Pyroelectric Sensors
Turn absorbed radiant energy into a current or voltage.
See Also: Thermopile Sensors
-
product
E-Series Average Power Sensor
E9301H
Measure the average power of all modulation formats Wide dynamic range power measurements from -50 dBm to +30 dBm10 MHz to 6 GHz frequency coverage for Wireless Comms formatsLow SWR for reducing mismatch uncertainty Calibration factors, linearity and temperature compensation data stored in EEPROM Compatible with EPM (new N1913A/ 14A, E4418B/ 19B), EPM-P (E4416A/ 17A) and P-series (N1911A/ 12A) power meters
-
product
Sensor Boards
SensorXplorer™
Each sensor board can be used together with the SensorXplorer board.The SensorXplorer boards acts as a USB to I2C interface between Vishay's freely available software modules and the sensor boards. The sensor boards also have test pins for the I2C interface, allowing you to connect them to your own platform.
-
product
Air Temperature and Relative Humidity Sensors
Air temperature and relative humidity probes typically consist of two separate sensors packaged in the same housing. Often relative humidity is measured with a capacitive RH sensor, while air temperature is measured by a PRT.
-
product
3U cPCI Sensor Interface Unit
SIU31
NAI's SIU31 is a highly configurable rugged COTS system or subsystem ideally suited for military, industrial, and commercial applications that require high-density I/O, communications, Ethernet switching, and processing. The SIU31 uses one NAI field-proven, 3U cPCI board to deliver off-the-shelf, SWaP-optimized COTS solutions that "Accelerate Your-Time-to-Mission."
-
-
product
Safety Proximity Sensors
Leuze electronic GmbH + Co. KG
With their encapsulated and contactless design, safety proximity sensors are insensitive to contamination and humidity. They operate free from wear and also have a long life expectancy, even with frequent operating cycles. They are also used wherever it is difficult to precisely guide the moveable protective device. All devices feature a high-strength plastic housing. Furthermore, the devices with RFID transponder provide maximum protection against tampering.
-
product
Gas Flow Sensors
ESRF-HF Transmitter
The ESRF-HF is a family of mass flow transmitters which enable fast and accurate measurements of gas flow over a wide dynamic range. Each transmitter integrates a MEMS flow sensor and readout electronics inside a housing with very small form factor made from stainless steel. The duty pressure of the flow transmitter is 11bar. All measurement data are fully calibrated, and temperature compensated on board, leading to a reduced temperature coefficient and high measurement accuracy.
-
product
Hall Sensor Board with I2C Interface
055-013
Version: +5V/5A +3,3V/5A +12V/5A -12V/5A The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
product
Slim Body Analog Fiber Sensor
FX-11A
Panasonic Industrial Devices Sales Company of America
Panasonic's Slim Body Analog Fiber Sensor FX-11A is a slim body analog fiber amplifier that allows for 1-5Vdc output when using Fiber optic sensing solutions.
-
product
Gyro Sensors For General-Purpose(2)
Panasonic Industrial Devices Sales Company of America
Gyro Sensors For General-Purpose(2)
-
product
*OEM Energy Sensors
The OEM “standard” sensors are actually families of existing OEM sensors with typical specifications shown. They can be tailored as needed to fit your specific requirements. In addition to the products described, Ophir has developed hundreds of other OEM solutions. Simply fill out the Sensor Customization form so we can provide just the right solution for your needs.
-
product
Infrared Array Sensor
Grid-EYE Evaluation Kit
Panasonic Automotive & Industrial Systems Europe GmbH
Panasonic Automotive & Industrial Systems has launched this evaluation kit for its Grid-Eye infrared array sensor, which integrates a ”nanopower” Bluetooth Smart module and a microcontroller. The kit is intended for prototyping the Grid-EYE sensor which is a 64 pixel IR camera in a surface mount package measuring 11.6mm x 8mm x 4.3mm, which integrates the MEMS sensor, lens and I2C interface. The integrated Bluetooth module in the evaluation kit, the PAN1740, draws 4.9mA in transmit or receive operating modes, which means it can be powered by coin cell batteries. The IR sensor has 64 thermopile elements in an 8×8 grid format that detect absolute surface temperature without any contact.
-
product
Differential Magnetoresistive Sensors
ChenYang Technologies GmbH & Co. KG
*Sensing over wide rotation speed range*Robust metallic housing*Signal amplitude is speed independent*Biasing magnet built-in*Best suited for harsh environments
-
product
Hall Sensor Board with I2C Interface
046-323
Version: +5V/60A +3,3V/15A +12V/15A -12V/15A The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
product
Sensors
Chromatic Focus Probe
Measurement of highly reflective, absorbent and transparent materialsMeasuring results are independent of the surface propertiesEspecially suitable for fast and precise measurements on reflective surfaces, lenses, prisms and other optical devicesFlexible probe configurations for highly customized applications
-
product
Reaction Torque Sensor - Shafts
Futek Advanced Sensor Technology, Inc.
Shaft to Shaft Reaction Torque Sensor offers a unique solution for low capacity torque auditing applications.
-
product
Stainless Steel Shims and Sensor Brackets
PRÜFTECHNIK Condition Monitoring GmbH
Sensor mounting brackets and stainless steel shims for vertical alignment and soft foot correction are an integral part of a precision alignment solution. They contribute to the quality of the measurement and the resulting asset reliability. PRUFTECHNIK offers universal or chain-type brackets as well as stainless steel shims for trouble-free machine corrections. Brackets and stainless shim sets are alignment accessories that improve the results and experience for unusual or challenging situations, including soft foot. Quality stainless steel shim sets improve alignment adjustment results and make challenging alignment situations, including soft foot faster and easier.
-
product
CIELab Color Sensor
PR0128
The CIELab Color Sensor PR0128 is a color detection system with integrated high power light source, for determining the surface color. It is characterized by the identification of the smallest color nuances and the highest long-term stability. Here, up to 63 completely different products in different colors can be independently controlled and tested without changing parameters or gain levels.
-
product
Through Hole Type AC Current Sensor
CTF-50B
MULTI MEASURING INSTRUMENTS Co., Ltd.
*For AC current and power measurements.*Suitable for current measurements of feeder cable.*Measuring range:AC 0.1A～50A.
-
product
Strain Sensors
Columbia Research Laboratories
Columbia's foil strain sensors monitor the fatigue loading experienced by tactical aircraft under various conditions of speed, weight and missions configuration. Critical undercarriage structures and control surfaces may be monitored for fatigue damage induced by high-G maneuvers and high stress landings. These sensors are self-temperatures compensating, environmental resistant, have a high output, two active arms and are easily installed. Developed for the demanding requirements associated with tactical military aircraft, they are equally useful performing many of the more common strain measurements encountered in the material testing laboratory. Columbia's foil strain sensors are considered the standard for the industry.
-
product
Sensors
A speed and angle sensor using a black/white tape which is glued on a rotating part. The reflection is converted into a TTL signal, bandwidth 100 kHz. The sensor consists of a tiny electronics part and a 5 m fiber optic cable terminated with a M6 screw. Thus areas where space is very limited still can be reached conveniently.
-
-
product
Inductive Proximity Sensors (Square)
SP2
Easy installation, high-speed pulse generator, high-speed rotation control, and more. A wealth of models ideal for limit control, counting control, and other applications. Sensing distance from 1~2/2 ~ 6/ 5~ 12/10~15mm. Housing by PBT with strong structure and acid resisting available.
-
product
Laser Power Sensors
Make accurate laser power measurements, from the deep UV to the infrared, with these calibrated, traceable sensors.
-
product
Sensors
Our technologies enable measurement capabilities such as pressure, temperature, position, vibration, photonics, force, and humidity.TE Connectivity offers an unmatched portfolio of intelligent and efficient sensors across patient monitoring and treatment and industrial automation applications. Browse from our portfolio to find the suitable sensor to create a safer, more productive, and reliable future together.
-
product
Temperature Sensors
Units with integrated or separate evaluation electronics, Modular concept for a large variety of applications, High process safety due to self-monitoring, Variety of process connections available, High shock and vibration resistance
-
product
Digital Meteorological Sensor
ZET 7023
The ZET 7023 weather sensor is a measuring unit with two in-built sensors one of which is responsible for measuring relative humidity and temperature, and the other one, for atmospheric pressure measuring.
-
product
Displacement Sensor Models Products
LVDT
Linear Variable Displacement Transformer (LVDT) sensors from Stellar Technology are used worldwide in the monitoring and gauging of pavement studies, mining equipment, oil & well drilling equipment, resistance weld stroke, valve position, and assembly processes. Take a look at all of our LVDT options below to find the displacement sensor that meets your application needs.
-
product
Citroen Oxygen Sensor
KS60113 - Citroen
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
-
product
Low Light Sensors
The ever-evolving technologies push the lower limit of measuring the photon energy. Look no further than Newport to find a solution for low light sensing applications. Please see our Low Light Sensor Guide for additional information.
