Voltage Testers
See Also: Proving Units, Power Testers, Voltage Detectors
-
Product
LAN Tester
TVR10/10/100
-
Triplett Test Equipment & Tools
TVR10/100/1000 LAN Tester is comprised of a "Main unit" and a "Remote Probe". The Main unit performs the bulk of the tests, such as determining the LAN device type (is it a hub/switch or PC?), the LAN speed and duplex (10, 100, 1000 MB/s, half or full duplex) and whether PoE (Power over Ethernet) is present without the need of the Remote Probe. The Remote Probe adds the ability to trace cable locations (by audibly tracing tones placed on the cable by the Main Unit) and to test the wiring of the cable (by decoding and displaying wiring information placed on the cable by the Main Unit).
-
Product
LED Testers
-
PeakTech Prüf- und Messtechnik GmbH
An extremely practical component tester for LEDs and other components. The device outputs an automatically raised output voltage between 0 to 300 V DC, which adapts to the connected load so that the sensitive components are not destroyed. Particularly suitable for the service and repair workshop.
-
Product
Pull Off Adhesion Tester
106
-
Applications for the Elcometer 106 Adhesion Test include paint or plasma spray on bridge decking, coatings on steel, aluminium, concrete etc.Supplied in a carry case - ideal for site testsHand operated - no need for a power supplyIncludes a cutter for EN13144 and ISO 4624 tests
-
Product
Waterproof Ozone Tester
ORPTestr 10
-
Large Display Screen - dual display LCD for enhanced readability, provides comprehensive meter information
-
Product
Battery Cell Tester
-
This Centre zero instruments help to read the voltage irrespective of polarity.
-
Product
Concrete Strength Testers
-
This category of products comprises the range of instruments utilized to evaluate construction material strength. The range of instruments is typically considered to be two parts. The first are non-destructive field tests of compressive strength. The second are tensile field tester systems to either determine the tensile strength of an overlay or bond material, or tensile strength of anchors embedded in the concrete. The first group is pure Non-Destructive Testing where the strength of the material is determined by correlation to another parameter more easily available and readily apparent. This is typically the hardness of the concrete or the resistance to penetration by either a pin or probe. The Windsor Probe, Windsor Pin and our line of Rebound Hammers all fall within this category. These are widely used standard tests and as such have seen use throughout the world.
-
Product
Socket Tester c/w Buzzer
DL1092
-
Clear visual and audible indication RCD test of 30 mA RCD (max time 300 ms) Touch voltage to check for extraneous voltage on earth Compact, durable design in compliance with BS EN 61010
-
Product
Mechanical Tester
UMT TriboLab
-
Bruker’s Universal Mechanical Tester (UMT) platform has been the most versatile and widely used tribometer on the market since the first model debuted in 2000. Now, newly designed from the ground up, the UMT TriboLab™ builds on that legacy of versatility with a unique modular concept that harnesses more functionality than ever before—all without any compromise in performance.
-
Product
5G Radio Communication Tester
CMX500
-
The R&S CMX500 radio communication tester is the future-proof solution for 5G NR testing, featuring an intuitive and flexible web-based user interface, the R&S CMsquares. Supporting manual interactive operation as well as automatically sequence-controlled test protocols makes the R&S CMsquares an advantageous software solution, with unique modules for all signaling use cases. These range from R&D design stages up to end-to-end application testing, production and conformance tests. The introduction of a one-platform strategy for all 5G NR test equipment enables a unified test environment for signaling and non-signaling testing through all stages of 5G device production.
-
Product
ICI Mace Snag Tester
UI-TX07
-
ICI Mace Snag Tester – ICI Mace Tester is used to test fabric snagging resistance ability. It is suitable for woven and hnitted fabric made from textured or untextured filament yarns and etc. ICI Mace Snag Test Method includes ASTM D3939, JIS L1058, GB/T 11047 and etc.
-
Product
PoE Voltage Monitor Detect & Verify
PE-400
-
PE-400 is specific to test and verify PSE or Ethernet outlet either a standard/active PoE or a NON-standard/passive PoE to avoid damaging Non-PoE device as well as monitor and display available Voltage simultaneously. It built-in PoE interface controller to trigger on 802.3 af, at and bt switch and verify standard PoE type either 802.3 af or 802.3 at, and power source either End or Mid or both, and power polarity as well as display voltage values. The operational voltage which should be measured when installing a new PoE system or when you troubleshooting an existing system.
-
Product
Handheld Return Loss Tester
JW3308
-
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
JW3308 handheld return loss tester is used to measure the return loss in the field fiber optic linking, in order to adjust the quality of the optic fiber end-face, and to make sure the fiber optic communication is in good condition. This 3308 handheld return loss tester can realize measurement of Return Loss, Insertion Loss, Output power, and also can be used as the laser source. Moreover, it has the data storage function of 500 measurement items.
-
Product
Distribution Transformer Tester
ADOC-3
-
The ADOC-3 is an equipment that has been designed to test distribution network transformers from 5 kVA to 3MVA.
-
Product
PXI 5 Ch. Differential Hi Voltage Attenuator
41-661-001
-
High voltage attenuators designed to reduce the high output voltages commonly generated by some types of sensors. This is in order to produce manageable signal levels that can be acquired by typical data acquisition devices in a PXI system.
-
Product
Electrical Tester Grid Field
-
TCI can furnish grid spring probes for most Bare Board Electrical Testers in production at most Printed Circuit Board Manufactures. Look for your model of Bare Board Tester in the following list and call TCI for current price quotation.
-
Product
High Voltage Breakdown Test Sets
HT-Series
-
Dielectric Voltage Withstand Test or High Potential Test (HIPOT test) is a 100% production line test to verify the quality & electrical safety characteristics of products.
-
Product
Franklin Tester
Model 717
-
The Model 717 Franklin Tester provides a means of testing single strips or punchings of flat rolled electrical steel, for surface insulation resistance under predetermined conditions of voltage and pressure.
-
Product
COTS VME Board Tester
-
*Developed for support of Virginia Class Submarine at the COATS Integration Facility.*Provides Stimulus and Measurement Subsystem (SMS) to control, monitor, and evaluate VME assets used in the Non-Propulsion Electronic System (NPES) of the submarine.*Provides Native Environment Subsystem (NES) that simulates the operational configuration of typical NPES installations, and permits the test and evaluation of several types of VME assets.
-
Product
PHP Tester
nette
-
Nette is a set of PHP 7 standalone components that make up the framework, rated as the 3rd most popular in the world. Nette puts extra emphasis productivity, clean code, and security.
-
Product
Audio Impedance Testers
1107 IM
-
Standard Electric Works Co., Ltd
● Large LCD : 68 × 34mm(2.677" × 1.338").● True measurement of speaker systems actural impedance at 1kHz.● Three test ranges allow testing of home theater and commercial sound systems.● Measures transformer impedances.● Battery operation.● Low battery indication.● Data hold function.● 0Ω adjustment.
-
Product
Din Abrasion Resistance Tester
SG-P01D
-
This tester is used to determine the abrasion characters of elastomers, rubber, soft synthetics, leather. etc or is with characters of high efficiency, good reproducibility and easy operation.
-
Product
Lightning Impulse Simulation Tester
KT-6030iG
-
Most of all electric systems and equipments are weak against the lightings(direct, inductive lightning). In fact, those electric equipments are broken mainly by lightning.This Lightning Impulse Simulation Tester is certificated to IEC 61000-4-5, and generates the similar impulse with huge rush currents and tests the safety of the power systems and equipments.
-
Product
Panel-mounted Voltage Power Amplifier
PAV120Bi
-
PAV120Bi is specially designed for R&D of power system simulation. It is adapt to various capacitive and inductive load. It is with 6 channels voltage outputs, each channel with 120V/60VA maximum output.
-
Product
High Voltage SMU
-
Source and Measurement Units (SMUs) are devices that generate voltages or currents and can measure them simultaneously using the integrated measuring units (VMU, CMU).High-voltage SMUs work as a regulated voltage source and are able to generate very high output voltages.
-
Product
Shore A Type Hardness Tester Rubber Hardness Tester
HS-A
-
Shenzhen Chuangxin Instruments Co., Ltd.
HS-A is a digital Shore A type hardness tester. It is suitable for plastic (such as film, medical appliance, etc.), synthetic rubber(such as seals, tires, rubber roller, rubber hose/belt, wire and cable, shock absorber, etc.) and other related chemical products.
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-213-HI
-
The 40-230-213-HI (PXI) and 42-230-213-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 2.5Ω and 239Ω with 1Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Barcol Impressor Hardness Tester
3101
-
The Elcometer 3101 Barcol Impressor Hardness Tester is easy to use and ideal for measuring the hardness of soft metals, plastics, glass fibre and leather.
-
Product
Smoothness Tester
DRK105
-
Shandong Drick Instruments Co., Ltd.
DRK105 Smoothness Meter is designed according to Bekk method to measure paper and cardboard’s smoothness.
-
Product
IEC60065 Socket Torque Balance Tester Torsion Tester
-
Shenzhen Chuangxin Instruments Co., Ltd.
*Plug and Socket Torque Tester/Device is for compliance is checked by engaging the device, as during intended use, with the socket-outlet of a test apparatus. *Plug Torque Tester/Equipment is a device provided with pins intended to be introduced into fixed socket-outlets shall not impose undue strain on these socket-outlets.The balancing arm of the test apparatus pivots about a horizontal axis through the centre lines of the contact tubes of the socket-outlet at a distance of 8 mm behind the engagement face of the socket-outlet.*With the machine not in engagement, the balancing arm is in equilibrium, the engagement face of the socket-outlet being in the vertical position.After the device has been engaged, the torque to be applied to the socket-outlet to maintain its engagement face in the vertical plane is determined by the position o a weight on the balancing arm.
-
Product
4 Moving Probe Tester
L Series E4L6151
-
This is the latest EMMA series affordable model that offers low damage, high-speed and high-accuracy test. Max. Test Area24 x 20" (610x510mm). Number of Probes2 Front, 2 Rear. Min. Pad Pitch *10.007087" (180µm). Min. Pad Size *20.00314" (80µm).
