Battery Load Testers
determine the condition of batteries to provide power.
See Also: Battery Capacity Testers
-
product
CCA-006 Battery Probes
Current Rating (Amps): 5Average Probe Resistance (mOhm): 50Test Center (mil): 125Test Center (mm): 3.18Full Travel (mil): 78Full Travel (mm): 1.98Recommended Travel (mil): 40Recommended Travel (mm): 1.02Overall Length (mil): 669Overall Length (mm): 16.99
-
product
Battery Discharger & Capacity Tester
Fuzhou Fuguang Electronics Co., Ltd.
Battery Discharger & Capacity Tester
-
product
Hand-Held/Digital Load Tester
6030
• Full 125 Amp load tests 12 Volt batteries, alternators and starters on all type of vehicles• PATENTED• Made in USA of US and Global Components
-
product
Load Board
cPCI 3U
Load boards are essential in keeping any system in top running shape. As a full-system provider, Hartmann strives to not only provide the systems you need, but the supporting hardware as well.
-
product
Hand-Held Alternator/Battery Load Tester
6024
• Full 125 Amp load tests 12 Volt and 24 Volt Batteries, alternators and starters on all types of vehicles• PATENTED• Made in USA of US and Global Components
-
product
Battery Leak Testers
Battery leak testers are crucial tools in the quality assurance process for battery manufacturing. These testers are designed to detect any leaks in battery cells, ensuring that the batteries are safe and reliable for use. Battery leaks can lead to reduced efficiency, potential damage to devices, or safety hazards. By employing sophisticated techniques, such as pressure decay methods or helium detection, battery leak testers can identify even the smallest imperfections in battery casings. These testers are essential in industries where battery reliability is critical, such as in automotive, consumer electronics, and renewable energy sectors, ensuring that the batteries meet stringent safety and quality standards.
-
product
Battery Tester
G5.BT
The G5.BT series is bidirectional regenerative. It was developed specifically for testing energy storage devices and is suitable for use in laboratories and on test benches. The modular and finely graded G5.BT series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3. The G5.BT series has an outstanding current accuracy of <0.02% FS, an additional high-resolution current measurement range, and a fast current rise time in the 100 μs range. Ripple modulation, an integrated safety relay for PL c according to EN ISO 13849 and a powerful CAN multi-protocol interface (1 kHz, 16 bit) as well as functions to avoid reverse-polarity problems, current surges, and unwanted deep discharges make the G5.BT series the ideal, versatile battery module and battery pack tester.
-
product
5V1mA Button Battery Tester
TOB-BST8-5V1mA
Xiamen Tob New Energy Technology Co., Ltd
8 Channel Battery Analyzer (0.002-1mA, up to 5V) with Laptop & Software for R&D Battery Materials. TOB-5V1mA Button Battery Tester is an eight-channel battery analyzer to analyze small coin cells with a range current 0-50mah, voltage 0-5v. Each channel of the analyzer has independent constant-current and constant-voltage source, which can be programmed and controlled by computer software.
-
product
Battery Short Circuit Tester
TOB-BSCT-01
Xiamen Tob New Energy Technology Co., Ltd
Battery Short Circuit Tester For Not Charging Semi-Finished Battery Core Checking Out. This Battery Short Circuit Tester is used for check out NG batteries for battery core without electrolyte filled or before battery charging. For lithium battery research, it is used for battery core after winding process or stacking process to check out bad battery with automatic alarm.
-
product
Laboratory Battery Tester
Compact and versatile, our portable desktop solution integrates Arbin's advanced testing features.
-
product
Battery Testers
Wuxi IMHOO Technology Co., Ltd.
Voltage of batteryBattery type1.5VButton Cell, AA,AAA,C,D,N3V Lithium6V Camera Battery9V 12V 15V 22.5V Power Source Not use batteryWeight 260gmeasurement 100x63x33mmPacking50pcs/CTN
-
product
Battery Capacity Tester
BLU-A Series
The battery capacity test is performed to determine the health of a battery. DV Power’s battery load unit BLU-A is a portable, powerful, and lightweight solution for battery capacity measurement. It is applicable to any battery string such as lead-acid, Li-Ion, Ni-Cd, etc., with up to 500 V battery voltage. As a special feature, BLU100L model enables the capacity testing of a single Li-Ion cell.The capacity test is performed in an accurate and user-friendly way. Also, it is in accordance with battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22, and other relevant standards.Battery load unit BLU-A enables setting discharge currents up to 240 A, with a resolution 0,1 A. Furthermore, if higher currents are required, BLU-A units can be connected in parallel, or additional BXL load units can be used.The instrument offers the best power-to-weight ratio in the market. BLU-A models start from 12,8 kg / 28.2 lbs and deliver up to 28,4 kW of power.The user can select three discharge modes:Constant current,Constant power,Constant resistance.Additionally, different battery duty cycles can be simulated using user-selectable discharge profiles.The instrument monitors discharge parameters in real-time during the capacity test. A 4,3-inch touch screen display shows battery voltage, current, elapsed time, and capacity during the entire test. Also, BLU battery load unit can be used with DV-B Win software. As a result of that, a user can see a detailed numerical and graphical presentation of key parameters and can create reports in various formats.Testing with BLU-A doesn’t require a disconnection of the battery from the testing equipment.
-
product
Standby Battery Testers
Franklin Electric - Grid Solutions
A user-customizable, flexible, efficient and economical battery management tool for service providers, operations, and maintenance teams.
-
product
Lithium Battery Inspection Tester
C19
Fuzhou Fuguang Electronics Co., Ltd.
C19 series is a portable tester which can quickly inspect battery pack of two-wheel vehicles. It can realize quick inspection and selection of SOH data of battery pack and discharge-charge maintenance. Data can be transferred to the mobile phone APP through Bluetooth forming a statistics report and faulty cell warnings so that further maintenance solutions can be developed in time.
-
product
Unclamped Inductive Load Tester
ITC55100STD
Model ITC55100STD performs ruggedness testing of power MOSFETs and IGBTs. It also tests single and dual diodes, and forward and reverse bias of IGBTs when used with an optional ITC55-RSF Output Selector Box.
-
product
Battery Conductance Tester
FST-8000
Foresight Electronics Co., Ltd.
Profsional battery conductance tester for Lead-acid stationary (wet, flooded, gel, AGM, VRLA) battery cells/blocks, to measure actual capacity and aging for UPS, telecom, industrial, vehicle, solar or other applications' small and large battery banks.Battery Conductance Tester is a portable digital measurement device for testing lead acid stationary batteries health and aging condition precisely within seconds.
-
product
Battery Cell Surge Tester
19311
The Chroma 19311 series battery cell surge tester is designed for testing the insulation quality between the positive and negative plates of the lead-acid battery cell. This is done by applying a high voltage surge/impulse before the electrolyte injection. Its output voltage can reach up to 6kV. It also has four terminal measurement and 200MHz sampling rate. The Chroma 19311 series has single channel (19311) and multi-channel (19311-10) tester.
-
product
120 GBd High-performance BERT
M8050A
The Keysight M8050A high-performance bit error ratio tester (BERT) enables accurate characterization of receivers used in next-generation data center networks and server interfaces. With uncompromised signal integrity, support for NRZ, PAM4, PAM6, and PAM8 signals, and data rates up to 120 GBd, the flexible architecture of the M8050A supports 1.6T pathfinding as well as other leading-edge technologies.
-
product
Unclamped Inductive Load Tester
ITC75300
The ITC75300 is a 400 amp version of the ITC75100 which performs ruggedness testing of power MOSFET’s, IGBT’s and diodes that conforms to MIL-STD-750 method 3470 by stressing them to controlled energy levels, accomplished by the devices driving an unclamped inductive load. Improved Test Specifications allow complete control of test parameters.
-
product
Motorcycle Battery Testers
ELAK Motor-Cycle Battery Testers are designed for testing batteries used in motor-cycles, scooters, ATV''s, etc. These testers check the voltage drop of the battery under a fixed load and confirm the status of the battery full, weak or dead. The new generation motor-cycle and scooters are fitted with an electrical start. It is therefore very essential to test these batteries under load, to ensure that the batteries are capable of starting the vehicle.
-
product
0-10V Battery Voltage Sorter Tester
TOB-0918
Xiamen Tob New Energy Technology Co., Ltd
0-10V Battery Voltage Sorter Tester With Battery Low/High Voltage Alarm For All Kinds Of Batteries. TOB-0918 Battery voltage tester is a Voltage sorter with single-chip control of portable test instrument, This voltage tester is with a voltage limit set and automatic judging function, we can set the voltage in the range or out the range alarm function.
-
product
PET Bottle Vertical Load Tester
VP-1000
VP-1000 PET Bottle Vertical Load Tester is professionally designed to test the top load resistance, container body side load resistance of the PET container.
-
product
Battery Charge and Discharge Tester
HTCFD / 790
Wuhan Huatian Electric Power Automation Co., Ltd.
The voltage monitoring information of single battery is simple, safe and accurate with wireless relay access.
-
product
Wireless Battery System Tester
EECS550
Snap-on Tools has launched the new Snap-on EECS550 Wireless Battery System Tester that eliminates the need for a second technician. “The EECS550 maximizes manpower and gets the critical job of battery system testing done with just one set of hands,” says Dave Brekke, product manager for Snap-on. “Snap-on has listened to techs in shops where this work is a daily task. The tester will change the way techs are able to service cars, trucks, motorcycles, golf carts, ATVs and more. From the strong, built-in magnets that hold the tester in place to the easy-to-see, back-lit screen that displays in eight languages and reports battery, starting and charging system conditions, this tester takes productivity to the next level.”
-
product
CP-2XX-8 Battery Probes
Current Rating (Amps): 5Average Probe Resistance (mOhm): 50Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 88Full Travel (mm): 2.25Recommended Travel (mil): 78.7Recommended Travel (mm): 2.00Overall Length (mil): 315Overall Length (mm): 8.00Overall Length Remark: Overall length does not include tail.Recommended Drill Size: #53 or 1.51 mmRec. Mounting Hole Size (mil): 61Rec. Mounting Hole Size (mm): 1.55
-
product
Battery Extra Load Units
BXL Series
BXL is an extra load unit designed to be used with DV Power’s BLU series battery testers. However, this unit is a universal add-on device. Because of that, it is compatible, as an additional load, with any other discharge/capacity tester in the market.In case when discharge current exceeds the capacity of a single BLU device, BXL can increase the discharge capacity. There are no limitations on the number of extra load units that can be connected in parallel to the main battery tester.A system of BLU and BXL instruments enables performing the capacity test in an accurate, user-friendly way. Also, all instruments are in accordance with battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22, and other relevant standards.These units can be used on any type of battery string, such as lead-acid, Li-Ion, Ni-Cd, etc. They test battery strings with voltages in the range of 5,25 – 500 V DC. On the other hand, current up to 250 A can be discharged through the BXL internal structure.The instrument simulates a constant resistance load during the discharge test. Several resistances can be set for different battery nominal voltage levels. This makes BXL extremely flexible in selecting its load capabilities.
-
product
Battery Tester
CS-3001
The CS-3001 test system records all block voltages, total voltage and current during a discharge test. The modular design makes it easy to connect most of all battery installations, starting from a single block and ending up with 960 block voltages. Up to four parallel strings can be tested. All measuring modules are electrically isolated (600VDC CAT III, 5000VAC test voltage).
-
product
High Load Strength Tester
HLST1000Z
This tester measures the tensile or compressive strength of various samples
-
product
Battery Crush Nail Penetration Tester
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's Battery Crush Nail Penetration Tester is used to simulate the battery penetration test of a sharp object during packaging, transportation, storage, use and disposal.
-
product
Battery Charge Discharge Tester
KV Hipot Power Test Equipment Co.,Ltd
Battery Charge Discharge Tester is a multi-function comprehensive tester which is not only a battery charger and Battery discharger, but a battery activator.
