Sensor Testers
-
Product
Motion and Sensor Instruments
Trig-Tek™ Instruments
-
In 2010, we acquired the Trig-Tek™ line of innovative, precision, dynamic test and measurement instruments suitable for laboratory, military, and industrial environments. Trig-Tek™ is now a brand of products engineered and manufactured by Astronics Test Systems.
-
-
Product
Pyroelectric Energy Sensors
-
Our pyroelectric energy sensors use innovative, patented technology which facilitates accurate and repeatable laser measurements of pulses over an extensive range of conditions including long pulses to 20 ms.
-
Product
Anaerobic Jar Tester
LD-LAJ-A12
-
Anaerobic JarLD-LAJ-A12with 3.5 L capacity has PMMA transparent, smooth surface jar design. High quality O-ring is used to make tight sealing between jar and lid. Adopted with quick snap-shut coupling, enables quick connection to the system in a one soft move. The number of gas packs needed may vary in brands and pack size, required to create anaerobic condition in the jar.
-
Product
Digital Safety Tester
-
Is equipped with a high-efficiency PWM amplifier, which isolates the influence of external voltage fluctuations and outputs stable high voltage. Even in areas with large voltage fluctuations, it can achieve "safe" and "reliable" measurements.
-
Product
Relay Circuit Tester
RCT76
-
Quickly identify electrical problems in an entire circuit at the push of a button. Test the component on a circuit to determine if it is functioning correctly.
-
Product
NITOS Wireless Sensor Platform
-
The NITOS prototype wireless sensor mote, is comprised of open-source and configurable modules. NITOS mote features the ATmega32u4 microcontroller running at 8MHz and operating at 3.3V. The aforementioned microcontroller is fully compatible with the Arduino platform that enables ease of software development and provides compatibility with several commercial sensing modules. Moreover, the platform is equipped with an Xbee radio interface that enables communication with the respective gateway. The Xbee module is a tiny device ideal for setting up mesh networks and has a defined rate of 250 kbps. This module uses the IEEE 802.15.4 stack which is the basis for theZigbee protocol. Apart from the Xbee module, NITOS mote can also feature a WiFi wireless interface in order to communicate with WiFi gateways. The developed mote currently features specific sensing modules, an air temperature and humidity sensor, a light intensity sensor and a human presencesensor. Various types of sensing modules and actuators can be further integrated exploiting existing Arduino software that implements several existing communications protocols. The firmware can be easily uploaded through the on-board USB connection. Figure 1 illustrates the developed NITOS mote and the respective gateway node.
-
Product
Universal Sensor Mounting Stand
MS-AJ
-
Panasonic Industrial Devices Sales Company of America
Panasonic's Universal Sensor Mounting Stand MS-AJ is an extremely versatile Mounting Stand that is simple to use and easy to adjust.
-
Product
Horizontal Flammability Tester
TF311
-
TESTEX Testing Equipment Systems Ltd.
Horizontal Flammability Tester, to determine the comparative burn rates and burn resistance of textiles, particularly those for automotive interior use. Horizontal flammability tester is safe and easy to operate, Comprises draft free stainless steel cabinet with observation window, sample holder and door mounted burner. Horizontal Flammability Tester complies with ISO 3795, ASTM D5132,FMVSS 302, etc.
-
Product
Adhesion Tester
-
An adhesion tester measures the force required to detach a coating from a substrate. Often called a pull-off adhesion tester or peel tester, an adhesion tester applies a large amount of force to evaluate a coating's bond strength. When measuring peel force or adhesiveness, the nature of the substrate's surface plays a significant role. However, a high-quality adhesion tester features a self-aligning measuring head to compensate for any surface irregularities.
-
Product
Salinity Logger Sensor
NUL-228
-
This sensor enables measurements of the salt content in a solution in three ranges: %, ppm and mg/L.The sensor is pre-set factory calibrated and immediately ready to use.
-
Product
Industrial heat flux sensor
HF05
-
Hukseflux Thermal Sensors B.V.
The HF05 heat flux sensor is used to measure heat flux in industrial environments. It is covered with a stainless steel cover.
-
Product
Cable Tester
-
The MapMaster™ mini detects faults and locations of RJ45 network cables. Good terminations, causes of faults and locations of cables are displayed on an LCD display. A set of five mapping remotes is included for locating cables terminated in wall jacks or patch panels. A built-in tone generator with 4 different tone combinations can be used with a tone probe to detect where a cable is routed and the location of the end of the cable.
-
Product
Combo Tester
750USB
-
The Staticide® 750USB Wrist Strap & Dual Heel Tester measures electrical resistance of wrist straps and heel grounders simultaneously and individually. It can also do what simple pass/fail testers cannot: store the user data and actual resistance readings to a computer. Colored LEDs and a buzzer provide universally understood test results in under three seconds.
-
Product
LED Light Tester
-
The T100L Automatic LED Light Test Equipment is designed to identify the presence of any defects of electronic components for LED light applications, addressing any high-volume production testing challenges without needing expensive test fixtures with fiber optics
-
Product
Inclination & Acceleration Sensors
-
Whether leveling crane trucks, monitoring the condition of large systems, or controlling the acceleration of elevators - the areas of application for inclination and acceleration sensors from Pepperl+Fuchs are diverse. Even in harsh outdoor conditions, they always guarantee precise measurements.
-
Product
IK Level Tester
IK07-10
-
IK ratings are defined as IKXX, where “XX” is a number from 00 to 10 indicating the degrees of protection provided by enclosures (including luminaires) against external mechanical impacts. The different IK ratings relate to the ability of an enclosure to resist impact energy levels measured in joules (J). IEC 62262 specifies how the enclosure must be mounted for testing, the atmospheric conditions required, the quantity and distribution of the test impacts and the impact hammer to be used for each level of IK rating. The IK test applicate on lighting luminaires test according to IEC60598 (GB7000) and IEC60068-2-75 (GB2423.55).
-
Product
Qualification Tester
LQ402
-
Computer Gesteuerte Systeme GmbH
The qualification tester LQ402 is designed to support up to 6 DUTs (Device under Test), for which the loads are installed in separate load boxes. The system consists out of 2 cabinets. One is for the electronic components with the primary measurement devices and the other one holds the 6 load boxes.
-
Product
Transformer Performance Tester
JYM
-
JYM insulation resistance tester is used for on-site insulation resistance measurement. The instrument has built-in positive and negative bipolar high-voltage power supplies, with large output power and strong load capacity. It is suitable for insulation resistance measurement of samples with large capacitance, such as power transformers and cables.
-
Product
IEC60065 Socket Torque Balance Tester Torsion Tester
-
Shenzhen Chuangxin Instruments Co., Ltd.
*Plug and Socket Torque Tester/Device is for compliance is checked by engaging the device, as during intended use, with the socket-outlet of a test apparatus. *Plug Torque Tester/Equipment is a device provided with pins intended to be introduced into fixed socket-outlets shall not impose undue strain on these socket-outlets.The balancing arm of the test apparatus pivots about a horizontal axis through the centre lines of the contact tubes of the socket-outlet at a distance of 8 mm behind the engagement face of the socket-outlet.*With the machine not in engagement, the balancing arm is in equilibrium, the engagement face of the socket-outlet being in the vertical position.After the device has been engaged, the torque to be applied to the socket-outlet to maintain its engagement face in the vertical plane is determined by the position o a weight on the balancing arm.
-
Product
Saw Mark Tester
SRT-301
-
SRT-301 Saw Mark Tester is used to Measure Line-mark depth of the wafer surface,it has the advantages such. As easy carried, Conveniently operated Liquid crystal display, energy conservation and so on, At the same time,it has the built-in printer and rechargeable batteries , All design are up to the standards of JIS,DIN,ISO,ANSI.
-
Product
Hydrostatic Head Tester
-
TESTEX Testing Equipment Systems Ltd.
Hydrostatic Head Tester is used for measures the resistance of a fabric to the penetration of water under hydrostatic pressure. Hydrostatic Head Tester complies with AATCC 127, EN 20811, ISO 1420A, etc. Please contact us for Hydrostatic head test procedure.
-
Product
Phase Rotation Testers
-
Our range of phase sequence indicators provide LED indicationof rotation. They are perfect for checking phase sequence in motors, pumps and air conditioning units.
-
Product
Outdoor Temperature Sensor
ENVIROMUX-STS-O
-
Applications from -40 to 185°F (-40 to 85°C). Accurate to within ±0.9°F (±0.5°C). Weatherproof enclosure. High resistance to external influences on the cable due to digital output signal. Re-calibration is not necessary after initial set-up. Quick release waterproof RJ45 connector. Supports CAT5/5e/6 cable up to 1,000 ft. (305 m). Powered by ENVIROMUX-2D/5D/16D. MTBF: 1,942,123 hrs. Compatible with ENVIROMUX-2D/5D/16D. Regulatory approvals: CE, RoHS.
-
Product
Temperature Sensors
-
Premier Electrosystems manufactures a wide range of temperature sensing devices, thermocouples, R.T.D sensors and temperature transmitters. We manufacture Thermocouples like E, J, K, N, T, S, R, and B and R.T.D's like Pt-100, Pt-200, Pt-500, Pt-1000. Our sensors come in different forms, types, ranges, and varieties to suit each application. All our products are supplied with calibration certificates and traceable to national and international standards.
-
Product
Microwave Leakage Tester
TEK500
-
An easy to use, low cost pass / fail microwave leakage detector suitable for commercial and domestic microwave ovens. It is designed to comply with national standards on permitted exposure levels. The TEK500 includes a self test which simulates a real microwave input to ensure the unit is working correctly at all times.
-
Product
Digital ELCB Tester
KM 1812 EL
-
Kusam Electrical Industries Limited
* 2 Lines x 16 Characters L.C.D.* Very Low Power Consumption.* Microprocessor Controlled.* Menu Driven.* Accurate digital readout of disconnection Time.
-
Product
Pressure/ Vacuum Sensors
-
There are three different types of pressures that can be measured using Premier Electrosystems' Pressure Sensors: Gauge, Absolute, and Differential. Gauge pressure is the pressure measured relative to the ambient atmospheric pressure.A typical application for a gauge pressure sensor is to measure liquid levels in a vented tank using the difference in hydrostatic pressure and ambient atmospheric pressure. Absolute pressure sensors will give the result relative to zero (a perfect vacuum). This is useful in applications where there is a direct effect of altitude on the pressure being measured. Differential pressure sensors measure the difference in pressure between two points. Differential pressure sensors are often used to monitor airflow in HVAC applications.
-
Product
Advanced Imaging CMOS Image Sensors
AI Series
-
Focusing on high-end imaging series CMOS image sensors for new security applications based on customer needs
-
Product
Barometric Pressure/Temperature/Altitude Sensor
BMP180
-
This precision sensor from Bosch is the best low-cost sensing solution for measuring barometric pressure and temperature. Because pressure changes with altitude you can also use it as an altimeter! The sensor is soldered onto a PCB with a 3.3V regulator, I2C level shifter and pull-up resistors on the I2C pins.
