PCI Backplanes
-
Product
PCI Card
EXC-1394PCI
-
The EXC-1394PCI card for the PCI bus is an intelligent test and simulation card for interfacing to an IEEE-1394 data bus. It implements a 1394b PHY layer, operating at 100, 200, or 400 Mbps.
-
Product
PCI High Density Resistor Card 18-Channel, 8 Bit, 0 To 255 Ohm
50-295A-121-18/8
Programmable Resistor Module
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI Card with input channels
PCI_LVDS_8R
-
The PCI_LVDS_8R has 8 channels of LVDS input. The channels are grouped two per Filter Xilinx. The input data is filtered, then written to the Input FIFO. There is one Input FIFO per LVDS channel. 1K x 32. One Latch Xilinx handles 4 LVDS channels. The data is read from the Input FIFO by the Latch Xilinx and either written to the SDRAM or the Output FIFO.
-
Product
PMC-to-PCI Express Adapter
4749
-
Our PMC-to-PCI Express Adapter 1X (64-Bit) (4749) permits the use of a single-wide PMC module in a 1X PCIe slot. The product features a PEX8114 bridge running in transparent mode.
-
Product
Dual-Site Single-Slot 6U Compact PCI (cPCI) PMC Adapter/Carrier
6332
-
Our Dual-Site Single-Slot 6U Compact PCI (cPCI) PMC Adapter/Carrier 32-Bit/66 MHz (6332) adapts two single-wide PMCs to a cPCI slot. At the heart of the carrier is a 6150 PCI-to-PCI bridge that connects the carrier's internal PCI bus to the cPCI backplane.
-
Product
6U Compact PCI Multiport Serial Card
CP69002
-
LinkedHope Intelligent Technologies Co.,Ltd.
CP69002 is designed as 6U Compact PCI Multiport Serial Card. The eight serial ports are in depended and magnetic isolated. The transform mode can be configured as RS232, RS422 and RS485 through the jumpers. The upstream interface is 32 bit 33MHz PCI bus.
-
Product
PCI-6123, 8 AI (16-Bit, 500 kS/s/ch), 8 DIO, PCI Multifunction I/O DeviceMultifunction I/O Device
779409-01
Multifunction I/O
8 AI (16-Bit, 500 kS/s/ch), 8 DIO, PCI Multifunction I/O Device - The PCI‑6123 is a simultaneous-sampling, multifunction DAQ device. It offers analog input, digital I/O, two 24‑bit counters, and digital triggering. The PCI‑6123 is ideal for a variety of applications, such as IF digitization; transient recording; ISDN, ADSL, and POTS manufacturing test in the telecom industry; ultrasound and sonar testing; and high-energy physics. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements. The PCI‑6123 dimensions require chassis slots that can accommodate full-length PCI modules.
-
Product
PCI High Density Pecision Resistor Card
50-298-131
Programmable Resistor Module
The 50-298-131 is a high density programmable resistor card with 4 channels which can be set between 3Ω and 13.6kΩ with 0.25Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
PCI High Density Pecision Resistor Card, 4-Channel, 2.5Ω To 1.81kΩ
50-298-122
Programmable Resistor Module
The 50-298-122 is a high density programmable resistor card with 4 channels which can be set between 2.5Ω and 1.81kΩ with 0.5Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI Data Acquisition Boards
AD12-100DMA Series - Dual 12-bit A/D, 25 MS/s
-
Model AD12-100DMA is similar to the ADDA12-100DMA, but does not have D/A converters.
-
Product
PCI-4065, 6½-Digit, ±300 V, PCI Digital Multimeter Device
779770-01
Digital Multimeter
The PCI‑4065 makes AC/DC voltage, AC/DC current, and 2‑ or 4‑wire resistance measurements, as well as diode tests. It is ideally suited for OEMs, educational laboratories, or other cost-conscious test and measurement applications.
-
Product
PCI 2 Amp Multiplexer, Single 16-Channel, 2-Pole
50-635A-102
Multiplexer Module
The 50-635A-102 is a single 16-channel, 2-pole MUX and is part of a range of PCI Multiplexer cards available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PCI Expansion Card
4624-3
-
VECTOR Electronics and Technology, Inc.
120 contacts (60 each side) on 0.050" centers. Overall GND plane, Pad-Per-Hole, Peripheral Buses. Isolated pads around each hole. 32-bit ISA format. Universal tab fits both 3.3V and 5V tab notch patterns. Mounting bracket included.Peripheral buses for voltage and ground distribution.I/O mounting area for D-sub and ribbon cable connectors.
-
Product
PCI, IEEE 488 GPIB Instrument Control Device for Linux
778686-01
GPIB Controller
The PCI‑GPIB is a plug‑and‑play IEEE 488 interface for PCs and workstations with PCI expansion slots. The PCI‑GPIB can sustain data transfer rates of more than 1.5 MB/s using the IEEE 488.1 three‑wire interlocked handshake. It also implements the high-speed IEEE 488.1 noninterlocked handshake (HS488) for benchmarked data transfers at more than 7.7 MB/s. The onboard bus master DMA controller means that there are no microprocessor interruptions in data transfer.
-
Product
Single Rear Slot Universal Low-Profile PCI to Compact Flash Adapter
P312
-
To cater for the latest generation of Low Profile PCs that can only use Low Profile PCI add-in boards, Elan has created the P312. This model, from the P-Series range, features a Compact Flash Type II ejector and a circuit board that conforms to the MD1 profile specification. It will allow you to use any Compact Flash card such as IBM MicroDrives, Bluetooth cards, WLAN 802.11b cards, data acquisition cards, pager cards, GPS cards etc.
-
Product
PCI 2 Amp Multiplexer, Dual 8-Channel, 4-Pole
50-635A-007
Multiplexer Module
The 50-635A-007 is a dual 8-channel, 4-pole MUX and is part of a range of PCI Multiplexer cards available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PCI Express Card With Eight Isolated Inputs, Eight Relay Outputs, And Change Of State Detection
PCIe-IIRO-8
-
This product is a x1 lane PCIe isolated digital input and relay output board with Change of State (COS) detection capabilities.
-
Product
PCI-6284 , 32 AI (18-Bit, 625 kS/s), 48 DIO PCI Multifunction I/O Device
779110-01
Multifunction I/O
32 AI (18-Bit, 625 kS/s), 48 DIO PCI Multifunction I/O Device - The PCI‑6284 offers analog input, correlated digital I/O, two 32‑bit counters/timers, and analog and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Squid Carrier Board™ Family PCI Express Gen 3 Carrier Board for 4 M.2 PCIe SSD Modules
SKU-086-B4
-
B-series PCI Express Gen3 Carrier board was designed as a cost-effective storage solution for the systems that are using a motherboard with PCI Express bifurcation support. Such motherboards can be configured in the BIOS to split x16 PCI interface to four PCI Express interfaces by utilizing the following PCIe lanes:- x4 PCI Express interface 1: lanes 0,1,2,3 from x16 PCIe interface;- x4 PCI Express interface 2: lanes 4,5,6,7 from x16 PCIe interface;- x4 PCI Express interface 3: lanes 8,9,10,11 from x16 PCIe interface;- x4 PCI Express interface 4: lanes 12,13, 14, 15, from x16 PCIe interface;
-
Product
5 Port PCI Express
PEX 8505
-
The ExpressLane™ PEX 8505 5-lane, 5-port switch product offers PCI Express switching capability conforming to the PCI Express Specification r1.1. This device with an equal number of lanes and ports can be used in a wide variety of applications including control planes in the communications and networking markets, embedded systems, notebook and docking stations, set-top boxes, digital video recorders and multi-function printers.
-
Product
PCI-6143, 8 AI (16-Bit, 250 kS/s/ch), 8 DIO, PCI Multifunction I/O Device
778913-01
Multifunction I/O
The PCI‑6143 is a simultaneous-sampling, multifunction DAQ device. It offers analog input, digital I/O, two 24‑bit counters, and digital triggering. The PCI‑6143 is ideal for a variety of applications, such as … high-energy physics, ultrasonic and sonar testing, ballistics and highly transient signals, and multiaxis control. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
PCI - Quad Industry Pack Carrier w/ DSP
PCI-4IPM
-
The PCI-4IPM module provides a high performance flexible I/O scheme, that supports industry standard Industry PacksÔ. For application requiring low cost, high density I/O or unique combinations, the PCI-4IPM is the perfect solution.The Local DSP can be used to simply move data to and from the CPCI bus or provide pre processing functions such as local PID controls, FFT’s, digital filtering, etc. Custom application software can be downloaded to the DSP via thePCI bus. WinNT drivers are standard.
-
Product
Low-Profile 16-CH Isolated DI & 16-CH Isolated DO PCI Card
LPCI-7230
Analog Input Module
ADLINK LPCI-7230 is 32-CH isolated input and/or card. It provides a 2,500 C optical isolation protection. Two wide input range of the LPCI-7230 makes it easy to sense the status of external devices. The non-polarity characteristic is suitable for a wide variety of industry applications. The LPCI-7230 devices also feature a wide output range from 5 to 35 V, which is suitable for relay driving and industrial automations applications. The LPCI-7230 also provides two interrupt sources on digital input channels, which are easily user configurable.
-
Product
Four And Two-Port Multi-Protocol RS-232/422/485 PCI Express Mini Cards
mPCIe-COM-4SM Family
-
The mPCIe-COM-4SM family of cards feature high performance 16C950-class UARTs. Available in 4-port and 2-port versions, each port is capable of communication speeds up to 921.6kbps in RS-232 (differential modes support speeds as high as 3Mbps) and has 128-byte deep transmit and receive FIFOs. Large FIFOs protect against data loss in multitasking operating systems, reduce CPU utilization, and improve data throughput, while reducing or eliminating inter-character or inter-packet pauses. The advanced integrated circuit with pre-scalar supports a wide variety of custom baud rates, and any rates not otherwise achievable can be supported via a custom factory-installed crystal oscillator (up to 10Mbps!).
-
Product
PCI Synthesizer
SYNTH300 Series
-
These devices provide two synchronized DDS-based RF channels on a single PCI card. With fine frequency and phase control, triggered operation, and the ability to accept an external clock, the Synth300 products enable a number of advanced applications at a fraction of the cost of conventional equipment. In addition to two analog outputs, the product can be ordered with one (or two) LVDS outputs for programmable digital clock applications, and can be configured for control by externally supplied TTL signals for low-latency triggered operation such as PSK, FSK, and triggered sweep operation.
-
Product
PCI High Density Screened MUX 10 Ch 8 Pole
50-670-021-S-10/8
Multiplexer Module
The 50-670 series of very high density multiplexer cards feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
XMC-to-PCI Express (PCIe) Adapter
9956
-
The Technobox XMC-to-PCI Express adapter with Rear I/O support permits use of a standard VITA 42.3 air-cooled XMC or VITA 20 conduction-cooled XMC in the smallest possible edge finger PCI Express form factor. The length of the adapter is the length of the XMC and 10 mm mezzanine stacking height is supported. The height is a standard PCI Express board and is not the low-profile version.
-
Product
64-bit PMC to PCI Adapter
4930
-
This passive PMC to PCI Adapter permits delivery of PMC-derived applications in a standard PCI environment.
-
Product
14 bit, 125 MS/s PCI Digitizer
ATS460
-
ATS460 has been designed from the ground up for OEM applications, which require very high reliability, high performance, high quality and reasonable prices. ATS460 uses COTS analog components and FPGAs to provide you more features and benefits and at the same time reduced manufacturing costs without compromising quality. The result is that you get more digitizer for less money.
-
Product
72-lane, 36-port, PCI Express
PEX89072
-
The new PCIe Gen 5.0 (32 GT/s) PEX89000 series builds on the longevity of the Broadcom series of switches, now spanning 13 families. The PEX89000 family allows customers to build systems from simple PCIe connectivity inside the box to high-performance, low-latency, scalable, cost-effective PCIe fabrics for composable hyper-scale compute systems supporting ML/AI and Server/Storage applications.
