High-Speed Digital I/O
-
product
USB-6509, 96-Channel, 5 V, TTL/CMOS, 24 mA, USB Digital I/O Device
779975-01
The USB-6509 is an industrial, bus-powered USB device that can directly drive external digital devices such as solid-state relays (SSRs). You can configure each port for input or output, and no external power supply is … required for outputs. Using programmable power-up states, you can configure the initial output states in software to ensure glitch-free, safe operations when connected to industrial actuators. If a computer or application fault occurs, the USB-6509 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
product
Handheld Digital Multimeter, 3½ Digit
U1233A
Ergonomic shaped 6K counts DMM with flashlight, low input Z mode, non-contact voltage detection & continuity visual/audio alerts. Keysight Remote Link Solution enabled.
-
product
PCI-4065, 6½-Digit, ±300 V, PCI Digital Multimeter Device
779770-01
The PCI‑4065 makes AC/DC voltage, AC/DC current, and 2‑ or 4‑wire resistance measurements, as well as diode tests. It is ideally suited for OEMs, educational laboratories, or other cost-conscious test and measurement applications.
-
product
Digital Module For Remote I/O
Digital Modules for Remote I/O provide 24 V digital inputs or outputs and offer 1‐, 2‐, 3‐, and 4‐wire spring terminal connection options. You can use inputs as counters or standard digital inputs, and you can adjust filter time to improve measurement quality. Inputs can include a built‐in power supply for sensors. Output modules feature circuit and overload protection and can drive up to 500 mA per channel, up to 8 A per module.A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the Digital Module for Remote I/O from a NI real‐time controller. You can use remote I/O hardware to add low‐cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high‐speed or specialty measurements.
-
product
Handheld Digital Multimeter, 4 digit, Water and Dust Resistant
U1271A
Feature sets that meet traditional industrial requirements and improve productivity and safety Improved accuracy and resolution to meet traditional industrial requirements (30,000 counts resolution with 0.7% for ACV accuracy)Intelligent features to improve productivity and safety (selectable Low Pass Filter LPF and quick signal type identification Qik-V)Better grip Both visual and audible continuity indication in noisy environments Easy access to fuse for simplified maintenance Easy connectivity to PC and internal memory (up to 200) for data logging Large rotary switch and buttons that are easy to operate Dust and water resistant casing (IP 54 compliant)Compatible with U1177A/U1117A IR-Bluetooth adapter for remote monitoring & datalogging Altitude: 3000 meters
-
product
Digital Cable
The Digital Cable models include a variety of industry-standard front- and back-end connectors, such as 68-pin VHDCI, 68-pin D-SUB, and flying lead options. Some models can connect digital instruments with other accessories to break out cable signals for direct access. Others provide flying leads that plug directly into any 0.1 in. header connector.
-
product
Configurable 6U VME Multifunction I/O Boards
NAI offers a variety of rugged 6U VME I/O boards – designed to be combined with our pre-integrated smart function modules – to create a highly flexible COTS-based solution ideally suited for I/O intensive sense, response and communications requirements operating over VME Bus.
-
product
Ethernet/LXI digitizerNETBOX 8 Bit High Speed Digitizer - 1.25 GS/s, 500 MHz Bandwidth
DN2.221-04
The digitizerNETBOX DN2.22x series allows recording of up to 8 channels with sampling rates of 5 GS/s and a bandwidth of 1.5 GHz. These Ethernet Remote instruments offer outstanding A/D features both in bandwidth and signal quality. The combination of high sampling rate and resolution makes these digitizers the top-of-the-range for applications that require high speed signal acquisition. The digitizerNETBOX can be installed anywhere in the company LAN and can be remotley controlled from a host PC.
-
product
Dynamic Digital I/O (3U), 32 Channels Up To 100 MHz W/256MB On-Board Memory, W/LVDS
GX5282
The GX5280 Series are high performance, cost-effective 3U PXI dynamic digital I/O boards with 32 TTL input or output channels and 32 LVDS input or output channels. The GX5280 Series offers an industry leading 512 MB of on-board memory and supports test rates up to 200 MHz. The single board design supports both master and slave functionality without the use of add-on modules.
-
product
USB-7845, Kintex-7 70T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device
783200-01
Kintex-7 70T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device - The USB‑7845 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The USB‑7845 features a dedicated A/D converter per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical DAQ hardware.
-
product
SHC68-C68-RDIO2, 68-Pin VHDCI Male to 68-Pin VHDCI Male, 80 MHz, Shielded Digital Cable, 1m
156166-01
SHC68-C68-RDIO2 Shielded R Series High Speed Digital Male VHDCI Cable, 1m
-
product
ISA Digital IO Board
MS 1804
*Discrete Input / Output 48 Channels*TTL Pulse measurement channels (Timers / Counters) 12 Channels*TTL Pulse Generation 12 Channels*Bi-directional Bus 16 Bit*The Pulse Generation Frequency from 10Hz to 40MHz*The no. of pulses controlled from 1 to 255 pulses*All Channels are compatible with 5V TTL / CMOS*All the pulse input and the output signals and Bi-directional write signals driven through Pin Driver*Standard ISA Bus Interface*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
product
64-CH Isolated Digital I/O PCI Cards
PCI-7432/7433/7434
ADLINK's cPCI/PCI-743X series cards are 64-CH high-density digital input and/or output cards that provide a robust 2,500 V isolation protection and are suitable for most industrial applications. The wide input range of the cPCI/PCI-7432 and cPCI/PCI-7433 makes it easy to sense the status of external devices. There are several options for PCI-743X series, such as normal version with input range from 0 to 24 V, as well as HIR version with high input range from 0 to 50 V. The PCI- 7433ALC is specifically designed for AC power test system.
-
product
USB-6349, 32 AI (16-Bit, 500 kS/s), 2 AO (900 kS/s), 24 DIO USB Multifunction I/O Device
785816-01
32 AI (16-Bit, 500 kS/s), 2 AO (900 kS/s), 24 DIO USB Multifunction I/O Device - The USB-6349 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB-6349 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
product
Digital I/O
With digital I/O cards, static or dynamic bit patterns can be generated or recorded. Each bit is assigned a control signal for an output and a sensor signal for an input. The usual voltage range for the inputs and outputs is between 2 V (TTL) and 24 V (automation).
-
product
PXIe-5622, 150 MS/s, 16-Bit PXI IF Digitizer
780412-01
150 MS/s, 16-Bit PXI IF Digitizer—The PXIe‑5622 includes onboard signal processing (OSP), which enables features such as quadrature digital downconversion (DDC), real DDC, and anti-alias filtering. The PXIe‑5622 is ideal for communications applications because of its high dynamic range front end and a high-throughput PXI Express interface that allows it to stream IF data to disk for hours at the full sample rate.
-
product
PCIe 8 Bit High Speed Digitizer - 2.5 GH/s on 2 Channels, 1.5 GHz Bandwidth
M4I.2221-X8
The 9 models of the M4i.22xx-x8 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
product
PXI-6515, 64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Sink Outputs, Bank-Isolated PXI Digital I/O Module
778964-01
64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Sink Outputs, Bank-Isolated PXI Digital I/O Module—The PXI‑6515 is an industrial digital I/O interface with eight banks of isolated channels. You can wire each input bank in a source or sink configuration. With programmable power-up states, you can configure the initial output states in software to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PXI‑6515 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
product
PXI-6529, 48-Channel, Sink/Source Inputs, Channel-Channel Isolated PXI Digital I/O Module
779949-01
48-Channel, Sink/Source Inputs, Channel-Channel Isolated PXI Digital I/O Module—The PXI‑6529 is an industrial, parallel digital input interface. PXI‑6529 devices are ideal for a variety of applications from automotive design, industrial factory automation, and machine control to aerospace, laboratory research, and biomedical applications. With programmable power-up states, you can configure the initial output states in software to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PXI‑6529 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
product
High-Speed Digital Bus Test Instruments
Teradyne and AIT instruments test legacy and newer digital buses.The enormous variety of digital buses used in defense and aerospace applications requires comprehensive, yet efficient testing.Teradyne and AIT COTS instruments meet these challenging bus test requirements for legacy and standardized buses, as well as evolving digital buses that have faster speeds, larger data volumes, and increasingly complex protocols requiring real-time test and emulation.
-
product
PCIe-5764 , 16-Bit, 1 GS/s, 4-Channel PCI FlexRIO Digitizer Device
785962-01
The PCIe-5764 is a PCI FlexRIO Digitizer Device that simultaneously samples four channels at 1 GS/s with 16 bits of resolution and features 400 MHz of analog input bandwidth. With up to 70 dB of SNR, the PCIe-5764 is ideal for applications that require a wide dynamic range with a wideband digitizer.
-
product
PC-based DSP Systems with Analog I/O - Ultra High-Speed
PCI, cPCI / PXI : 32 / 64 bit, 33MHz600MHz 6416 DSPFPGA Virtex-II, 1.5 to 6M gatesZBT SBSRAM, 32MB SDRAMExtreme performanceFPGA development supported
-
product
224 Channel Digital I/O Modular PXI Card
GX5731
The GX5731 is a 6U modular digital I/O card with 224 I/O channels. Designed for ATE, data acquisition, or process control systems where a large number of discrete I/O channels are required, the GX5731 offers the highest density in the industry for a single PXI plug-in board. Of the 224 channels, 128 support TTL levels with the direction of each group of eight channels programmable as input or output. The other 96 channels can be used for customized I/O using MTS' GX57xx series I/O modules.
-
product
SH68-68-D1, Shielded Cable, 2 m
183432-02
68-Pin, Female D-SUB to 68-Pin, Female D-SUB, Twisted Pair, Shielded Digital Cable - The SH68-68-D1 Digital Cable connects NI 6533/4 digital instruments and NI 660x or 661x counter/timer modules to 68-pin accessories. This shielded cable features twisted pairing and is offered in different lengths.
-
product
High Speed PXIe Digital IO Card - 32 Channels, Extendable up to 256 Channels in One Chassis
Model 33010
Chroma 33010 is a high-density 100MHz PXIe digital IO card designed for characterizing, validating, and testing a variety of digital and mixed-signal ICs. Each IO Card consists of a Sequencer Pattern Generator (SQPG) and 32 Channels of fill ATE-like features. The 33010 IO card is expandable up to 356 channels. Some unique features of the 33010 include an on-board SQPG, per pin timing/levels/PMU/TFMU, multiple time domains, and multithreaded testing for complex IC testing. Each channel is also equipped with 64M vector memory, 16 timing sets with on-the-fly timing change, and per pin timing and frequency measurements up to 400 MHz.
-
product
USB-6363, 32 AI (16-Bit, 2 MS/s), 4 AO (2.86 MS/s), 48 DIO USB Multifunction I/O Device
782257-01
32 AI (16-Bit, 2 MS/s), 4 AO (2.86 MS/s), 48 DIO USB Multifunction I/O Device - The USB‑6363 offers analog I/O, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB‑6363 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
product
High-Speed Digitizers and Multichannel DAQ Solutions
With our high-speed digitizers, we improve your measurement fidelity, signal integrity and measurement throughput, keeping low the total cost of ownership. The entire range includes PCIe, PXIe and AXIe form factors, configurable in single to multichannel solutions. Our products cover several applications in commercial OEM, aerospace & defense, wireless & RF communication and high-energy physics.
-
product
Analog & Digital I/O Modules
USB analog and digital I/O modules are a complete family of data acquisition modules for use in process control systems. The analog input modules can measure process signals such as DC voltage, thermocouples, 4-20mA current loops, discrete contact closures.
-
product
NI-9402, LVTTL, 4 Bidirectional Channels, 55 ns C Series Digital Module
779987-01
LVTTL, 4 Bidirectional Channels, 55 ns C Series Digital Module - The NI‑9402 is a per‑channel configurable digital I/O interface for input or output. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the NI‑9402 for … implementing custom, high-speed counter/timers; digital communication protocols; pulse generation; and more. Each channel features transient isolation between the I/O channels and the backplane.
-
product
NI-9401, 5 V/TTL, 8 Bidirectional Channels, 100 ns C Series Digital Module
779351-01
5 V/TTL, 8 Bidirectional Channels, 100 ns C Series Digital Module - The NI‑9401 is a configurable digital I/O interface for input or output in 4‑bit increments. Therefore, the NI‑9401 can create three configurations: 8 digital inputs, 8 digital outputs, or four digital inputs and four digital outputs. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the NI‑9401 for implementing custom, high-speed counter/timers; digital communication protocols; pulse generation; and more. Each channel features transient isolation between the I/O channels and the backplane.
