Solder Joint
-
Product
Pin-Line™ Collet Socket with Solder Tail Pins
Series 0513
-
Pin-Line Collet Sockets with Solder Tail Pins. Features: Rows of socket strips may be mounted on any centers and are end-to-end or side-by-side stackable for .100 [2.54] grid or matrix patterns. Available with solder tail or wire wrap pins. Consult Data Sheet No. 12014 for wire wrap pins. Break feature allows strips to be cut to the number of positions desired.
-
Product
Connector, 104-Pin D-Type Male, Solder Bucket, 5A
40-960-104-M
-
This 104-pin male D-type connector allows users to create their own cable assemblies. Cable connection is via solder buckets - supplied with rear cable entry backshell.
-
Product
Solder Paste Inspection Machine
3D SPI
-
The 6500 series is the measurement equipment provided by Jiezhi Technology for the small pads of solder paste printed on the PCB board. It will cause defects such as sharpness, offset, more tin, and less tin printing during solder paste printing. Causes defects in the later stage of production, this equipment can find problems in advance
-
Product
3D Solder Paste Inspection (SPI)
TR7007 SII
-
Offering inspection speeds of up to 200 cm2/sec, the TR7007 SII is the fastest solder paste inspection system in the industry. This highly accurate inline shadow-free solder paste inspection solution offers full 3D inspection at resolutions of 15 µm or 10 µm. Built on a high precision linear motor platform, the system's hallmark features include closed loop function, enhanced 2D imaging, auto-warp compensation and fringe pattern technology. Increase capacity without sacrificing additional space with an available dual-lane configuration.
-
Product
Waveguide Rotary Joints
-
Waveguide Rotary Joints are used for the rotary transmission of power and signal between the stationary and rotating parts of a radar or satcom system.EVERAXIS has designed and produced single and multi channel Waveguide (WG) Rotary Joints since 1958. Every new design is simulated in FEM software as well as physically tested for optimal performance. Each high power Waveguide Rotary Joint is tested at maximum peak power before shipment.
-
Product
High-speed 3D Solder Inspection Machine
YSi-SP
-
a high-speed 3D solder paste inspection machine that enables high-speed high-accuracy inspections based on our “1-head solution” concept for using a single type of head to handle various inspections. It is used to inspect the printing quality (volume, height, area, misalignment) of solder paste after it has been printed onto PCBs. Available April '18.
-
Product
Solder Paste Printers
-
Shenzhen Leadsmt Technology Co.,Ltd
Is mainly used to print the solder paste to the circuit board, is one of the essential equipment in electronic manufacturing.
-
Product
68-Pin SCSI Micro-D Female Solder Bucket
40-962-068-SB-F
-
This connector is designed to allow users to directly terminate with soldered connections to the 68-Pin SCSI Style Micro D connector. Pickering Interfaces recommends the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
Product
Solder Test Pallet
WaveRIDER® NL 2
-
The wave soldering process is one of the most challenging procedures to set up. The ECD WaveRIDER NL 2 greatly simplifies wave solder set up and ensures perfect repeatability, time after time. Board recipe preheat temperatures, conveyor speed, wave height, contact times and parallelism are all measured and monitored using the WaveRIDER NL 2 process pallet.
-
Product
9-Pin D-Type Male, Solder Bucket, HV
92-960-009-M-HV
-
9-Pin Male D-Type Connector, High Voltage, Solder Bucket - Without Backshell
-
Product
Connector, 104-Pin D-Type Female, Solder Bucket, 5A, 4-40 UNC Screwlocks
C104DFR-2SB-1A
-
This 104-pin female D-type connector allows users to create their own cable assemblies. Cable connection is via solder buckets - supplied with rear cable entry backshell. This connector is suitable for use with Pickering modules that use the 104-pin D-type connector.
-
Product
68-Pin Micro-D Male Solder Bucket With Backshell
40-962B-068-SB-M
-
This connector is designed to allow users to directly terminate with soldered connections to the 68-Pin SCSI Style Micro D connector. Pickering Interfaces recommends the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
Product
25-Pin D-Type Male Solder Bucket
92-960-025-M
-
This accessory is designed to allow users to directly terminate a cable with soldered connections to the connector. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical precautions are observed.
-
Product
96-Pin 1.27mm Pitch Female Solder Pad Connector With Backshell, Screwlocks
C096SFR-4SP-5A
-
This connector is designed to allow users to discrete wires using solder pad connections to the 96-Pin 1.27mm pitch connector. Pickering Interfaces recommends the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
Product
SparkFun Solder-able Breadboard
-
This is the SparkFun Solderable Breadboard. A bare PCB that is the exact size as our regular breadboard with the same connections to pins and power rails. This board is especially useful for preserving a prototype or experiment you just created on a solderless breadboard by soldering all the pieces in place.
-
Product
Solder Paste Inspection System
LaserVision SP3D Mini
-
The LaserVision SP3D Mini offers the same level of overall measurement capabilities as the VisionPro SP3D. Utilizing a lower cost microscope platform and the ability for customers to supply their own PC if needed, the SP3D Mini sets the "affordable" boundary on reliable, low cost SPI solutions.
-
Product
Reflow Soldering Machines
-
Shenzhen Leadsmt Technology Co.,Ltd
Used to attach surface-mount components to printed circuit boards (PCBs). It involves applying solder paste to specific locations on a PCB, placing the components on the paste, and then heating the assembly in a reflow oven.
-
Product
Coax, Patchcord, ITA, 20", Mini Coax, Solder Sleeve, RG316 Tan, Single-Ended
7-339116000-036
-
Mini Coax, ITA, Solder Sleeve (50 Ohm, 2 GHz) to RG316 Tan (50 Ohm, 3 GHz).
-
Product
Mini Coax, Contact, ITA, Solder Sleeve, RG316 & RG178
610103140
-
Mini Coax, Contact, ITA, Solder Sleeve, RG316 & RG178.
-
Product
3D Solder Paste Inspection Machine (3D-SPI)
3Si Series
-
Saki's 3D SPI identifies critical defects and assists with process improvement.
-
Product
Solder Paste Wetting Tester
SP-2
-
SP-2 is wettability testing machine forsolder paste, parts electrode and PC board,adopted SP-Tension-Method (Temperature Profile Method).
-
Product
37-Pin D-Type Male Solder Pin HV
40-960-037-MHV
-
This connector is designed to allow users to directly terminate cables with soldered connections.
-
Product
Multi Mode Fiber Optic Rotary Joints
-
Multi Mode Fiber Optic Rotary Joints (FORJ) can be supplied as a stand alone product with customized features (wavelength, connectors, fiber).
-
Product
68-Pin VHDCI Connector, Slimline - Male, Solder
C068VMR-6SB-6A
-
This slimline version of the VHDCI connector is designed to allow users to directly terminate a cable with soldered connections to the 68 Way VHDCI connector. It is difficult to terminate cable to the 68 pin VHDCI because of the high density and fine pitch. Pickering Interfaces recommends the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
Product
96-Pin 1.27mm Pitch Female Solder Pad Connector Without Backshell
C096SFX-XSP-5A
-
This connector is designed to allow users to discrete wires using solder pad connections to the 96-Pin 1.27mm pitch connector. Pickering Interfaces recommends the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
Product
Replacement Solder Tip Lead Set for D410/D610
Dx10-SI
-
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
Product
Replacement Solder Tip Leadset for Use with D410/D610
Dx10-SI-HiTEMP
-
The 90 cm HiTemp cables and Solder-In lead can be used for controlled situations where the differential amplifier module needs to be removed from the extreme temperature environment. Ideally suited for testing scenarios where the temperature can fluctuate from -40 °C to +105 °C.
