24V
APCIE-1500
-
The PCI-Express 32 digital I/O board APCIe-1500 has 32 digital inputs/outputs (24 V or 12 V), 14 inputs are interruptible. The 16 digital power outputs are equipped with protection diodes and filters. The board is fully compatible to the PCI board APCI-1500. It is especially suited for applications like industrial I/O control, signal switching, ON/OFF monitoring of motors, lights etc. in the harsh industrial environment. The APCIe-1500 has interruptible inputs. They supersede continuous cyclical query processes (polling) for routine monitoring and evaluation tasks. This takes load off the processor and the software. At a change of state of the digital inputs the APCIe-1500 generates an interrupt, so that the system reacts on the event through the interrupt routine and herewith fulfils real-time criteria.
-
Product
48-Ch Digital I/O PC/104 Module
PCM-3724
-
48 TTL digital I/O linesOutput status read-backChannels simulate 8255 PPI mode 0Interrupt triggering, rising/falling edge
-
Product
PMC w/ 16x/8x ADC, 8x/4x DAC & 14x Digital I/O
TPMC532
-
The TPMC532 provides 16 or 8 channels of simultaneous sampling true differential bipolar 16-bit analog input, 8 or 4 channels of simultaneous update single-ended unipolar/bipolar 16-bit analog output and 14 channels of tri-state 5V-tolerant TTL digital input/output.
-
Product
PCI-6528, 48-Channel, 24 Sink/Source Inputs, 24 Sink/Source Outputs, Channel-Channel Isolated, Digital I/O Device
778833-01
Digital I/O Module
The PCI-6528 is an industrial, parallel digital I/O interface.With programmable power-up states, you can configure the initial output states in software, to ensure safe … operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6528 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
PCI Digital I/O and Relay Driver Cards
-
a 32-channel Digital I/O card with high output voltage and current capability and a dual variable threshold input. Each of the 32 channel outputs can be used to drive the output high or low using a high current capacity drive capable of sourcing 0.4A from the high side or 0.5A sink on the low side for each channel.
-
Product
16-Bit, 8-Ch Analog Output PCI Card With 16-Ch Digital I/O
PCI-1723
-
Auto calibration functionA 16-bit DAC is equipped for each analog output channelSynchronized output functionOutput values retained after system hot reset2-port (16-channel) user-defined digital input/outputBoardID™ switch
-
Product
48 Optocoupled Open Drain 42V 6A Digital Outputs
YAV90048
Digital I/O Module
6×8 Isolated Ouput Banks Trigger IN and OUT Termic and Overcurrent protection CAN Control (or Ethernet with Ethernet to CAN Gateway.) Drivers dll & VIs available.
-
Product
PXIe-6355, 80 AI (16-Bit, 1.25 MS/s), 2 AO, 24 DIO, PXI Multifunction I/O Module
783632-01
Multifunction I/O
PXIe, 80 AI (16-Bit, 1.25 MS/s), 2 AO, 24 DIO, PXI Multifunction I/O Module—The PXIe‑6355 offers analog I/O, digital I/O, and four 32‑bit counter/timers for PWM, encoder, frequency, event counting, and more. The device delivers high-performance functionality leveraging the high-throughput PCI Express bus and multicore-optimized driver and application software. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PXIe‑6355 is well-suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
PCI Digital IO Board
-
*Bus Interface: PCI Bus*Counter/Timer: 16 Channels*Counter Size: 32 bit*Max. Source Frequency: 80MHz*Compatibility: 5 V TTL/CMOS*Discrete Inputs: 24 Channels*Discrete Outputs: 24 Channels*Pulse Generation: 12 Channels*Bi directional I/O's: 8 Channels*Oscillator stability: 50 ppm*Op-to isolation for I/O's*DMA buffered operation*16-bit data bus 32 bit Address bus for External Memory Interface*The Pulse Width and PRI of the pulses can be varied*The pulse generation frequency from 10Hz to 40MHz (25ns to 100msec)*The no. of pulses controlled from 1 to 255 pulses*All the pulse input and the output signals and Bi-directional write signals driven through Pin Driver*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
Product
RISC-based DIN-rail Fanless Embedded System With I.MX 6UL Processor, COM, CANbus, 2 LANs And DIO (2-in/1-out)
IFB112
-
The IFB112.supports the low power consumption NXP (Freescale) i.MX6UL ARM® Cortex™-A7 528MHz SoC. The design concept of IFB112 is aiming to meet the demands of mission-critical applications. The gateway controller with IP30-rated aluminum and steel enclosure supports an extended operating temperature ranging from -40°C to 70°C, a wide voltage range of 9V - 48V DC power input with terminal block, and has been designed to withstand vibration up to 5G. For system integrators with wireless communication needs, the IFB112 has one PCI Express Mini Card slot, one SIM card slot, and two internal antennas. It supports one serial port, two LANs and one CANbus port to enable fast and efficient data acquisition and communication. Its digital I/O port provides users with a convenience of digital devices connection.
-
Product
64-CH, 12/16-Bit, Up to 3 MS/s Multi-Function PXI Modules
PXI-2200 Series
Multifunction I/O
ADLINIK PXI-2204, PXI-2205, and PXI-2206 are high-density, high-performance multifunction PXI modules. These devices can sample up to 64 AI channels with various gain settings and scan sequences---making them ideal for high-density analog signals with various input ranges and sampling speeds. These devices also offer a differential mode for 32 AI channels to achieve maximum noise elimination. The PXI-2200 series also features analog and digital triggering, 2-CH 12-bit analog outputs with waveform generation capabilities, 24-CH programmable digital I/O lines, and 2-CH 16-bit general-purpose timers/counters.
-
Product
Rugged Analog I/O Modules
-
Our extensive line of analog I/O modules currently includes PC/104, PCIe MiniCard and FeaturePak form-factor products, providing both A/D and D/A functions. Most of these products also include digital I/O and counter/timer features. A unique feature of Diamond analog I/O modules is our patented autocalibration technology, which can reduce analog measurement errors by up to 10 times relative to conventional designs.
-
Product
PCI Express 16 Reed Relay Output
8004e
-
The 8004e PCI Express digital I/O interface provides 16 optically isolated inputs and 16 Reed relay outputs. The isolated inputs protect the PC and other sensitive equipment from the voltage spikes and ground loop currents that are common to industrial environments. The outputs provide high quality, long-life, dry contact switch closures suitable for low-current applications.
-
Product
24-Channel Digital I/O With Digital Integration Features On PCI Express Mini Card
mPCIe-DIO-24A
-
The mPCIe-DIO-24A is a type F1 PCI Express Mini Card (mPCIe) and optional cable assembly (D-Sub 37-pin Male connector) designed to be easily panel-mounted in any application environment. It uses the high speed PCI Express bus to transfer digital data to and from the card. The digital I/O is compatible with 8255 PPI chips making it easy to program. This also allows for simple and trouble-free migration from other ACCES PCI and PCI Express digital I/O cards, but also provides for advanced features enabled by the onboard FPGA logic.
-
Product
PXI-6733, 16-Bit, 8-Channel, 1 MS/s PXI Analog Output Module
778512-01
Analog Output Module
16-Bit, 8-Channel, 1 MS/s PXI Analog Output Module—The PXI‑6733 is a high-speed analog output device designed to deliver simultaneous, multichannel updates for control and waveform output applications, such as stimulus-response tests (including acoustic distortion testing) and simulation (such as three-phase power simulation). In addition, the device provides eight 5 V TTL/CMOS digital I/O lines; two 24‑bit, 20 MHz counter/timers; and digital triggering and external clocking capabilities. The PXI‑6733 can replace several kinds of instruments, including stand-alone proportional integral derivative (PID) controllers, low-speed arbitrary waveform generators, and function generators. You can control each data point for each channel to define common waveforms, such as square, sine, or sawtooth, as well as complex waveforms.
-
Product
Datalogger
iLOGPlus
-
Infinite Industrial Informatics Lt
iLOGPlus RTU/Data Loggers are internet enabled devices, specially suited for remote data acquisition, distributed telemetry and remote control. The units act as master devices and send alerts and data files on their own via FTP, email and SMS. All types carry a built-in TCP/IP webserver with live webpages that can be accessed by any Internet browser application. They accept and serve TCP and SMS commands for interactive operation in a SCADA system.Analog inputs and digital I/O are expandable by means of I/O expansion modules, plugging on a serial I/O expansion bus.
-
Product
cDAQ-9181, 1‑Slot, Ethernet CompactDAQ Chassis
781496-01
Chassis
1‑Slot, Ethernet CompactDAQ Chassis - The cDAQ‑9181 is a CompactDAQ Ethernet chassis designed for small, distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The chassis also has four 32‑bit general‑purpose counters/timers. You can access these counters through an installed, hardware‑timed digital C Series module for applications that involve quadrature encoders, PWM, event counting, pulse train generation, and period or frequency measurement.
-
Product
Digital Input/Output Expander (Open-Collector Outputs)
ENVIROMUX-DI16DO16
-
Adds 16 digital inputs and 16 digital open-collector outputs to the ENVIROMUX-2D/5D/16D. Interfaces with the ENVIROMUX-2D/5D/16D via the RJ45 Sensor Port. Digital inputs: 16 screw terminal pairs for connecting dry contact devices; One screw terminal pair for tachometer; 0 to 255 Hz. Accepts 26 to 16AWG wire. Potential free. Voltage range: 0 to +36VDC. Over-voltage surge protected. Digital outputs: 16 screw terminal pairs for open-collector outputs. Accepts 26 to 16AWG wire. Rated sink current: 500 mA per output. +5VDC, 22kΩ pull-ups. Voltage range: 0 to +24VDC. Over-voltage surge protected. Supports CAT5/5e/6 cable up to 500 ft. (152.4 m). Powered by ENVIROMUX-2D/5D/16D. Compatible with ENVIROMUX-2D/5D/16D. Dimensions WxDxH: 6.49x3.10x1.08 in (165x79x27 mm). Regulatory approvals: RoHS.
-
Product
Mixed Signal, Multi-Functional Test Module
PXIe-ScanIO-112
Test Module
The PXIe-ScanIO-112 delivers a powerful combination of digital, analog, and AC-coupled testing in a single PXIe module. With 104 boundary-scan controllable digital I/O channels and 8 analog I/O channels ranging from –15V to +15V, engineers gain the flexibility to test a wide variety of board-level designs. The module supports IEEE-1149.6 AC-coupled interconnect testing, configurable single-ended and differential pin operation, and integrates seamlessly with the Corelis ScanExpress™ suite.
-
Product
Isolated Digital Input/Output Card
PCI-IDIO-16
-
The PCI-IDIO-16 is a low-cost, 6.8" card that provides isolated input and output for PCI-bus computers. The card has sixteen optically-isolated digital inputs for AC or DC control signals and sixteen isolated FET outputs. For safety reasons in working with AC voltages, insulating shields are provided with each card.
-
Product
USB-6366, 8 AI (16-Bit, 2 MS/s), 2 AO (3.33 MS/s), 24 DIO USB Multifunction I/O Device
781445-02
Multifunction I/O
8 AI (16-Bit, 2 MS/s), 2 AO (3.33 MS/s), 24 DIO USB Multifunction I/O Device - The USB-6366 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard … NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB-6366 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
DIOS (Digital I/O Scan Module)
JT 2122/MPV
Digital I/O Module
The JT 2122/MPV DIOS (digital I/O scan module) increases the coverage and improves the diagnostic resolution of boundary-scan testing by extending test access to connectors and/or test points. JT 2122/MPV DIOS provides bi-directional parallel-scan access to up to 128 or 133 I/Os in a standard DIMM-168 module.
-
Product
USB-6346, 8 AI (16-Bit, 500 kS/s), 2 AO (900 kS/s), 24 DIO USB Multifunction I/O Device
785815-01
Multifunction I/O
8 AI (16-Bit, 500 kS/s), 2 AO (900 kS/s), 24 DIO USB Multifunction I/O Device - The USB-6346 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB-6346 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Pico-ITX SBC With Intel® Atom® X5-E3940 Processor, DisplayPort, LVDS, 2 GbE LAN And Audio
PICO319
-
The PICO319 is powered by the onboard Intel® Atom® x5-E3940 quad-core processor. The noise-free pico-ITX motherboard offers combinations of ruggedness, high computing capabilities and enhanced graphics capability in an extremely compact size of only 100 x 72 mm. Moreover, the board features 12V DC power supply input with AT Auto Power On function. A dual-display capability is available through DisplayPort and 18/24-bit single/dual channel LVDS ports. For extensive storage needs, this compact embedded motherboard has one M.2 Key B slot (22 x 42 mm or 30 x 42 mm) for SATA or PCIe x2 SSD card and one half-size PCI Express Mini Card slot in support of mSATA. The Intel® Atom®-based pico-ITX board comes with rich I/O connectors, including two USB 2.0 ports, two USB 3.0 (USB 3.1 Gen1) ports, one RS-232/422/485 port, one RS-232 port, one HD Codec audio, and 4-channel digital I/O. It also supports SMBus that is compatible with I2C for smart battery support. The PICO319 offers watchdog timer and hardware monitoring function for reliable operation.
-
Product
PXI-6122, 4 AI (16-Bit, 500 kS/s/ch), 8 DIO, PXI Multifunction I/O Module
779179-01
Multifunction I/O
4 AI (16-Bit, 500 kS/s/ch), 8 DIO, PXI Multifunction I/O Module—The PXI‑6122 is a simultaneous-sampling, multifunction data acquisition device. It offers analog input, digital I/O, two 24‑bit counters, and digital triggering. The PXI‑6122 is ideal for a variety of applications, such as IF digitization; transient recording; ISDN, ADSL, and POTS manufacturing test in the telecom industry; ultrasound and sonar testing; and high-energy physics. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Pico-ITX SBC With Intel® Pentium® Processor N4200/Celeron® Processor N3350, DisplayPort, LVDS, 2 GbE LAN And Audio
PICO318
-
The PICO318 is powered by the Intel® Pentium® processor N4200 or Celeron® processor N3350. The PICO318 is a low power-consumption 2.5-inch embedded board that is expandable, rugged design, feature-rich and versatile to help facilitate quick deployment. The PICO318 is equipped with one 204-pin DDR3L-1867 SO-DIMM for up to 8GB system memory. A dual-display capability is available through 18/24-bit single/dual channel LVDS and DisplayPort. For storage, there are one M.2 key B slot for SATA or PCIe x2 SSD card and one half-size PCI Express Mini Card slot with support for mSATA. Moreover, the pico-ITX form factor single board computer features 12V DC power supply input with AT Auto Power On function. The Intel® Apollo Lake-based pico-ITX board provides rich I/O connectivity including two USB 3.0 ports, two USB 2.0 ports, one RS-232/422/485 port, one RS-232 port, two Gigabit LAN ports with Intel® i211AT Ethernet controller, one HD Codec audio, and 4-channel digital I/O. The PICO318 is suitable for various industrial environments with an operating temperature range of -20°C to +60°C.
-
Product
Multi-Spectral Intrusion Solution
Saros™ DH-390 Dome
-
The FLIR Saros™ DH-390 Dome combines multiple traditional perimeter protection technologies into a unified solution that delivers accurate, actionable alerts and verified alarm data. The Saros DH-390 includes multiple FLIR Lepton thermal sensors, a 1080p camera, IR and visible LED illuminators, advanced onboard analytics, two-way audio, and digital I/Os. FLIR Saros enables businesses to implement reliable, state-of-the-art outdoor intrusion detection in a cost-effective manner by minimizing the equipment required and reducing false alarms.
-
Product
D10-AIO Conversion Set_for Conventional Panel-mounted Type Power Amplifier
PAD24
-
PAD24 DIO(digital input/output)-AIO(analog input/output) Conversion Set Conversion Set products. It could be used for DIO (Digital input/output) conversion and galvanic isolation between Real-time simulation system and protection equipment, and another equipment which need AIO (analog binary input/output, dry contacts).
-
Product
PXI-6229, 32 AI (16-Bit, 250 kS/s), 4 AO, 48 DIO, PXI Multifunction I/O Module
779115-01
Multifunction I/O
32 AI (16-Bit, 250 kS/s), 4 AO, 48 DIO, PXI Multifunction I/O Module—The PXI‑6229 offers analog I/O, correlated digital I/O, two 32‑bit counter/timers, and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
80-Channel Reconfigurable Digital PMC
2979
-
The 80-channel Reconfigurable Digital I/O PMC provides a vehicle for implementing complex user-specific digital designs requiring high speed single-ended operation. 64 of the 80 signals are available out the PN4 connector, while all 80 signals are wired to the front panel connector.
