Exposure Meters
Measure time in a given environment
-
Product
Outdoor Exposure Tester
OET
-
A comprehensive analysis of PV modules includes many different parameters. Determining the normal module operating temperature (NMOT), incidence angle effects and comparing soiling effects on different modules up to the initial degradation of PV modules are all parameters that can be analyzed with our outdoor exposure tester. The tester comes with up to twelve electronic loads installed in a 19" rack. The loads have two main functions: maximum power point tracking (MPPT) and IV curve tracing. For the advanced analysis, it is possible to change between these two modes within one test. In the normal operation mode, the electronic load keeps the module under MPP and each predefined interval an IV curve is traced. The entire tester comes with all necessary sensors such as temperature sensor, which can be attached to the module to determine the NMOT temperature like defined in IEC 61215 (MQT 05) and IEC 61853-2. The irradiation sensor is also included. In combination with our tracking system P2, it is also possible to determine incident angle effects of the PV module. It is also possible to connect other irradiation sensors for diffuse and direct irradiation, which helps to understand the behavior of the module in different irradiation conditions. An optional albedo meter is a powerful tool for the analysis of bifacial modules. The entire graphical user interface is web based and offers the possibility to access the system from the all computers in the network.
-
Product
VDI Erickson PM5B MM–Wave Power Meter with W-Band Sensor, Optional Tapers to 1.5 THz
N1913PM5B
Power Meter
N1913PM5B is a Virginia Diodes, Inc./Erickson PM5B calorimetric mm-wave power meter, with a W-Band sensor for power measurement over a frequency range of 75-110 GHz.
-
Product
Vibration Exposure Timers
-
EU Directives and the UK Regulations specify specific daily exposure limits, which can be translated into the HSE's Exposure Points. Points are determined quantifying the Vibration Level of tools and the Time that operators are exposed to the vibration, named Exposure Time.
-
-
Product
*High Power Measurement From Short Exposure
-
Ophir has a number of ways to measure high laser powers up to 12kW without heavy water cooled equipment. Most of today’s lasers can be set to emit for a short, precisely controlled period of time. If a short exposure to the laser of 0.3 – 10s is sufficient to measure the power then there are compact, uncooled sensors available for this purpose.
-
Product
Low Outgassing Cables Suitable For Thermal Vacuum Chamber Exposure
-
Low Outgassing Cables Suitable for Thermal Vacuum Chamber Exposure.
-
Product
Exposure Systems
Model 2012AF & 2012SM
-
The Model 2012AF Flood Exposure System provides a cost-effective method for automated flood exposure. Designed to accommodate wafers from 8” to 300mm, the tool features automated FOUP loading. Mask and substrate changeover can be accomplished quickly and easily adding to both versatility and high-volume throughput of this production tool.The Model 2012SM Automated Edge-bead Exposure System provides a cost-effective method for edge-bead removal using standard shadow mask technology. Designed to accommodate wafers from 8” to 300mm, the tool features automated FOUP loading. Mask and substrate changeover can be accomplished quickly and easily adding to both versatility and high-volume throughput of this production tool.
-
Product
Exposure Systems
Model 2000AF & 2000SM
-
The OAI Model 2000 Exposure Systems may be configured as either an edge-bead exposure system (2000SM) or a flood exposure system (2000AF); both configurations are based on OAI’s proven, time-tested platform.
-
Product
Analog Optical Power Meter - MATRIQ
1500 Series
Power Meter
The Power 1500 Series analog power meter brings cost-effective test and measurement. The Power 1500 provides logarithmic analog output as well as a digital optical power meter for applications that require real-time feedback.
-
Product
Exposure Level Tester
ELT-400
-
*Wide frequency range (1 Hz - 400 kHz)*Standard-compliant measurement*Acceptance measurements compliant with CE standard IEC/EN 62233 and Generic Standard IEC 62311*Limit value traces conforming to ICNIRP 1998, 2010 and EMF Directive 2013/35/EU*Real time measurement with RMS and peak detectors*External FFT signal analysis for determining the frequency components via three channel analog output (one channel for each spatial axis) e.g. with the aid of a digital oscilloscope.
-
Product
Small InGaAs Camera For Short Exposures
Bobcat Gated Series
-
The Bobcat 320 Gated series is based on an in-house developed, temperature stabilised InGaAs detector with a 320 x 256 pixel resolution. The Bobcat 320 Gated cameras are able to provide maximum frame rates up to 400 Hz. The exposure time of the sensor is configurable from 100 ns up to 1 ms in steps of 100 ns, or from 1 ms to 40 ms.
-
Product
Human Exposure Measurements to Luminaries
-
Through different ways of coupling between luminaries and humans, a level of exposure of a person to electromagnetic fields can be derived. One part of the exposure is based on capacitive coupling between lighting equipment and person. This creates induced internal electric field that must be evaluated using an EMI receiver and a Van Der Hoofden test head.
-
Product
Wavelength Meter
-
HighFinesse/Ångstrom offers sensitive and compact wavelength meters with a large spectral range for high speed measurement of lasers. The optical unit consists of temperature-controlled Fizeau-based interferometers that are read out by photodiode arrays. The high absolute accuracy is achieved by use of solid state, non-moving optics.
-
Product
Light Meter
-
Shenzhen UYIGAO Electronic Technology Co., Ltd
Digital Luxmeter Lux light meter for photography Photometer Mini spectrometer spectrophotometer Luminometer
-
Product
Voltage Meter
MN8IP
-
The mezzanine module (mezzanine) MN8IP is designed to measure instantaneous voltage values over eight differential channels isolated from each other and control circuits.
-
Product
Vibration Meters
-
GAOTek offers a wide and dynamic selection of high-quality, affordable and accurate Vibration Meters. A vibration meter is used in inspections, manufacturing, and production to measure vibration and oscillations. The main function of a vibration meter is to measure displacement, velocity and acceleration of a vibrating body.
-
Product
Conductivity Meters
-
Conductivity meter measures the amount of electric current or conductivity in solution.A conductivity meter measures the health status of the natural water body.It is very useful in the field of water.
-
-
Product
Clamp Meters
-
Clamp meter is a rugged high end AC clamp meter. With a UL listed safety rating of CAT IV 600V / CAT III 1000V, this clamp meter is built to get the tough jobs done.
-
-
Product
Clamp Meters
-
oltage DC 600V with basic accuracy ±(0.5%+5d)Voltage AC 600V with basic accuracy ±(0.8%+5d)Current AC 400V with basic accuracy ±(2.50%+6d)Slimline Electric Clamp Meter Resistance 20M ohms with basic accuracy ±(1.0%+4d)Continuity buzzer sound at 300 ohmsDiode test current 0.3mA; Open circuit voltage 1.5VAccessories: test leads, carrying case, 2(AAA) 1.5V batteriesSize:8-1/16"L x 2-3/4"W x 1-1/2"HSlimline Electric Clamp Meter Weight: 7oz.2000 LCD display countsDecimal Point ReadingsDisplay with backlightData holdMax holdAuto power offLow battery indication
-
Product
Vibration Meters
-
A vibration meter is used in manufacturing for machine condition monitoring, product testing and quality assurance. Many machine maintenance technicians use vibration meter devices in tandem with sound level meters to analyze frequency. A vibration meter also can be used in civil engineering to measure the vibration of structures such as buildings, roads and bridges. In addition, specialized vibration meter devices can be used to measure the vibration of the human body. Any vibration meter will measure one or more of the following parameters: vibration acceleration, vibration velocity (speed) and / or vibration displacement.A vibration meter is typically a portable device with a memory for storing measurements. Most vibration meter models feature a built-in data logger for collecting and recording vibration measurement data over time. In this way, vibration measurement data can be acquired with great precision.
-
Product
Dynamic Meter
Dynamic
-
After nearly three years of research and development ZLS has introduced a meter for marine applications. The ZLS Dynamic Meter is a completely new meter designed to eliminate inherent cross-coupling errors, frequent damper adjustments, and vibration sensitivity problems associated with beam-type gravity meters.
-
Product
Field Meter
AP 301 FULL HD
-
The AP301 FULL-HD is a field meter with total coverage of terrestrial TV bands, cable TV (CATV), 1st IF satellite and, if the relative option is inserted, the return channel 5-65 MHz.
-
Product
Bench Meters
Digital Multimeters
-
UNI-T multimeter has been selling well for more than 30 years and has become a leading brand globally hand-held multimeter. Multimeter is a must-have tool for many engineering benches, UNI-T bench type DMM continues to create long-term value for customers, whether you are engaged in maintenance services or design, UNI-T guarantee you to find a right one for the extra edge to come out with products or services that is better than your competitors.
-
Product
Edgewise Meters
-
Hoyt Electrical Instrument Works Inc.
Hoyt edgewise meters have high visibility scales and straight forward design that make them especially suited to small, limited space, rack mounted power supplies and allied equipment. Supplied bezel and mounting hardware enable quick, trouble-free installation. Choose from the 685-1, 685-2, or the 685-3 depending on whether you need a single meter or multiple edgewise meters.
-
Product
Deceleration Meter
VZM 300 | VP 185016
-
Maschinenbau Haldenwang GmbH & Co. KG.
The VZM 300 braking deceleration measuring device is used for mobile brake testing - especially - of special vehicles and corresponds to the national type approval by the PTB (Physikalisch Technische Bundesanstalt). The VZM 300 consists of a printer housing including a digital display and keyboard.
-
Product
Sound Meters
-
Sper Scientific sound meters include all the features and functions needed for basic noise level surveys or to meet the requirements for OSHA compliance, community noise ordinances or machine noise evaluation. These sound meters are used by: Industrial Hygienists, Sound Engineers, Construction Engineers, Municipal Code Enforcement officials, Industrial Quality Control, Environmental Scientists, and many more.
-
Product
Woltman Meter
-
Key structure is made up of rotary carried helical blades which goes around as the same direction of water flow.
-
Product
Charge Meter
NK-1001A/NK-1002A
-
Probe-type charge meter that can easily measure the amount of discharge charge that causes static electricity destruction in the manufacturing, inspection, and assembly processes of electronic devices.Many ESD phenomena that impair electronic devices are represented by the CDM ( Device Charging Model). The CDM is a model that represents a phenomenon in which a high peak current flows at high speed when the device itself is charged and its external electrode is grounded. The coulomb meter measures the amount of discharge charge, which is the integral value of the current, with high accuracy.
