ISO
International Standards Organization
-
Product
Room Acoustics Analysis on iOS
RoomScope
-
RoomScope turns your iPad, iPhone, or iPod touch into a room acoustics measurement and analysis tool. With RoomScope, you can measure a room impulse response and then calculate reverberation time, early decay time, clarity, and definition, as defined in the ISO 3382 standard. RoomScope also allows you to adjust the Schroeder decay curve integration limits with the touch of your finger and plot the calculated room parameters versus whole or 1/3-octave band center frequency.
-
Product
Functional Testing For Critical Software
RapiTest
-
*Requirements-based testing for Ada, C & C++ on-host & target*Reduce test authoring effort through easy-to-use test formats*Manage project artifacts with requirements traceability*Simplify verification through integration with your CI tool*Produce evidence for DO-178 and ISO 26262 certification
-
Product
Band Pass Filters
-
*High power handling 200W with a wide range of bands available*Excellent Isolation with Low Intermodulation*High reliability of >500K Hours MTBF and multi-strike lightning protection*Support for 7-16 or 4.3-10 connectors and optional 19 inch rack mount kit*Designed and produced to ISO 9001:2008 certification standards for reliability and quality
-
Product
Horizontal Flammability Tester
UI-TX40
-
Horizontal Flammability Tester – Horizontal Flammability Chamber is used to test textile and material used in vehicles horizontal burning rate when exposure to a small flame. Horizontal Flammability Test Method includes ISO 3795, ASTM D5132, JIS D1201, SAE J369, FZ/T01028, GB/T8410, GB/T20953 and etc.
-
Product
Mass Flow Calibration
-
Allow instrument interchangeability without affecting your process and meet ISO 9001 requirements easily and efficiently with Process Instruments’ Mass Flow Calibration and Repair Services.
-
Product
Hardness Test Blocks, Indenters & Accessories
-
Qualitest offer the largest Hardness Test Block selection in the industry. If you don't see what you're looking for, please call our sales department. All of our Hardness Test Blocks come with Certification. All the blocks are calibrated and accredited to ISO guide 25 and will meet automotive and aerospace standards. The HRC test blocks are calibrated on the new NIST level.
-
Product
PCBA & Bare Board Cleanliness Tester
Zero-Ion G3
-
For two decades, thousands of electronics assemblers have relied on the Zero-Ion cleanliness testing to verify the cleanliness of post-reflow printed circuit assemblies and bare boards. Over time, as PCB assemblies have become more complex and more densely populated with surface mount components, and as vigorous quality standards such as ISO, TQM and Six Sigma have become commonplace, the ability to meet—and confirm—cleanliness levels has grown in importance. The Zero-Ion ROSE tester has kept pace with customer requirements, and the Zero-Ion G3 is the most advanced Zero-Ion ever designed, capable of testing assemblies reflowed with any solder paste, including no clean—yet its also one of the most affordable cleanliness testers on the market as well, with performance and ease of use second to none.
-
Product
NFC Conformance Test System
T3111S
Test System
The T3111S RIDER NFC Conformance Test System is the Keysight solution for RF Analog and Digital Protocol testing of NFC, EMV and ISO devices. The Test System is based on the Keysight T1141A NFC Test Set and it is complemented by the Keysight's or FIME's robots for accurate and repeatability RF testing. Selected 3rd party positioning robots can also be supported.
-
Product
Insulation Meters
-
Here you will find an insulation tester for a variety of ranges between 50 mega ohms and 2000 mega ohms. The portable manual insulation tester is used for determining insulation resistance, continuous current, alternating current and testing. With an insulation tester, measurements can be taken for different voltages, beginning with 100V up to 10,000V. Measurements meet the DIN VDE 0413 part 1 standard. The insulation tester comes with a test mechanism, clips, batteries and a carrying case. The insulation meter can be equipped for test laboratories if an optional DIN EN ISO is acquired.Measurement of insulation in cables and motor coils is vitally important for the prevention of accidents and damage to installations and is obligatory according to most codes of conduct.
-
Product
Cleanroom Testing
-
MicroStat Laboratories -R.E.T.S.
We utilize the relevant test methods and standards set forth by the ESD Association, ANSI, ASTM, NFPA, IEST, IEC, ISO, or our clients’ in-house specifications. ESD testing is performed in-house; other testing can be arranged through sub-contractors with interpretation of results performed by experienced contamination control experts..
-
Product
Bluehill® Universal Software
-
Bluehill Universal from Instron is a modern, touchscreen‐first software platform designed to make materials testing simpler, smarter, and safer. With intuitive, guided workflows, prebuilt method templates for ASTM, ISO, and EN standards, and dynamic features like barcode integration, pass/fail display, and conditional logic, it streamlines testing tasks and reduces user error. For more advanced users, modular options—such as TestProfiler for cyclic tests, Traceability for full audit trails and 21 CFR Part 11 compliance, and seamless API support—enable customization, data integrity, and lab‑wide connectivity. Whether deployed on new Instron systems or retrofitted into existing hardware, Bluehill Universal offers enhanced usability, robust security, and flexible data handling for next‑generation materials testing labs.
-
Product
Calibration Services
-
Edgetech Instruments Inc. has the ability to calibrate any hygrometer (Edgetech Instruments or other manufacturers)Edgetech Instruments performs NIST traceable calibrations and is compliant with ANSI/NCSL Z540-1 and ISO 9001Calibration capabilities include 0-95%RH, dew points down to -75C, traces of oxygen to 10ppm
-
Product
Magnetic Stripe Analysers
-
Companies who aim to deliver the highest quality magnetic media products to their clients choose Barnes Magnetic Stripe Analysers. They are used by magnetic stripe card producers, card and ticket manufacturers and bureaus for ISO and CQM testing, production quality control, encoding equipment maintenance and development.
-
Product
HV Enclosures with Integrated Safety Test
-
The HV test hood according to Performance Level e (ISO 13849-1), developed by us according to the EN50191 standard (erection and operation of fixed and temporary electrical test installations), offers the highest safety for the operator. The large test chamber is enclosed with a hood made of sturdy, highly insulating and transparent plastic. During the test, there is a clear view of the test specimen. A signal light visually indicates safe opening when the light is “green”. “Red light” symbolises danger, the hood cannot be opened due to the safety interlock. The safety switch also ensures that the hood cannot be opened during the test. This means that the test hood fulfils all the required specifications for compulsory contact protection.
-
Product
Coating Thickness Gauge for Ferrous and Non-Ferrous Materials
CM8856
-
* It meets the standards of both ISO2178 and ISO 2361 as well as DIN, ASTM and BS. It can be used both in the laboratory and in harsh field conditions.* The F probes measure the thickness of non-magnetic materials (e.g. paint,plastic, porcelain enamel, copper, zinc,aluminum , chrome etc.) on magnetic materials (e.g. iron, nickel etc.) . often used to measure the thickness ofgalvanizing layer, lacquer layer, porcelain enamel layer, phosphide layer, copper tile, aluminum tile, somealloy tile, paper etc.The N probes measure the thickness of non - magnetic coatings on non-magnetic metals .It is used on anodizing, varnish, paint, enamel,plastic coatings, powder, etc. appliedto aluminum, brass, non-magnetic stainless steel, etc.* Automatic substrate recognition.* Manual or automatic shut down.* Two measurement mode: Single andContinuous* Wide measuring range and highresolution.* Metric/Imperial conversion.* Digital backlit display gives exactreading with no guessing or errors.* Can communicate with PC computerfor statistics and printing by theoptional cable.* Can store 99 groups of measurements.* Statistics is available.2.SPECIFICATIONSDisplay: 4 digits LCD, backlitRange: 0~1250 μm/0~50mil(other ranges can be specified )Min.radius workpiece: F: Convex 1.5mm/Concave 25mmN: Convex 3mm/ Concave 50mmMin. measuring area: 6mmMin.Sample thickness : 0.3mmResolution: 0.1 μm (0~99.9μm);1 μm (over 100μm)Accuracy: ±1~3%n or 2.5 μm or 0.1mil(Whichever is the greater)Bttery Indicator: Low batter indicator.PC interface: with RS-232C interfacePower supply: 2x1.5 AAA(UM-4) batteryOperating condition: Temp. 0~50℃ .Humidity <95% .Size: 126x65x35 mm; 5.0x2.6x1.6 inchWeight: about 81g(not including batteries)Standard accessories:Carrying case ...................1 pc.Operation manual ............ 1 pc.F probe in built .................1 pc.NF probe in built...............1 pc.Calibration foils ..............1set.Substrate (Iron) ................1 pc.Substrate (Aluminium)......1 pc.Optional accessories: RS-232C cable & software:1.USB adaptor for RS-232C2.Bluetooth interface
-
Product
Calibration Equipment
-
Calibration is the method of comparing tools and measuring devices to higher accuracy standards. Torque calibration equipment is the official means by which torque testers and sensors are calibrated and are traceable to National or International Standards, such as N.I.S.T and ISO. In order to maintain precision accuracy, it is essential that torque measuring equipment be calibrated regularly. By equipping your team with Mountz calibration equipment, you can avoid the costly chore of sending your torque tools to the lab whenever they fall out of alignment.
-
Product
2.4mm Connectors
-
Pasternack 2.4mm connector category has mostly RoHS and REACH compliant components. 2.4mm connector products in this category will terminate to coax or terminal. Our 2.4mm connector products are built to precise RF and microwave industry specifications.Pasternack 2.4mm connectors are available in male or female gender with 50 Ohm impedance. 2.4mm connector items are available in threaded, bulkhead, 2 hole panel, 4 hole panel or mountless options. These 2.4mm connector designs include clamp/solder, field replaceable or solder attachment methods.Pasternack Enterprises' ISO 9001:2008 registered facility ships 2.4mm connectors the same day from the broadest and deepest in stock inventory of RF and microwave parts. Excellent customer service and technical support are on hand to support you with 2.4 mm connector questions.
-
Product
Digital Impact Test Machine
-
The Digital Impact Testing Machine mainly used to determine the anti-impact capability and strengthen impact toughness of non metallic materials such as nylon, glass fiber reinforced plastic, ceramic & cast stone, electrical insulating materials etc.Sample and support are easy centeringThe pendulum of the machine can be raised or released automatically by button pressedDigital LCD screen control and value displayThe machine comply with GB / T1843, ISO 180, GB / T21189, GB / T2611 and other international standard
-
Product
Hydraulic Vibration Testers
HV-Series
-
L.A.B.’s HV Hydraulic Vibration Test Systems help you design high quality, cost-effective products and shipping containers by accurately measuring sensitivity to vibration. HV Systems are specifically designed to meet a wide range of ASTM, DOT, ISTA, ISO and federal standards for vibration testing. HV Systems are ideal for a wide spectrum of testing applications ranging from sine sweep tests to the most complex data real time simulation, or random reproduction applications.
-
Product
Scanning Slit Beam Profiling
NanoScan
-
Measure your beam as never before with the NanoScan™ beam profiler. The advantage of scanning slit beam profiling is sub-micron precision for measuring beam position and size. Scan head configurations include Silicon, Germanium, and Pyroelectric versions for a wide range of wavelengths and laser power levels. The NanoScan software is available in two versions: Standard and Professional, and includes an extensive set of ISO quantitative measurements, an M2 Wizard, and the ability to measure laser power.
-
Product
Melt Flow Index Testers
-
Instron® melt flow testers are specifically designed for easy and accurate measuring of Melt Flow Rate (MFR) and Melt Volume Rate (MVR). Our extrusion plastometers range from manual to semi-automated plastic melt flow index testers performing multiple weight tests. All our Melt Flow Index testing equipment meets the latest ASTM and ISO standards.
-
Product
Pendulum Impact Testers
MPX
-
Delivering precision and safety in high-volume materials testing, the MPX pendulum impact system from Instron is optimized for Charpy and Izod testing of metals. Equipped with Bluehill Impact software, it supports capacities from 300 J to 900 J and features motorized hammer lift, automatic return, and interchangeable hammer weights. An enclosed, interlocked safety guard ensures operator protection in compliance with CE and ISO 13849 standards. The system supports key standards including ASTM E23, ISO 148, EN 10045, and others, while offering configurable reports and seamless data export capabilities.
-
Product
Transitions And Iso-adapters
-
Smiths Interconnect offers a wide variety of transitions and Iso-adapters to suit the customer's requirements, up to Ka band.
-
Product
Fast 6-Axis Hexapod
H-900KSCO
-
Physik Instrumente GmbH & Co. KG
Reference-class 6-axis positioning system. Parallel-kinematic design for six degrees of freedom making it significantly more compact and stiff than serial-kinematic systems, higher dynamic range, no moved cables: Higher reliability, reduced friction. Powerful digital controller, open software architecture. Optional: Software for avoiding collisions in restricted workspace. Fields of application. Motion simulation: Motion profile compatible according to ISO 20672, ISO 8728, and ISO 16328. Industrial production, tool machines, automotive industry, shipping.
-
Product
Flexural Test Methods For Plastics: ISO 178 And JIS K 7171
-
Resin materials (plastics) are found in a wide variety of items used on a daily basis. Recently, plastics have started to be used as structural materials in transportation equipment, such as automobiles and aircraft, due to their strength and light-weight nature. In these applications, it is important to understand the mechanical strength properties of these plastics.
-
Product
Systems for Vibration Monitoring and Diagnostics
-
*Reliable permanent vibration monitoring according to DIN ISO 10816*Cost effective real-time vibration monitoring for machine protection*Increase availability and reliability, reduce maintenance costs and ensure quality*Compact field units and modular control cabinet systems*Analog output and switching output for alarm function
-
Product
Mooney Viscometer
SMV-301/301RT
-
The SMV-301 / 301RT allows the user to measure the Mooney viscosity, scorch time, minimum Mooney viscosity, and other characteristics of rubber in accordance with JIS, ISO, and ASTM test methods. With outstanding temperature recovery characteristics and easy operability, it can also be used for stress relaxation measurements or for tests that involve varying the rotor speed.
-
Product
EPOCH 650
-
The large, full VGA transflective display combined with our patented digital high dynamic range receiver provides a stable, striking A-scan representation in any lighting condition. The EPOCH 650 is designed to meet the requirements of ISO 22232-1 and allows a full range of standard and optional flaw detection features.
-
Product
DC Power Supply With Scope, Arbitrary Waveform Generator, And Automotive Application Features Bundle
E36154AGVX
DC Power Supply
The Keysight E36154AGVX consists of a Keysight E36154A DC power supply, a Keysight E36150ADVU Scope View and arbitrary waveform generation (AWG) capabilities, and a Keysight E36150ATMU Automotive Standards Testing Capabilities with Enhanced Programming Speed, ISO Preset Library, Playback Simulation and E-Logging features. The E36154A includes single-output and auto-range capabilities, 30V, 80 A, 800 W, and LAN and USB interfaces.
-
Product
Medical Imaging
-
Teledyne e2v has over 35 years of experience in the medical field and offers medical devices companies a range of CCD and CMOS image sensor solutions and services. We understand the challenges facing the healthcare landscape (including ageing populations and the management of healthcare spending), and through close partnerships with our suppliers, are able to offer customers agility and flexibility over our entire supply chain. This enables us to provide our customers with a fully comprehensive digital imaging solution. We also produce and sell an X-ray intra-oral dental product named Demoniac, which is compliant with ISO 13485.
