Pyroelectric Sensors
Turn absorbed radiant energy into a current or voltage.
See Also: Thermopile Sensors
-
Product
USB Power Sensor, 50 MHz to 24 GHz
U2002H
Power Sensor
Measure average power over the frequency range 50 MHz to 24 GHz and power range -50 dBm to +30 dBm.
-
Product
S2 Unicolor Digital Sensors
ULP-S2 SCC
LED Sensor
The Universal LightProbe S2 Unicolor Digital Sensor is pre-programmed to respond only to a specific color LED, including blue, green, yellow, orange, red, plus white. The Universal LightProbe S2 Unicolor Digital Sensor is designed for the simple ON/OFF test and color check of a single color LED, with a digital output, quickly determining PASS/FAIL status without further processing by Automatic Test Equipment. The Universal LightProbe S2 Unicolor Digital sensor provides the simplest and fastest interface to Automatic Test Equipment (ATE).Operating temperature range: 0oC to 70oCPower consumption: Operates between +5 and 28 volts, at 6mA max.; less than 4.75 volts is not recommendedVoltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsSignal Output Loads: 20 mA max. Non-inductive.Output Pins: 3 gold-plated standard wire-wrap pins (0.025 in. sq.)Sensor Size: 0.560 in. dia x 1.38 in. longOperating Temperature Range: 0hC to 70hCTypical response times: <10mS capture time; <65mS overall response timeFiber-Optic Probes: Can utilize any Universal LightProbe Fiber-Optic Probe
-
Product
10 MHz to 6 GHz LAN Wide Dynamic Range Average and Peak Power Sensor
L2061XA
Power Sensor
The Keysight L2061XA is a fast, accurate and wide dynamic range 10 MHz – 6 GHz LAN peak power sensor.
-
Product
Power Sensor and SNS Noise Source Cables (3 m/10 feet)
11730B
Power Sensor
The Keysight 11730 series power sensor cables are used with the 8480 and E-series power sensors (except the E9320 family of peak and average sensors). These cables are designed to reduce RFI effects on low power readings with an improved shielding design in the cable itself. Cables may be ordered individually or in pairs in any combination desired for single and dual-channel measurements.
-
Product
Balance Thermocouple Power Sensor, DC To 50 GHz
N8487S
Power Sensor
The Keysight N8480S Series Balance Thermocouple Power Sensors are intended to be used as measurement standards for RF power. They are suitable for use in a microcalorimeter-based primary measurement standard and as a secondary or reference measurement standard. The new balance thermocouple power sensors offer a broad frequency range DC up to 18/50 GHz, high maximum input power of +20dBm, fast measurement speed/settling time as well as ease of maintenance.
-
Product
P-Series Wideband Power Sensor, 50 MHz to 40 GHz
N1922A
Power Sensor
Peak, peak-to-average ratio, average power, rise time, fall time, maximum power, minimum power, and statistical data of wideband signals.
-
Product
Wideband Power Sensor, 50 MHz to 40 GHz
N1924A
Power Sensor
The Keysight N1924A peak power sensor provides peak, peak-to-average ratio, average power, rise time, fall time, maximum power, minimum power and statistical data of peak signals.
-
Product
Sensors
Contour Probe
-
Contour tracer in a coordinate measuring machineMeasurement in workpiece coordinatesCapable of scanning in any directionMicro and macro structures can be measuredCalibration of optical measurements
-
Product
Sensors
-
Com-Ten offers a wide range of sensors to suit your different applications. Force and torque sensors of various capacities and sizes, combined to wired and wireless measurement displays, we can offer you a solution for your testing needs.
-
Product
Sensors
-
Diversified Technical Systems, Inc.
DTS offers a full line of high performance data acquisition systems, sensors, accessories and software to meet a wide range of critical test requirements. Let the DTS team of experienced engineers and test professionals help you find the right instrumentation for your application.
-
Product
S2 Spectra USB Sensors
ULP S2 SPECTRA USB
LED Sensor
The ULP S2 Spectra USB Sensor Data Sheet tests a wide range of LED intensities, and any color in the visual spectrum, plus white, providing a linear response with a serial digital output via a PC.
-
Product
Sensors
TA120
-
The TA120 sensor combines the precision of a Class 1 sound level meter, maximum protection of an outdoor kit and full connectivity with open source platforms.
-
Product
Sensor
Hyperion Turbidity
-
Valeport’s Hyperion Turbidity sensor delivers high-performance measurements of turbidity, in a compact & robust package ideal as a standalone sensor, for ROV and AUV integration or used as part of a multi-sensor array and data logger.
-
Product
Wide Dynamic Range Power Sensor, E-Series
E4413A
Power Sensor
E4413A - The E4413A CW diode power sensor measures average power over the frequency range 50 MHz to 26.5 GHz and power range -70 to +20 dBm (90 dB dynamic range).
-
Product
E-Series Average Power Sensor
E9301B
Power Sensor
Measure the average power of all modulation formats Wide dynamic range power measurements from -30 dBm to +44 dBm10 MHz to 6 GHz frequency coverage for Wireless Comms formats Low SWR for reducing mismatch uncertainty Calibration factors, linearity and temperature compensation data stored in EEPROM Compatible with EPM (new N1913A/ 14A, E4418B/ 19B), EPM-P (E4416A/ 17A) and P-series (N1911A/ 12A) power meters
-
Product
Sensors
-
To measure machinery or structural vibration, a transducer is needed to convert the mechanical motion into an equivalent electrical signal. Each sensor has distinct advantages in certain situations and limitations in other, so it is important to select the most suited transducer or sensor for your job. Equally, important is selecting the appropriate parameter of vibration amplitude for measurement. IRD® has a wide range of transducers and accelerometers available to help you obtain accurate, reliable data, whether your concern is vibration monitoring, analysis, or dynamic balancing.
-
Product
Sensors
-
SHIMPO INSTRUMENTS offers a variety of sensors and rotary pulse generators to send various trigger signals to panel tachometers, counters and stroboscopes. When coupled with the appropriate SHIMPO panel meter or stroboscope, our sensors can be used in many different operating environments from laboratory to hazardous Class I -Group C&D and Class II- Group E, F, & G.
-
Product
Amplifier Operating with High Temperature Accelerometers Where Pyroelectric Effects May be Encountered
Trig-Tek™ 203PC-1/2
Amplifier
Operates with high temperature accelerometers where pyroelectric effects may be encountered, with frequency range from 3 Hz to 40,000Hz
-
-
Product
Sensors
WerthZoom®
-
Precise and flexible optical measuring systemWide zoom range (0.7x to 6.8x)Variable working distance (20 – 200 mm 0.8” – 8”)High accuracy with high magnification / Large field of view at lower magnificationHigh accuracy and repeatability due to linear bearings systemEncoders in the drive unit guarantee long term stability and repeatability
-
Product
Vibration Sensor
ENVIROMUX-VSS
-
For registering movement and shocks. Adjustable sensitivity. Connect to RJ45 or digital input sensor ports. Supports CAT5/5e/6 UTP or STP cables. Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Maximum cable length: 1,000 ft (305 m). Regulatory approvals: RoHS.
-
Product
Photocell Sensor
AS6 220V 10A-B
-
Konstar Electric Industrial Co., Ltd
Photocell sensor switch can control the light switch automatically according to the light ray. When the sky become dark, the light will be on, but the day is coming, the light will off at once.It can used on the street lamps, stairs lamps, garden lamps etc.
-
Product
Non-Contact Sensors
IRIX
-
Sciences et Techniques Industrielles de la Lumière
IRIX™ is a family of non-contact sensors based on chromatic confocal technology capable of measuring distances and thicknesses on any material transparent to white light.IRIX™ is capable to measure simultaneously up to five layers of material. The controller can be used in combination with a large family of optical probes with different measurement ranges, mechanical dimensions and metrological specifications to best meet the most diverse application needs.
-
Product
Sensor Node
Smart Parking
-
Libelium Comunicaciones Distribuidas S.L
The main method is magnetic detection: a 3-axis magnetic sensor reads the variations in the Earth's magnetic field. The big mass of metal of a car parked on the slot changes this field and the node will know. The software inside the node implements advanced algorithms to dynamically compensate the temperature variations and also the influence of neighbor cars.
-
Product
Force Sensors
-
TE Connectivity (TE) designs and manufactures force sensors for applications that require high performance or unique packaging, including electro-mechanical flight control, test and measurement and ultra-low cost OEM load cells for medium to high volumes. Based on our proprietary piezoresistive silicon strain gage (Microfused) technology, our sensors combine durability and long-term stability in extremely low cost packages.
-
Product
Precipitation Sensors
-
Campbell Scientific offers several types of sensors to measure precipitation: tipping bucket rain gages, siphoning tipping bucket rain gages, heated rain gages, and snowfall adapters. Users often select their precipitation sensors based on the type of precipitation to be measured (rain or snow), as well as the needed orifice diameter, measurement range, and accuracy level.
-
Product
Pressure Sensors
-
The output voltage changes with the absolute pressure applied to the pressure port. The gain, offset and thermal drift of the pressure sensor is digitally compensated to minimise errors and to create a single-ended, amplified output in the 0 to 5 Volt range.
-
-
Product
Proximity sensors
-
Voltage 0...250V DC, 230 V AC Cable length 0.3, 2.5, 5, 7.5, 0.2...10 m Plug connection M8, M12 / female thread M5 Electrical Via reed contact Contactless PNP, NPN Pneumatic.
-
Product
Web Sensor
P8510
-
Thermometer Web Sensor P8510 or Web Sensor P8511 and Web Sensor P8541 are used tomeasure temperature or relative humidity. Temperature can be displayed in C or F. Relativehumidity have unit %RH. Communication with the device is realized via Ethernet network.
