-
product
Parallel Memory Test Solution
Magnum2
Teradyne’s Magnum 2 test system delivers high throughput and high parallel test efficiency for high performance non-volatile memories, static RAM memories and logic devices.
-
product
Single Slot Intelligent Interface Card
IIB-3910-CPCI
The IIB-3910-CPCI is a single slot intelligent interface card providing complete STANAG 3838 and STANAG 3910 test, simulation and bus analysis capability for the CompactPCI Bus. The IIB-3910-CPCI supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with powerful multi-level triggering capability. Full error injection capability in both 3838 and 3910 modes is provided in BC and RTs modes, with full error detection in BC, RT, BM and CBM modes. Dual redundant 3838 interface, with user selectable dual redundant optical or single redundant electrical 3910 interface are featured. 2 Mbytes of dual ported RAM are provided. The board is supplied with C drivers in source code and Windows menu driven software as standard.
-
product
Module Spectrum
nRF52810 Series
Nordic nRF52810 solutioin features an Arm Cortex-M4 processor with 192 KB Flash and 24 KB RAM with 32 GPIO available. Supports SPI, UART, I2C, PWM interfaces with both Chip Antenna and PCB Antenna option for selection.
-
product
PCIe FPGA Carrier For FMC+, Kintex UltraScale™
PCI592
The PCI592 is based on the Xilinx XCKU115 Kintex UltraScale FPGA, which provides 5,520 DSP slices, 75.9 Mb RAM and 1,451,000 logic cells. The FPGA interfaces directly to the FMC+ DP-23 and all FMC+ LA/HA/HB pairs, making it compatible with a wide range of industry standard VITA 57 modules. It also has interface to three DDR4 memory channels (2x 64-bit wide and 1x 32-bit wide). This allows for large buffer sizes to be stored during processing as well as for queuing the data to the host. The unit has x8 PCIe edge connector routed to the FPGA PCIe Gen3 hard IP block. In addition, 16 uncommitted connection pairs are routed to a dual x8 expansion connector, providing direct connectivity to a neighbouring FPGA (e.g. via Aurora, 10G/40G, SRIO, PCIe) without the need to go through the host.
-
product
Intelligent Interface Card
IIB-1553-CPCI
The IIB-1553-CPCI is an intelligent interface card providing full MIL-STD-1553 test, simulation and bus analysis capability for the CompactPCI bus, with 1553A, 1553B, McAir and STANAG 3838 capability on a single card.The IIB-1553-CPCI supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with comprehensive multi-level triggering capability. Full error injection capability is provided in BC and RT modes,with full error detection in BC, RT, BM and CBM modes. The unit provides a dual redundant 1553 interface.2 Mbytes of dual ported RAM are supplied as standard. The board is supplied with C drivers in source code and Windows menu driven software.
-
product
Open Frame Panel PC
PPC3-6.5-407
The PPC3-6.5-407 from WINSYSTEMS utilizes the E3800 family of Atom™ processors from Intel® to provide low power and high performance in a compact 6.5-inch Panel PC. Designed for harsh environments and reliability, the design includes a sunlight-readable display and soldered RAM for added shock and vibration resistance with operating temperature ranges available from -10°C to +70°C.
-
product
Tip sensor
KELLER AG für Druckmesstechnik
Designed for measuring flow rate and ram pressure in pipework.The probe can be advanced a number of metres into tight canals thanks to dimensions ranging from ø 1,32 mm to ø 2,64 mm and a highly flexible cable.
-
product
16-bit, 200KHz, 16SE/8DIFF Isolated AI, 4 12-bit AO, 8 Optically Isolated Dig. I/O, 24V, 24 TTL I/O
APCI-3116-16
The APCI-3116 is a 16-bit multifunction board for 3.3 V and 5 V PCI systems, with optical isolation up to 1000 V and a high throughput rate of 200 kHz. The PCI board has additional types of conversion: Sequence RAM, Auto Refresh, scan, timer or external event.Furthermore, the board has a PCI DMA, 2 watchdogs, 4 digital inputs and 4 digital outputs. Sensors, which allow to supply current signals instead of voltage signals, also can be acquired with the APCI-3116, as this board offers up to 16 current inputs. The board is protected against overvoltage and input filter and it is protected against high frequency emmission. With the free calibration tool you can do the fine adjustment on-site.
-
product
Bridging And I/O Expansion Versatility. Rapid Hardware Acceleration For Improved Signal Control.
MachXO2
*Up to 256 kbits of user Flash memory and up to 240 kbits sysMEM™ embedded block RAM*Up to 334 hot-socketable IOs that avoid excess leakage*Programmable through JTAG, SPI, I2C or Wishbone*TransFR feature allows in-field design update without interrupting equipment operation*Programmable sysIO™ buffer supports LVCMOS, LVTTL, PCI, LVDS, BLVDS, MLVDS, RSDS, LVPECL, SSTL, HSTL and more
-
product
3.5" Embedded SBC With Intel® Celeron® J1900 Processor, LVDS/VGA/HDMI, Dual LANs, Audio And ZIO
CAPA843
The CAPA843, a fanless 3.5-inch embedded board, features quad-core Intel® Celeron® processor J1900 SoC (codename: Bay Trail). A pair of SO-DIMM sockets supports up to 8GB of DDR3L 1066/1333MHz RAM. The compact size embedded board CAPA843 was designed with emphasis on expandability, offering two full-size PCI Express Mini Card slots, as well as an exclusive Axiomtek ZIO connector. With excellent thermal design, the 146 x 102mm embedded SBC can handle operating temperatures from -20°C to 70°C, and runs on +10V to +24V DC input. The 3.5” fanless embedded board provides three display interfaces with dual-display operation: HDMI, LVDS and VGA. The Axiomtek CAPA843 is an excellent choice for applications in IoT/M2M-related, industrial control, self-serve terminal, gaming, digital signage, POS, and kiosk.
-
product
VME / VSB Module
ADM-42M
The AD42M Data Acquisition Module provides high performance 14-bit digitizing of analog signals for VMEbus applications. The AD42M accepts 4 differential analog inputs via front panel miniature SMC connectors. The AD42M utilizes a signal processor to acquire and store data samples. The AD42M is able to direct the data samples to local static RAM or VSB.
-
product
Acquisition Of 8 Displacement Transducers
APCI-3701-8
PCI interface to the 32-bit data bus Acquisition of 16 or 8 inductive displacement transducers (Half Bridge, LVDT) 8 or 16 input channels ± 10 V 16-bit resolution Measuring frequency up to 100 kHz Conversion can be triggered through software End of conversion can be inquired through software Possibility of interrupt through digital input channels (when a data or a time value is exceeded) PCI-DMA access Onboard FIFO buffers Sequence RAM 16 isolated digital I/O, 24 V Software operation Supported inductive transducers for APCI-3701Standard board APCI-3701-8 or APCI-3701-16Transducer type:
-
product
16-bit, 100KHz, 8SE/4DIFF A/D Inputs; 8 14-bit, 30KHz D/A Outputs, 4 24V Digital I/O, All Isolated
CPCI-3120-8-8
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
product
Memory Testing
C.C.P. Contact Probes Co., LTD.
Standard and Custom test solutions for RAM, Flash and many other memory chips.
-
product
PCI Data Acquisition Boards
Ultraview''s PCI data acquisition add-in cards are complete data acquisition (A/D) and control (D/A) systems on a single PCI Bus card. Ranging in speed from dual 14 and 12-bit 1-25MSPS boards up to 1500MSPS 8-bit boards with 8GB/16GB of on-board RAM. All cards come with graphical waveform viewers, example user programs (source code included) and device drivers for Linux or Solaris, allowing users to quickly prototype and develop their applications.
-
product
8 SE Or 4 Diff. Input Channels, 8 Analog Output Channels, PCI Express
APCIE-3121-8-8
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
product
Standard Airspeeds
These airspeed indicators have unrestrained movements.These instruments are actuated by ram air and ambient atmospheric pressure obtained from the aircraft pitot and static pressure systems. A moveable pointer and a fixed dial indicate airspeed with the zero index at the 12 o??lock position. Temperature compensation is internal and there is no external zero adjustment. Pointer damping is internally adjustable.
-
product
Analog Output Module, 16-bit
IP235A
IP235A modules have a 16-bit D/A converter (DAC) to provide highly-accurate analog voltage outputs. An internal RAM buffer enhances control over the transfer of data to the DAC.
-
product
3-in-1 Analyzer: Logic Analyzer, Protocol Analyzer, Simple DSO
MSO2216B
3-in-1 Analyzer : Logic Analyzer, Protocol Analyzer, Simple DSO• PC-based, USB3.0 interface• 8 / 16 Channels(display digital and analog waveforms of the same channel)• Digital Inputs : 2 GHz Timing, 200MHz State Analysis (Max.)• Analog Inputs : 200 MS/s (Max.), Bandwidth 40 MHz• 8 Gb Memory (Max.)• PC RAM storage for streaming mode• Utility model patent of Taiwan number M601827
-
product
RightMark Memory Analyzer
RMMA
Before this test packet was created there was no proper software for measuring vital system parameters such as CPU/Chipset/RAM providing steady and reliable (reproducible) test results and allowing for changing test parameters in a wide range. Vital low-level system characteristics include latency and real RAM bandwidth, average/minimal latency of different cache levels and its associativity, real L1-L2 cache bandwidth and TLB levels specs. Besides, these aspects are usually not paid sufficient attention in product technical documentation (CPU or chipset). Such test suite, which combines a good deal of subsets aimed at measuring objective system characteristics, is a must have for estimating crucial objective platform parameters.
-
product
External Controller for PXI
External Controllers for PXI are rack-mount controllers that feature high-performance multicore processors, up to 4 GB of dual-channel DDR2 RAM, and optional RAID hard-drive configurations for high-speed streaming to disk. These devices offer hot-swappable fans and options for redundant power supplies. The External Controller for PXI is designed for mission-critical, physically demanding applications.
-
product
PXIe-6571, 1-Slot, 100 MVector/s PXI Digital Pattern Instrument
786320-01
1-Slot, 100 MVector/s PXI Digital Pattern Instrument - The PXIe‑6571 is designed for semiconductor characterization and production test. It includes the Digital Pattern Editor for configuring pin maps, specifications, levels, timing, and patterns. It also includes debugging tools … like Shmoo, digital scope, and viewers for history RAM, pin states, and system status. The PXIe-6571 requires a chassis with 82 W slot cooling capacity, such as the PXIe-1095.
-
product
PCMCIA Card
DAS-429PCMCIA/RT10
Both cards contain 68 Kbytes of true dual-port RAM, for data blocks, control registers and Look-up table, mapped within the Common Memory space. The card also contains a FLASH-based Card Information Structure (CIS) within the Attribute Memory space.The cards comply with the Personal Computer Memory Card International Association (PCMCIA Release 2.1) standard, including Plug and Play. The card's small size and suitability for PCMCIA compatible notebook computers with Type II and Type III slots make it a complete solution for developing and testing ARINC-429 interfaces and for performing system simulation of the ARINC-429 bus, both in the lab and in the field.The cards are supplied with C drivers, including source code, Mystic Windows software and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application.
-
product
PCIe-Mini
PCIe-Mini-DA4
The PCIe-Mini-DA4 is a PCiexpress Mini board with a total of 4 voltage outputs D/A. Each output is followed by a buffer able to provide +/- 30 mA. Special function code allows global updates of all channels or by a group of eight channels at atime. Standard ping-pong output registers for each channel or optional data RAM allows waveform generation with minimum processor involvement.
-
product
8 SE Or 4 Diff. Input Channels, 4 Analog Output Channels, PCI Express
APCIE-3121-8-4
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
product
Memory Diagnostic Utility
MemTest86
MemTest86 is the original, free, stand alone memory testing software for x86 computers. MemTest86 boots from a USB flash drive or CD and tests the RAM in your computer for faults using a series of comprehensive algorithms and test patterns.
-
product
Low-power, High-performance FPGA
iCE40 LP/HX
*Available in three series with LUTs ranging from 384 to 7680: Low power (LP) and high performance (HX)*Integrated hard I2C and SPI cores that enable flexible device configuration through SPI*Match your preferred display to your application processor with interfaces such as RGB, 7:1 LVDS and MIPI DPI/DBI*Multi-source your image sensors by implementing flexible bridges supporting common interfaces such as HiSPi, subLVDS, LVDS and Parallel LVCMOS*Up to 128 kbits sysMEM™ Embedded Block RAM*Industry’s broadest range of 0.35 mm - 0.40 mm pitch BGAs fit in space-constrained applications
-
product
Interface Module for the Multimode, Multiprotocol Excalibur 400 Family of Carrier Boards
M4K1553Px(S)
The M4K1553Px(S) interface module for the multimode, multiprotocol, Excalibur 4000 family of carrier boards provide a complete solution for developing and testing 1553 interfaces and performing system simulation of the MIL-STD-1553 bus. The module handles all standard variations of the MIL-STD-1553 protocol.Each M4K1553Px multi function module contains 64K bytes of dual-port RAM for Data blocks, Control registers, and Look-up Tables. All Data blocks and Control registers are memory mapped, and may be accessed in real time. Each of the independent dual redundant M4K1553Px modules may be programmed to operate in one of three modes of operation: Remote Terminal, Bus Controller/Concurrent-RT, and Bus Monitor. In addition, modules 1 and 3 can be programmed to operate as Concurrent monitors, to modules 0 and 2 respectively.Each M4K1553PxS single function (RT validated) module operates either as a Bus Controller, Remote Terminal, or Bus Monitor.
-
product
Intelligent Mini Munitions Store Interface (MMSI) Module for Excalibur 800 Family of Carrier Boards
M8KMMSI
The M8KMMSI is an intelligent, Mini Munitions Store Interface [MMSI] module for the multimode, multiprotocol, Excalibur 8000 family of carrier boards. Each module of the M8KMMSI contains 64K bytes of dual-port RAM for Data blocks, Control registers, and Look-up Tables. All Data blocks and Control registers are memory mapped and may be accessed in real time. Each M8KMMSI module may be programmed to operate in one of three modes of operation: Remote Terminal, Bus Controller/Concurrent-RT/Concurrent Monitor and Bus Monitor.The M4KMMSI comes complete with Windows software, a C-driver software library including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application.
-
product
Interface
RAR15X
Featuring high-level API for Microsoft® Windows® 7, 8, 8.1, 10, Server 2008 and Server 2012 R1/R2 (32 and 64 bit), Linux®, Integrity, and VxWorks® that reduces application development time, standard features of the RAR15X include 8 Mbytes of RAM and 64-bit message time tagging.
