Extender Cards
move out from slot circuit card giving access thereof.
See Also: Extender Boards, Cards, Bus
-
product
PCI High Density Pecision Resistor Card, 9-Channel, 2Ω To 470Ω
50-298-114
The 50-298-114 is a high density programmable resistor card with 9 channels which can be set between 2Ω and 470Ω with 2Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PXI 8-Slot BRIC 192x8 Matrix, 2A 2-Pole (8 sub cards)
40-565A-102-192X8
The 40-565A PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps at 150VDC/100VAC The 40-565A BRIC modules are available in 2, 4 or 8 slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using quality electro-mechanical relays for high switching confidence.
-
product
PXI 2-Slot BRIC 24x8 Matrix, 2A 2-Pole (1 sub card)
40-565A-202-24X8
The 40-565A PXI Matrix BRIC is a range of high-density matrix modules able to switch up to 2 Amps at 150VDC/100VAC They are available in 2, 4 or 8 slot PXI sizes to suit most high-performance PXI Matrix requirements and constructed using quality electro-mechanical relays for high switching confidence.
-
product
PCI Multiplexer Cards
*High-density 4-bank, 24-channel, 2-pole multiplexers*2 Amp multiplexer range with 18 configurations between single 64-channel 1-pole and quad 8-channel 2-pole*High-density multiplexers with switching formats between 5-channel, 32-pole and 198-channel, 1-pole*High-voltage multiplexers designed for cable testing applications*Supported our eBIRST Switching System Test Tools, these tools provide a quick and simple way of finding relay failures our switch systems.
-
product
ABex Terminal Module for Göpel 1149Cx-FXT BSCAN Cards
ABex TM-1149Cx-FXT
The ABex TM-1149Cx-FXT is an ABex terminal module for the Göpel Boundary Scan Controller SFX/PXI(e) 1149/C4-FXT-X. It is connected to the BSCAN-Controller with an adapter-paddle-card.In combination with the above Göpel Boundary scan card it’s possible to connect up to four JTAG/Boundary Scan TAPs. All differential signal wires on the PCB are impedance controlled. In addition, all other digital signals (PIP, TRG, Aux, I/O) and Ground can be switched off via relays.
-
product
FPGA PXIe High-Performance Digital I/O Card
GX3700e
The GX3700e is a user configurable, FPGA–based, 3U PXI Express card offering 160 digital I/O signals which can be configured for single-ended or differential interfaces. The card employs the Altera Stratix III FPGA, which can support SerDes data rates up to 1.2 Gb/s, digital I/O clock rates of 700 MHz, and features over 45,000 logic elements and 1.836 Kb of memory. The GX3700e is supplied with an integral expansion board providing access to the FPGA’s 160 I/Os. Alternatively, users can design their own custom expansion cards for specific applications - eliminating the need for additional external boards which are cumbersome and physically difficult to integrate into a test system. The design of the FPGA is done by using Altera’s free Quartus II Web Edition tool set. Once the user has compiled the FPGA design, the configuration file can be loaded directly into the FPGA or via an on-board EEPROM.
-
product
PCI Strain Gauge Simulator Card, 2-Channel, 350 Ohm
50-265-012
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
product
Digital I/O Card w/CoS IRQ
PCIe-DIO-24HS
This product is a x1 lane PCI Express digital I/O board available in two models. The PCIe-DIO-24H is the basic DIO and the PCI-DIO-24HS features advanced change-of-state (COS) detection capabilities. The card emulates an 8255 compatible chip, providing 24 DIO lines. The DIO lines are grouped into three 8-bit ports: A, B, and C. Each 8-bit port is configured via software to function as either inputs or outputs. Port C can be further broken into two 4-bit nybbles via software and configured as either inputs or outputs.
-
product
SD Card V.4.1 & UHS-II PHY
SD 4.1 Total Solution
To meet the ever increasing data transfer rate in high end applications, such as professional broadcasting transmission or advanced high resolution display, the SD 4.1 specification calls out the maximum performance of 1.56 Gbps at UHS-II full duplex mode per lane or half duplex UHS-II at 3.16 Gbps. In real applications, due to the system overhead and different SD 4.1 device controller designs, the actual measured performance can vary dramatically from system to system. With the newly introduced ADMA 3, the OS driver is now able to issue multiple read or multiple write commands at once, without having to wait for the SD controller to complete one command at a time. Once the SD host controller has collected multiple commands, it will then manage and complete them without intervention from the host software drive. Thus, the UHS-II 1.56 Gbps interface can be more effectively utilized and maximize the system throughput. This feature can be very useful when running multithreaded applications where multiple applications are constantly updating their status or swapping their contents by writing or reading small chunk of data to or from the memory card.
-
product
GPIB PC/104 Interface Card & Cable
GPIB-PC104-XL
The ines GPIB PC/104 interface card uses the enhanced features of the ines GPIB chip , resulting in a reliable solution for industrial measurement.
-
product
3U CompactPCI® 4 RJ45 Port Gigabit Ethernet Card
MIC-3958
Advantech MIC-3958 Series, a 3U height 4HP CompactPCI® peripheral card, using Intel® i210 Ethernet controller, to support up to four RJ45 Gigabit lan connectors, two switchable with rear transition module; MIC-3958A provides four RJ45 lan ports on front panel, MIC-3958R provides two RJ45 lan ports on rear IO panel. Its ideal power solution make it perfect for all fanless system applications.
-
product
DVI Extender with IR and Stereo Audio Options via One CAT5/6/7
ST-C6DVI-300
The XTENDEX® DVI Extender transmits digital DVI video up to 300 feet away from a DVI source over a single CAT5/6/7 cable. Each video extender consists of a local unit that connects to a single link digital DVI source and optional IR emitter, and a remote unit that connects to a DVI display and optional IR receiver.
-
product
MIL-STD-1553 Fiber Optic Bus Extender
FO-1553
Avionics Interface Technologies
Extends MIL-STD-1553 bus access to over 1 mile for remote access - Dual redundant, single and dual stream options available - Both Transformer and Direct coupling modes supported - Uses fiber optic 1.0625 Gbps data rates for low latency over long distances - Optical signaling is not affected by electrical noise and interference - Simple and easy to use solution, no software setup or configuration required - Ideal for applications where test equipment is separated from UUT
-
product
Graphics & Video Cards
Curtiss-Wright Defense Solutions
Designing a graphics-intensive application isn't an easy feat. Curtiss-Wright graphics and video modules reduce costs, speed time-to-market, and reduce program risk by providing low-power, high-reliability, rugged SWaP-optimized solutions based on modular open systems approaches.
-
product
16-CH 12-Bit 110 kS/s Multi-Function DAQ Card
PCI-9112
- Supports a 3.3 V or 5 V PCI bus- 12-bit A/D and sampling rate up to 110kS/s- 16-CH single-ended or 8-CH differential inputs- On-board A/D FIFO
-
product
Cover Extend Feature, GTE 10.00p
K8217B
Cover-Extend Technology (CET) extends the measurement capability of VTEP or nanoVTEP into powered testing by using the Boundary Scan output cell to test the connectors and socket signal pins. This capability extends the Boundary Scan limited access solution on non-boundary scan devices with the use of VTEP or nanoVTEP and CET signal conditioner card hardware.
-
product
Four Channel Clock Driver Card
PI-41401
The PI-41401 is a four channel Clock Driver card capable of operating up to 140 MHz at 3V and 100 MHz at 5V amplitudes into a 50 Ohm load. The PI-41401 has a clock rate of 90 MHz at an amplitude of 5 volts into a 1-MOhm load. Into a high impedance load the output voltage range is from –5 volts to +8 volts with the pulse amplitude ranging from 0V to 9V. When driving a 50 load the voltage range is –2.5 volts to 4.0 volts with the pulse amplitude ranging from effectively 0V to 4.5V. Each channel has a common edgespeed control to vary the rising and falling edges of the output waveform. The adjustable slew rate range, for any amplitude, is the minimum edgespeed of that amplitude times 5. The output pulse amplitude and the load being driven determine the range of variability.
-
product
VME Generic Carrier Card For PMC(PCIbus Mezzanine Card) Modules
AVC-2
VME64x (6U) generic carrier card for PMC (PCIbus mezzanine card) with 2 PMC slots. Modular solution combines any AIM PMC module for AFDX®/ARINC664P7, ARINC429, MIL-STD-1553 or any standard 3rd party PMC module.
-
product
Dual-port Isolated CAN Interface Cards
PCI-7841/cPCI-7841
The PCI-7841/cPCI-7841 is a Controller Area Network (CAN) interface card. It supports a dual-port CAN's interface that can run independently or bridged at the same time. The built-in CAN controller of this card is Philips SJA1000, which provides bus arbitration and error detection with auto correction and re-transmission function.
-
product
PCI High Density Pecision Resistor Card, 18-Channel, 2Ω To 62.1Ω
50-298-011
The 50-298-011 is a high density programmable resistor card with 18 channels which can be set between 2Ω and 62.1Ω with 0.25Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
2-port/4-port PCI Express GigE Frame Grabber Card
AX92320
The AX92320 supports PCI Express x4 lane, two or four independent Gigabit 802.3at (PoE, Power-over-Ethernet) compliant Ethernet ports and GigE Vision camera compliance. The PCI Express x4 frame grabber can provide up to 30 watts at 54 VDC power to port which allows power to be supplied to connected PoE-based devices, such as GigE Vision cameras in machine vision systems. The intelligent GigE Vision card also supports IEEE 1588 (precise time protocol), enabling synchronization with multi-camera acquisition. Combining IEEE 1588 and PoE function, the card utilizes a single Ethernet cable for power, data, and synchronization. Furthermore, it supports jumbo frames up to 9.5KB. The AX92320 is ideal for PoE applications such as automated optical inspection (AOI), factory automation, and PC-based surveillance systems.
-
product
6U Vertical Card
410
VECTOR Electronics and Technology, Inc.
Chassis for vertical card installation
-
product
Dual Channel Driver Card
42460
Two channels of 32 MHz clock drivers with up to 20 volt amplitude. The output voltage range is ±20 V, with independent high and low voltage settings. The inputs to the Card can be optically isolated. The card also contains voltage and current sense capability, which allows muxing of the current or voltage output measurements from all the Driver Channels in the system to a single DVM. The card allows independent programming of the rise and fall time of each channel one nanosecond increments.
-
product
VPX Extender 3U All Differential - Convection / Convection
119EXT3024-07XXR
VPX Test Extender 3U 240mm for convection cooled boards.
-
product
RIBBON 20Pin 0.4M J2 (5 cards)
50-976-020-0.4M
Ribbon Expansion Cable for 50-51x series of PCI matrix cards
-
product
Frequency Extender
DC100
The DC100 system can be installed in the HP8568B(see H96 option below) without compromising the performance of the original instrument. The spectral purity and power accuracy of the primary band ( 100hz to 1.5Ghz) are insured from corruption by careful design of the DC100 system. Additional protection of the primary band is guaranteed as the DC100 system is automatically switched off (all power removed) when in primary band operation.
-
product
PCI Precision Resistor Card 3-Channel, 3Ω To 22.3MΩ
50-297-154
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
64-bit/66 MHz Metering PMC-to-PMC Extender
3954
The extender/analysis probe permits extension of a PMC card beyong the edge of a host processor front panel, providing access to both Side 1 and Side 2 of a PMC under test.
-
product
PCI 8x8 2Amp High Density Matrix Card
50-529-002
The 50-527, 50-528 and 50-529 are a range of PCI single pole matrix cards supporting either 64 or 128 crosspoints using electro-mechanical relays. They are capable of switching voltages up to 300VDC/250VAC and current up to 2A
-
product
Circuit Module, Riser for ISMB 2U PCIe X16 Riser Card to 2 PCIx8 Expansion Slots , and PCI card
AIMB-RP3P8-12A1E
Support ISG 2U chassis
