Dielectric Strength Testers
check insulation to assure current does not flow through it.
-
product
Field Strength Meter
FIM-72A UHF
The Model FIM-72A is a portable, laboratory quality Field Strength Meter designed for rigorous field applications. Combining a calibrated half-wave dipole antenna and a highly accurate tuned voltmeter with a range of 140 dB, the FIM-72A is suitable for practically all types of RF emission measurements in the 450 MHz to 960 MHz spectrum. The operator can switch select wide or narrow bandwidth, peak or average value of TV or pulse modulated signals, AM or FM demodulation, and meter dynamic range of either 20 dB or 60 dB. A dc analog voltage, proportional to meter indication, is provided for driving a chart recorder or similar device. A leveled output from the calibrating generator is available for measuring cable insertion loss, filter response, amplifier gain, VSWR, and other signal ratio measurements. The 4-1/2 inch, taut band, mirrored scale meter is calibrated in volts and dB for precise measurements in field or laboratory environments.
-
product
Electronic Tearing Strength Tester
DRK108B
Shandong Drick Instruments Co., Ltd.
DRK108B Electronic Tearing Strength Tester is the special instrument for tearing strength test. In paper making industry, packaging industry, science and research industry and supervision and inspection industry, it is necessary.
-
product
Field Strength Analyzer
SRM-3006
Selective measurement of high frequency electromagnetic fields. Complete, easy to use test system, consisting of a base unit and measuring antennas, for non-directional detection of fields and their sources in the frequency range from 9 kHz to 6 GHz and from 24.25 GHz up to 29.50 GHz with 5G FR2 Antenna.
-
product
Automatic Dielectric Tester
LD-LADT-A10
Automatic Dielectric TesterLD-LADT-A10is a fully automatic oil tester. The oil tester adopts industrial SCM to control which is applied to integrate circuit. It features anti-jamming technology which largely improves the machine capacity.
-
product
Strength And Hardness Testing
Strength measures how much stress can be applied to an element before it deforms permanently or fractures. Hardness measures a material's resistance to surface deformation.
-
product
Dielectric Loss Tangent and Transmission Attenuation Measurement System
RTS03
RTS03 measures relative permittivity (dielectric constant), dielectric loss tangent in the frequency range between 5GHz and 26.5GHz based on a correlation between measurement frequency and transmission attenuation as the microwave passes through the flat plane sample.
-
product
Broadband Isotropic Field Strength Probes
PI-01, PI-01E, PI-03, PI-05
Modern design probes meeting the requirements of most EMC and RF safety standards for RF safety, industrial, military and radar communication applications: 0.2-1000 V/m, 10 KHz-40 GHz.
-
product
Field Strength Calibration Probe
Beijing KeHuan Century EMC Technology Co,.LTD
Three-axis omnidirectional 100kHz～6GHz light transmission.
-
product
Extensometers for Creep Compliance and Tensile Strength Testing of Asphalt
Model 39
Jinan Testing Equipment IE Corporation
Designed to many of the needs for testing asphalt core samples in 4 and 6 i ch diameters. The unit meets test method requirements for strain measurement developed under the U.S. Federal Highways SHRP program.
-
product
Insulating Oil Dielectric Loss Tester
HTYJS-H / 275
Wuhan Huatian Electric Power Automation Co., Ltd.
Used for measuring dielectric loss and resistivity of insulating oil.
-
product
Electronic Tensile Strength Tester Pull Force Test Chamber Applicable Industri
Shenzhen Chuangxin Instruments Co., Ltd.
This machine can test various materials (both finished and semi-finished products ) of tensile strength ,compressive strength and elongation ,can do stripping ,tear strength ,flexural ,compression test and etc. It can connect up to the computer and display or printout the test times , test value , max. value , etc . Also it can make various report forms according to the requirements .
-
product
Dielectric Resonator Oscillators
Dielectric resonator oscillators (DRO) are free running oscillators that utilize state-of-the-art planar circuits, three-terminal devices and dielectric resonator technology to generate high-quality microwave signals with excellent frequency stability. In addition, these oscillators are equipped with an internal voltage regulator that further improves the frequency stability by isolating the external bias pushing and modulation. In general, these oscillators are fixed. However, a small mechanical or electrical tuning range can be achieved by use of a self-locking screw or an integrated Varactor diode. The standard offering covers the frequency range of 2 to 40 GHz. While standard models are equipped with female SMA and K connectors at the RF port, other RF interface options are also available.
-
product
Transformer Oil Dielectric Strength Testing
LS -JJ-II
Chongqing Lushun Scientific & Technological Development Co., Ltd.
1.The instrument has the function of automatic detection. 2.Tiny TPU-A panel printer is adopted for automatic printing out type insulating oil dielectric strength ATE is a full self-reacting device, which is developed according to the requirements in International IEC-156 and International GB507-86 "Insulating Oil Dielectric Strength Mensuration", combining the feedback opinions of all users .The instrument adopts singlechip as the leading part, and uses the method of "first setting and then testing". The whole process is controlled by automatic microcomputer. It is operated simply and used conveniently.
-
product
Rub Tester and Abrasion Tester
RT4
This comparative test works by abrading a printed sample against a reference material under known conditions. The results can be used to identify alternative substrates, better ink and coating formulations or the suitability of finished cartons, films or printed books, magazines and promotional materials.
-
product
RF Signal Strength Meter
006
Hand Held RF Signal Strength Meter. Detects RF Activity around centre frequency. Available for 315MHz, 433MHz, 868MHz, 869.85MHz, 914.5MHz.
-
product
Leak And Seal Strength Detector
LSD-02
Jinan Leading Instruments Co., Ltd.
LSD-02 Leakand Seal Strength Detector is applicable in the quantitative measurement of leak, heat seal strength, heat seal quality, and burst pressure of each heat sealedges of the flexible packages that are made using heat seal and adhesiveprocessing, as well as sterilized packages; the quantitative measurement ofleak performances of all kinds of plastic pilfer-proof closures; thequantitative measurement of the unitary airproof, compression resistancestrength, cap body joint strength, cap disengaging strength, seal strength ofedge and butting strength of various flexible tubes. It can also provideevaluation and analysis for the compression and burst resistance strength ofthe materials of flexible packaging bags, the torsional airproof index of cap,the cap joint and disengaging strength and the stress strength; as well as theairproof performances, the compression resistance performance and the burstresistance character of unitary bottle, etc.
-
product
Tensile Strength Tester
Capacity of Tester with accuracy of 100g : 250 Kgf. and 500 Kgf.Capacity of Tester with accuracy of 10g : 20 Kgf, 50 Kgf and 100 KgfS Type Load Cell fixed with Top GripTraverse Speed: 300 & 100mm /min.Grip Separation: 1000 mmGrip Separation: 25 mmTop Grip is fixed and Bottom Grip is Movable Type.Elongation measurement by Steel Scale and Digital Counter Meter Both.Digital Display of Load and Elongation.Peak value of last test can be read.User friendly key panel with switch of zero setting and peak value of last testMotor: 1/2 HP single phase 220V 50 Hz. ( for Capacity up to 100 Kgf )Motor: 1 HP single phase 220 V 50 Hz ( for Capacity up to 500 Kgf)Power: 220 V AC 50 Hz.Safety device by limit switch to protect from over traverse.
-
product
Shoe Dielectric Resistance Tester
UI-FT07
Shoe Dielectric Resistance Tester, also named as shoe high voltage withstand tester, is used to test shoe sole and heel electrical insulation, to check shoe performance of voltage withstand and current leakage. It is to test safety shoe dielectric resistance ability (Electrical Hazard Testing) as mentioned in ASTM F2412.
-
product
Loss Tangent M in Dielectric Oil
TAND220A
The measuring instrument type TAND220A complies with the international standard IEC 61620. The instrument is based on the so-called "low-amplitude, low-frequency alternating current square wave method" and allows accurate measurements of conductivity and relative permittivity. Conductivity measurement in the range of 0.01 pS/m to 20,000 pS/m allows the use of this instrument for quality control of high resistivity liquids even at room temperature. The TAND220A works with a low test voltage and also with a low test current so that it does not represent a danger for the operators.
-
product
Dielectric Strength Meter
Dielectrotest
The Dielectrotest is a fully automatic dielectric oil meter for determining the breakdown voltage of insulating liquid. It is designed for both laboratory and field use for commissioning and maintenance purposes. The test standard is selected via menu.
-
product
Capacitor Tester
MIG0603CAP
The MIG0603CAP consists of two circuits with impulse capacitance 20 µF and 0,25 µF. Both circuits generate a voltage wave shape 1,2/50 µs and are combined in a 4 unit height 19" rack. The generator circuits are defined in IEC 60384-14 and EN 132400. The serial resistors Rs, the impulse capacitor CT, and the load capacitance Cp will be automatically switched when different capacitance ranges are selected on the MIG0603CAP.
-
product
Voltage Tester
HH2611
Handy, quick response and easy to use tool. Safe to use Non-Contact testing 90-220V AC voltage. Delect AC voltage without connecting into the wire circuit. Very bright LED and buzz sound alarm if voltage is present. Used to detect where the wire is broken. Used to detect whether an outlet is present of voltage. Used to detect a broken Christmas bulb out of a series of connected Christmas bulbs
-
product
Epstein Tester
S21 and S21R Series
Incoming material inspection can be very useful where strict quality standards are maintained. It saves a lot of processing cost since lossy material is inspected at the entry level before it goes to production level. Epstein Stack testing is one of the oldest and widely used methods for electrical sheet testing.
-
product
Transformer Testers
*Quickly tests deenergized power distribution transformers*Briefly energizes the transformer and takes a snapshot of the condition by measuring the voltage, current and power factor of the test signal*Tests overhead, pad-mount and distribution transformers*Audible alarm confirms successful test*Improve SAIDI statistics by quickly testing and getting the transformer back in service*Auto self-test performed with every test*Compact, lightweight and easy-to-use
-
product
Terminal Mechanical Strength Test
The terminal strength test is used to performed to determine whether the design of electrical terminals and their method of attachment can withstand mechanical stresses to which they will be subjected during installation or disassembly in equipment. These stresses must be withstood by the component without sustaining damage which would affect either the integrity of the terminals or the operation of the component part itself. Procedures are established in this method for testing, for example wire-lead terminals, flexible-flat-strip or tab-lead terminals, and rigid-type terminals which are threaded or have other arrangements for attaching conductors. The forces applied during the test consist of direct axial, radial or tension pulls, twist, bending torsion, and the torque exerted by the application of nuts or screws on threaded terminals.
-
product
Scratch Tester
CSR1000
This tester is highly effective in measuring the adhesion strength (adhesion strength) of hard coatings (Ti, TiN, SiC, DLC, etc.) formed by PVD and CVD on metal surfaces such as cemented carbide. Adopting a scratch test method that allows quantitative measurement with simple operations, the film surface is scratched while increasing the load on the sample surface, detecting film breakage with high sensitivity, and providing the load at which film breakage occurs (critical load). tools and mold tools that require
-
product
Puncture Testers
Mechanical puncture testers check the puncture resistance or hardness of materials like dry wall, foam boards, cardboard, etc. They are ideal for handheld penetration tests or mounting to a test stand and intrinsically safe in hazardous environments. An optional handle is available.
-
product
Vector Tester
PVT360A
The R&S®PVT360A is a VSG/VSA single-box vector tester optimized for FR1 base station, small cell and RFcomponent testing in production and characterization environments. Two independent signal generatorsand analyzers enable fast parallelized measurements. A frequency range of up to 8 GHz, flexible bandwidth configuration and an optional second TRX channel provide the necessary performance and enable flexible adaptation in a small form factor.
-
product
Torque Tester
WDIS series
Management of various torque tools PLC and connection alsoWDIS-IP (05/5/50/200/500/1500), WDIS-RL (005/05/6/10), WDIS-IPS (05C/5C/20CL). The DIS series has become easier to use and has higher performance. Interlocking with a personal computer or PLC, the torque measurement can be managed at a higher level.Management of manual torque drivers and wrenches, management of automatic and semi-automatic tools, inspection of screw tightening and loosening torques
-
product
Rotor Tester
SL Series
Shanghai Aoboor Electric Co., Ltd.
Applicable for testing fully opened, fully closed squirrl-cage rotors with process slot, with or without shaft, it can identify broken bars, slim bars, under-casting, porosity, sand holes, residues, improper end rings, internal short circut in bars, eccentricity.
