Automatic Test Systems
execute test program sets automatically. Also known as: ATS
See Also: Automatic Test Equipment, ATE Integrators
-
product
Ferroelectric Test System
RT66B
Radiant's Rt66B offers amazing performance at an affordable price. The Rt66B is a perfect entry level system for measuring Ferroelectrics. This system does include Radiant's famous Vision Data Management System which offers all the standard measurements of ferroelectrics including Hysteresis, Fatigue, Waveform, C/V, I/V, PUND and much more.
-
product
Automatic Tuners10MHz – 140GHz
Load Pull
An impedance tuner is an apparatus, which generates controllable reflection factor (Impedance) over a certain frequency range.
-
product
High Temperature Component Test Fixture
16194A
Measure both axial/radial leaded devices and SMD within the temperature range from -55 to +200°C.
-
product
Modular Test System
IMU-MGS
Modular test system with colour touch screen and intuitive software. An integrated help with graphics guide the user through fast and efficient setup and operation. The system is used for CE mark testing in the European Union.
-
product
Handover Test Systems
Family of handover test systems designed for handset-to-network handover testing. Internal step attenuators allow the RF signal between the network access points and the handsets to be dynamically faded up/down. The Ethernet/Serial models run our latest generation 3.x.x firmware that features easy to use ASCII formatted commands.
-
-
product
Switch Box for Fully Automatic Testing
CP SB1
The switchbox CP SB1 reduces wiring work at power transformers. Thereby, the time needed for testing can be reduced and, at the same time, safety can be significantly increased.
-
product
Automatic Power Factor Controller
Nippen Electrical Instruments Co.
NIPPEN Model UNO+ is used for measurement and control of PF using Reactive power compensation. Capacitor banks are suitably switched ON and OFF automatically to provide necessary compensation.An Intelligent switching algorithm (Wear leveling) ensures uniform aging of the capacitors used to achieve the Target PF. An Alarm function ensures protection of capacitor banks against abnormality in voltage, current and sets value of capacitors whenever these are beyond the higher and lower threshold limits.CT polarity is automatically sensed internally in the event of reverse connection.
-
product
Power Device Testing System
Devices that control electric power, and are used in automobiles and a wide range of electrical products.
-
product
Battery Test System
WBCS3000Ls32
Low current model32 channel battery cycler (expandable up to 128 channels)No. of minimum channel : 16 channelsmax. voltage range : ±5Vmax. current range : ±10mA
-
product
Count Down Test System
The Second Launch Pad Count Down system is implemented using VXI hardware designed by Data Patterns specific to the application requirements, featuring a redundant system handling upto 14000 I/O points.
-
product
Circuit Breaker Test System
TDR900
It operates and records a circuit breaker’s contact timing, motion, velocity, main contact engagement & synchronization, trip and close coil initiation and currents.
-
product
Tire and Wheel Testing Systems
Advanced Telemetrics International
Tire and Wheel Testing Systems can be custom designed and manufactured for practically any application. The inductively powered system is used to wirelessly measure tire pressure and temperature during testing.
-
product
Modular Test Systems
Whether thin film, thick film, MEMS, multilayer or bulk: With test systems from AixACCT Systems, you can characterize your piezoelectric materials both in development and during production with the greatest accuracy.
-
product
Low Voltage Burn-in and Test System
Max 450
For burning-in and testing DUTs such as microprocessors, DSPs and logic devices, which require low voltage. Output monitoring gives functional test results for every device during burn-in
-
product
PXI based Test Systems Module
PXI XJLink2
The PXI XJLink2 module allows the integration of XJTAG into PXI-based test systems. PXI XJLink2 has one JTAG controller that can be connected to up to 4 JTAG chains, which are configurable for pinout and voltage. It is easily integrated with LabVIEWTM with a full set of Virtual Instruments (VIs) included.
-
product
Partial Discharge Test System
TPP
The Partial Discharge Test System type TPP is used for non-destructive insulation and quality testing of electrical components (for example according VDE 0110-1, EN 50178, IEC 60270 and IEC 60060).
-
product
Meter Testing System
ASTel
Three-phase Meter Test Equipment of ASTeL 3.2x.x series system is a fully automatic system enabling simultaneous, multi-position calibration and legalization of electric energy meters. The automatics include power sources, reference standards, stand controllers, photoelectric scanning heads, separating transformers, and other elements of the system. All these elements are controlled through a Windows based executive program.
-
product
Computer Based Audio Component Test System
DATS V3
Rugged aluminum housing with detachable test leads and built-in precision calibration resistorTighter tolerances on internal components for more precise measurementsIncreased output capability means greater separation from the noise floor, resulting in more accurate measurementsDATS Linearity Test for comparing parameters and impedance plots at multiple drive levelsOptional under desk mounting brackets included to save desk spaceOnly 1" H x 2-1/2" W x 4-1/8" D for easy portability
-
product
Tensile Testing System With Thermostatic Chamber
This thermostatic chamber is ideal for long-stroke tensile testing of large-elongation materials such as rubber and plastic in controlled temperature environments.
-
product
Single Event Effects Test System
SEE-RAD
The SEE-RAD test system brings together the proven features of our ETS780 tester (such as true APG memory test and powerful FA tools) with the newest technology of the Griffin III. With all new high-accuracy DC Parametrics, superior precision pin drivers, and capture memory of 64M, the Griffin SEE-RAD combines the newest innovations in the test industry with our years of experience in Radiation Test.
-
product
Battery & Electrical System Testing
12-0200
Vehicle Battery Systems fitted to modern cars require a complex system to control and maintain the best charge and discharge rates which not only ensures the longest in service life but also that systems such as Stop/Start operate correctly. The 12-0200 gives the operator access to all the functions complicated and time-consuming manufacturer scan tools have to perform the same function but in a fraction of the time. On average the total time required by the technician to reset a system will be 30 seconds.
-
product
Pneumatic Horizontal Shock Test System
KRD12 series
The KRD12 series shock test system is used to measure and determine the horizontal impact resistance of a product or package, and to evaluate the reliability and structural integrity of the test unit in a horizontal impact environment. The system can perform conventional half-sine wave, post-peak sawtooth wave, or trapezoid wave shock test to realize the shock energy that the product is subjected to in the actual environment, thereby improving the product or packaging structure.
-
product
Train Protection and Warning System and Automatic Warning System
TPWS and AWS
The current Network Rail UK protection systems are TPWS and AWS. The functionality of both systems is combined in a single system, generally referred to as TPWS. TPWS comprises of OSS (Overspeed Sensor System) and TSS (Train Stop System).
-
product
Electro-Optical System Test Bench
IRCOL
Optical collimators and universal electro-optical test benches.
-
product
EMC Test System
An electric product might cause the malfunction to other electric appliances by discharging the emission noise from it, or is oppositely caused the malfuction by the emission noise from other electric appliances. The former is checked by the EMI test and the latter is checked by the EMS test. The international standard like the CISPR standard is provided so that such an accident should not happen, and the manufacturer must declare by themselves beforehand that their product meets the standard. The generic name of the EMI test (Electro-Magnetic Interference) of the emission measurement and the EMS test (Electro-Magnetic Susceptibility) of the immunity
-
product
Test System
Griffin III
The Griffin III system brings new price/performance efficiency to the Tester-in-a-Head tradition, a concept created and introduced by HILEVEL in 1987. This tester is a superior cost-effective solution for Engineering, Production, and Failure Analysis test applications.
-
product
PMS Leak Test System
The system (Pressure Measuring System) is a portable, complete system for leak tests. This consist of the pressure test kit PMS3000 for performing leak tests with an integrated graphic-capable 4.3” color touch display and a pressure relief kit DAK2000 for discharge test according to W400-2, Part 16 pressure loss methods as well as DIN EN 805. The system is complemented by a variety of connection accessories like the rugged accessory case (individually equipped), the test standpipe PSR and accessories for building gas connection as well as the electronically controlled test pumps EPP and the compact air compressor KLK1030.
-
product
Scienlab Battery Test System – Cell Level
SL113XA | SL100XA Series
The cell is the basis of any battery system and directly influences its function, performance and safety. Therefore, it is essential to test and characterize the cell at an early development stage. For this purpose, Keysight offers reliable test systems for precise and reproducible measurement results. The Cell Level Series (SL1002A, SL1004A, SL1007A, SL1132A and SL1133A) — also known as Battery Cell Tester — emulates sink and source for battery cells for automotive and industrial applications.
-
product
TDR Test System
GATS-310
The GATS-310 TDR test system provides you with the ability to test nets as down to less than 1/2" in length using Industry Standard Techniques.
