Filter Results By:
Products
Applications
Manufacturers
-
product
Trailer Light Testers
Pro-Check 725
Pro-Check trailer light testers with advanced electrical diagnostics are rugged, lightweight, and economical. They independently test each electrical circuit on a trailer to ensure proper connectivity. The Pro-Check identifies each specific type of electrical wiring fault. Lite-Check’s patented active diagnostic system takes the guesswork out of identifying trailer light and electrical problems. The Pro-Check commercial trailer light tester with electrical circuit diagnostics, not only identifies faults, but the specific circuit the fault is on. Faults are identified as “Open Circuit”, “Open Ground”, “Short” (w/all circuits identified), or “Chassis Ground”. Audible alarms alert technicians to found electrical faults.
-
product
Leakage Current Tester and Clamp-On Earth / Ground Resistance Tester
10µA Ultra High ResolutionLarge Conductor Diameter (30mm)AC Current in 5 Ranges (40mA, 400mA, 4A, 40A, 60A)Wide Frequency Response (40Hz-1KHz)ACA, ACV, Ω and ContinuityLarge 3¾ Digit LCD (4000 Count)40 Segment Fast Bargraph Display (20 times/sec.)Data Hold and Max / Min HoldRelative Measurement600 Vrms Overload Protection in Resistance Range
-
product
Lan Cable Tester
185 LCT
Standard Electric Works Co., Ltd
● Designed for RJ45/RJ11 modular cables, 10/100 base-T cable and Token Ring cable.● The LAN cable tester can verify cable continuity, open, short circuit and miss-wired.● The remote receiving unit is available for installed cables far away either on the wall plates or on the patch panels.● Auto and manual scan functions.● Ground wire test. ● Lock status function.● Buzzer sound warning for wire status.● Display : LED indication for wire status.
-
product
Signature Surge Testers
TS Model
Although all PJ Surge Testers are capable of testing 3 Phase Motors, this "TS" Model has the same characteristics as the Signature Model (rack-mounted, Tektronix TDS1002, 1 Billion Samples/sec, real time, programmable, storage oscilloscope) but includes a built-in 3 phase test selector switch that facilitates 3 phase motor testing by mechanically re-positioning the ground terminal.
-
product
Digital LOOP/PSC/EARTH Tester
1824 LP
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Measures Earth Resistance without the need for poles in the ground or external measuring wires.● Earth measurement uses the real earth current path and the current generated by the electric network, without the need for any disconnection.● The Earth Resistance displayed is exactly the earth resistance that the earth current will need to go through if an earth fault occurs. (you do not need to add all the bonding points and connection paths)● Displays voltage supply at the transformer(Line to Neutral), without loading the transformer.● Single one smart push button operation; ON, Scroll through results and menus.● Checks wiring integrity (LEDs).● Auto-off / Auto-ranging (software range).● Color-coded test leads.● Combined prospective short circuit current, loop, and earth tester.● Loop test for L-E and PSC between L-N.● Voltage test L-N.● Display can be customized for large orders.
-
product
Ground Resistivity and EarthService Tester
AD-510
Large, readable LCD display (2000 counts), Instant battery life indicator, Test frequency: 128 Hz (quartz generator), Test Voltage: max 30 V peak-to-peak, Range: 0,01 W ? 2 k W. Accuracy resistance measurement: 1 % 2 digits,
-
product
Digital Ior Leakage Current Clamp Tester
MCL-400IR+
MULTI MEASURING INSTRUMENTS Co., Ltd.
・About Ior Leakage CurrentRecently, the leakage current clamp meter is widely used for insulation control of low voltage circuit as the supplementary method of the insulation resistance measurement. The control of leakage current has the advantages to enable the prediction of insulation condition in the electrical power line without having to shut off the power. The leakage current (Io) includes the capacitive leakage current (Ioc)originated in the capacitance and the resistive leakage current (Ior) originated in the insulation resistance each related to the ground. It is considered that the measurement of resistive leakage current (Ior) is the very useful and effective method for the insulation control of low voltage circuit. However, it was difficult to measure the resistive leakage current (Ior)with traditional leakage current clamp meter. MCL-400IR new digital clamp tester enabled the measurements of the resistive leakage current (Ior)without voltage input(phase detection).
-
product
Earth Ground Test Lead Kit
TL-796
*Earth Resistance Test Lead Kit*For use with IDEAL 61-796 3-Pole Ground Resistance Tester
-
product
Digital Electrical Network Analyzer
1826 NA
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Measures Earth Resistance without the need for poles in the ground or external measuring wires.● Earth measurement uses the real earth current path and the current generated by the electric network, without the need for any disconnection.● The Earth Resistance displayed is exactly the earth resistance that the earth current will need to go through if an earth fault occurs. No need to add all the bonding points and connection paths resistances.● Displays voltage supply at the transformer (Line to Neutral), without loading the transformer. Displays voltage between Line (Phase) and Earth (Ground), without drawing any current.● Measures the impedance of the line itself so you can analyze and differentiate between the multiples paths of the wiring.● Measures the Neutral Impedance. Single one smart push button operation; ON, Test, Scroll trough results and menus.● Checks wiring integrity (LEDs).● Auto off/auto ranging (software ranging). ● Combined prospective short circuit current, loop, individual wire and Earth Tester.● Voltage test L-N and L-E.● Loop test for L-E and L-N and PSC.● Enables analysis of constituent components in L-E and L-N loops giving resistance of earth, neutral wire, live wire and transformer winding.● Display can be customized for large orders.
-
product
Earth Resistance Tester
2678
Shenzhen Chuangxin Instruments Co., Ltd.
RK2678 series Earth Resistance Tester is used to measure the grounding resistance of the electrical equipments’ internal. It’s suitable for measuring the ground wire resistance of the various motors, electrical appliances, instruments and meters, household appliances and other equipment enclosure etc.
-
product
Ground Bond Tester
264
Our 264 Model makes Ground Bond / High Continuity Testing simple with 40 Amps of current to satisfy your NRTL standard. With an intuitive interface that allows you to set-up a test in seconds and practical security settings, our 264 can easily be deployed in both laboratory and production line environments. Ensure every Ground Bond Test is accurate with our Milliohm offset function.
-
product
AC Hipot Tester
295
Our Model 295 is a simple-to-use AC Hipot Tester with the built-in ability to test Ground Continuity (Low Current Continuity). You need a Hipot Tester that includes all the features you need to get the job done, the 295 has what you're looking for. Make testing simple with common sense security settings. PLC Remote allows you to make AC Hipot Testing safer with Personal Protective Equipment (PPE).
-
product
"Handy Hooker" Circuit Tester
25600
Small size allows easy use even in the tightest places. Quickly test low voltage up to 12 volts. Alligator clip grounds tester.
-
product
Ground Earth Resistance Tester
2678X
Shenzhen Chuangxin Instruments Co., Ltd.
Ground Earth Resistance Tester verifies the integrity (continuity) of the protective bonding of the equipment (Class I equipment) designed to secure safety through the basic insulation and protective earthing. It is also called earth (ground) bonding test. If the continuity of the protective bonding is confirmed, we can conclude that the equipment has the requirements for preventing electric shock even if the insulation between the primary circuit and the accessible conductive section fails and a fault current flows through the distribution system.
-
product
DC Hipot Tester
296
Our Model 296 is a simple-to-use Hipot Tester with the built-in ability to easily test Ground Continuity (Low Current Continuity). The 296 is capable of performing Hipot Tests in both AC & DC currents. You need a Hipot Tester that includes all the features you need to get the job done, the 296 has what you're looking for Make testing simple with common sense security settings.
-
product
AC Ground Bond Tester
446
Our 446 model is a 4-in-1 tester with AC Hipot, DC Hipot, Insulation Resistance, and Ground Bond capabilities. This tester features a simple design and easy-to-use interface, reducing setup time and increasing production-line throughput for your application. The 446 is equipped with multiple memories and an optional USB port for remote BUS communication so you can quickly perform tests on a variety of DUTs from the front panel or with a PC. Add to user safety by equipping your tester with Personal Protective Equipment (PPE) via the built-in safety interlock.
-
-
product
Ground Network Earth Resistance Tester
HTDW-5A / 736
Wuhan Huatian Electric Power Automation Co., Ltd.
It is suitable for the test of grounding resistance of large power grid in power departments, substations and other institutions.
-
product
Surface Resistance Meter Kit - Test Anti-Static, Static Dissipative and Conductive Surfaces
PRS-812RM
- Surface Resistance Tester from 0.10 Ω to 1 Teraohm- Constant Voltages 10 volts and 100 volts- Automatic Electrification Period- Determines if a surface is Dissipative, Conductive, or Insulative- Measures resistance point-to-point(Rtt) and resistance to ground (Rtg)- Measures resistance of ESD Flooring, ESD Worksurfaces and Packaging- Conforms to all ESD Association Standards for Resistive Characterization- Includes 2 each Surface Resistance Probes- Packaged in a hard shell Carrying Case- Certificate of Calibration Traceable to NIST included- 2-year Limited Warranty on Main Instrument
-
product
DC12V Heavy Duty Circuit Tester
TE6-0706
Hangzhou Tonny Electric & Tools Co., Ltd.
*Heavy Duty probe *Heavy plastic handle and insulated ground clip*Testers light up and/or buzz to indicate testing result*Lights for easy visibility.*Heavy duty coil cord or straight cord (optional).*Durably designed for a long service life*For testing 6-12 volt systems for wire breaks, shorts, fuses, lamps, relays, armatures and more.*Suite able for a broad range of household, car, trucks, boats, trailers, vans, motorcycles, industrial and commercial uses.
-
product
HBM Verification Tester
HBM-VT
High Power Pulse Instruments GmbH
- HBM pulse generator verification tester according ANSI/ESDA/JEDEC JS-001 up to ±10kV- To be used in HBM test and qualification labs for regular pulse generator specification compliance test in order to fulfill lab audit and certification requirements- Fully automatic compliance test and verification of HBM pulse generators regarding ANSI/ESDA/JEDEC JS-001 normative standard at 3 different load conditions: Short Circuit, 500 Ω, and a reference diode at VBR=15 V reverse breakdown voltage, including DC test- Parameter evaluation and verification of the transient HBM current waveforms: Peak Current, Rise Time, Decay Time, Maximum Ringing Current- Optionally available upgrade for all HPPI TLP-3010C, 4010C, 8010A, 8010C, HBM-TS10-A hardware systems in combination with HBM-S1-B (6kV) pulse generators (upgrade on request)- Fully automatic test report generation (PDF)- Electrically floating (no fixed system ground): The HBM loads, current sensor output, USB control interface and the enclosure are electrically floating. There is no limiting system ground which may introduce common-mode interference induced HBM current measurement errors.- Isolated industrial full-speed USB control interface- Isolated power supply derived from USB port- Compact size 126mm x 82.5mm x 44.5mm
-
product
Battery-Powered Bounding Tester
MRC 100S–BD-3
The MRC 100S-BD-3 Bounding Tester is a battery-powered portable digital ohmmeter, which can be used, for example, for testing the ground connection in any section of an aircraft using different measuring currents (up to 10A). This high current ensures that any uncertain connections are recognised.
-
product
12-24V Multi-functional Auto Tester With LCD Display
6511A
Peaceful Thriving Enterprise Co Ltd
Test the automotive electrical system within 12-24V. In order to save the testing hours for the automotive electrical system, the tester is designed to test the system without re-connection between the vehicle battery and the testing components. For the testing and safety purpose, the tester contains short-circuit protection, which can also check the ground connection without voltage drop test. The short-circuit protection system contains the recoverable fuse, so the technician will not waste the fuses during the testing. The extension cable is long enough for a technician to test the whole system for the vehicle. Therefore, the technicians do not have to search for ground connection constantly.
-
product
Ground Resistance Inspection Box
AllWin Instrument Science and Technology Co., Ltd.
Check the ground resistance tester each time prior to start work everyday morning and do some relevant records.
-
product
Automated Digital Ground Continuity Tester
Educated Design & Development, Inc.
1 Button Testing - No setup required, just plug right in!Digital LED display reads out in OhmsAlso performs the Low Current Ground Continuity test, at the same time!Auto Test Time (1 sec. / 60 sec.)+ - No need to set a timer or clock watchCustom universal receptacle accepts both 120V and 240V plugs.Zero feature allows you to "zero-out" the test lead impedance.Meets UL, CSA, CE, EN, IEC, MIL and all other international safety agency requirements.
-
product
Heavy Duty Ranger Mutt
TT9102
Commercial trailer light and electric brakes tester that reduces guesswork and saves time by powering each trailer electrical circuit in 7-way round pin arrangements. Allows for proper verification of wiring configuration, ground integrity, short circuit and overload conditions, along with electric brake operation and turn signal simulation.
-
product
Cable Tracer and Digital Multimeter
187 MCT
Standard Electric Works Co., Ltd
Lan Cable Tester● Designed for RJ45/RJ11 modular cables, 10/100 base-T cable and Token Ring cable etc.● The LAN cable tester can verify cable continuity, open, circuit and miss-wired. ● The remote receiving unit is available for installed cables far away either on the wall plates or on the patch panels.● Auto and manual scan function.● Ground wire test.● Display : LED indication for wire status.Digital Multimeter● 4000 counts LCD.● Full automatic measurement. Voltage measurement. Resistor measurement.● Range change function.● Select function.● Data Hold function.● Continuity check.● Diode measurement.● Low battery indication.● Input impedance:10MΩ.
-
product
Surge with 3 Phase Transfer Switch Consoles
TC Model
(Surge with 3 Phase Transfer Switch Consoles) Although all PJ Surge Testers are capable of testing 3 Phase Motors, this "TC" Model has the same characteristics as the "C" Model, but includes a Built-in 3 Phase Test Selector Switch that facilitates 3 phase motor testing by mechanically re-positioning the ground terminal.
-
product
AC Ground Bond Testers
440 Series
The 440 Series provides advanced 4-in-1 test capability in a convenient one-box solution. This new series performs AC Hipot (448 - 500 VA), DC Hipot, Insulation Resistance and 40A AC Ground Bond tests while taking up minimal production line space. The 440 Series is simple and easy-to-use; reducing setup time and increasing production line throughput for your application. With multiple memories and an optional USB port for remote BUS communication so you can quickly perform tests on a variety of DUTs from the front panel or with a PC. Learn about our 5 Year Warranty.
-
