-
Product
Single 16 to 1 Terminated 50 600MHz PXI RF Multiplexer
40-765-001
Multiplexer Module
This 4 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
Product
Resistive & Capacitive AC Load Bank
RCD
-
RCD AC load banks are used to test the REAL working condition of UPS, rectifier, inverter and etc who are loaded by non-linear or electronic load with non-constant resistance such as computer, networking equipments and etc. Through the accurate detection of its output and power quality, users could avoid the inadequate loading capacity or cause pollution to power grid, so as to guarantee supply security. JUNXY RCD load banks leading power factor loads are created to debug power supply system parameters such as its crest factor test.
-
Product
DC Electronic Loads
-
Electronic Test & Power Systems
An adjustable electronic load gives the test engineer the ability to qualify designs, check production batches or service and repair electrical products. Many applications demand an adjustable electronic load. These include the burn-in of new devices along with general power supply, battery, fuel cell and generator testing.
-
Product
GMCT 26-Pin RF Cable Assembly, 75Ω, Male To Unterminated, 1m, RG179 Cable
40-979-726-1m-FU
RF Cable Assembly
This 1m long cable assembly is part of a range of cables suitable for applications using the Positronic 26-pin GMCT 75Ω RF connector. It is constructed from RG179 silver plated copper clad steel cable with FEP insulation and a bandwidth of 500MHz. Screwlocks are provided to secure the connector to the associated product.
-
Product
PXI/PXIe RF Multiplexer, Quad 4-Channel, Terminated, 8GHz, 50Ω, SMA
42-882B-004
Multiplexer Module
This multiplexer has low VSWR characteristically over the full operating frequency range and consistent insertion loss characteristics. The use of solid state switches ensures a long service life with no wear out mechanism, making the 40/42-882B MUX ideal for ATE systems requiring frequent and fast operating RF switching.
-
Product
RF Adapters
SMPM Adapters
-
a type of blind-mate, push-on connector that is similar to SMP connectors.
-
Product
PXI/PXIe RF Matrix, 32x4, 300 MHz, 50 Ω, SMB
42-724-022
Matrix Switch Module
The 40-724-022 (PXI) and 42-724-022 (PXIe) are 32x4 RF matrix modules suitable for switching frequencies up to 300 MHz. Having a 50 Ω characteristic impedance and front panel SMB connectors, these modules provide a simple and scalable bidirectional matrix for RF and are intended for the easy construction of high performance switching systems.
-
Product
RF Testing & Engineering Services
RF Testing & Engineering Services
-
Our team has world-class radio frequency experience in defense contracting, design, engineering, manufacturing, quality, research, and testing. The staff at 360°RF includes numerous design patent holders, a sitting member of the CEA's (Consumer Electronics Assoc.) Standards Committee, as well as columnists, editors, and authors for trade publications and reference books, including Radio Shack, Antennas, Selection, Installation, and Projects, TV, FM, CB, Cellular, Satellite, and Shortwave.
-
Product
Battery Load Tester
BT-100
-
Schumacher Electric Corporation
FOR EVERYDAY DIY USEEasy to operateTest load, battery condition, starter motor draw and complete charging system diagnosis.Works on 6 and 12 volt batteries50 amp load test for 6 volt batteries100 amp load test for 12 volt batteries Tests 6 and 12 volt batteries ─ up to 1000 CCATop-mounted rocker switch for easier operationSuper-grip, heavy-duty color-coded battery clampsEasy-to-read meter ─ accurate and shock resistantBaked enamel, steel case ─ ventilated to keep coolRubber insulated carrying handle ─ for comfort and safety
-
Product
RF Power Splitter, Combiner, Divider
PD2360
-
INSTOCK Wireless Components, Inc
Wideband Frequency (350 - 1000 MHz)Low Insertion Loss (0.4 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.2 : 1 avg)RoHS Compliant Splitter ConstructionTri Alloy Type N Female (Jack) Low PIM
-
Product
CMX RF Port Extender
CMX-Z25
-
Complex devices under test (DUT) come with additional antenna ports to support low, mid and high bands - and advanced MIMO schemes such as 4x4 MIMO. The R&S®CMX-Z25 is the solution: Up to 16 DUT ports can be supported with just 4 ports from R&S®CMX500. So even prototypes of 5G smartphones, tablets, laptops or industrial modules with an extended number of antenna ports can now be connected to a single R&S®CMX500. Together with the scalable CMX architecture any 5G and 5G Advanced mobile device can now be tested in one go - without recabling or 3GPP band combo limitations.
-
Product
High-Power Directional RF Wattmeters
81300-A Series
-
The 81300-A series of High-Power Directional RF Wattmeters are designed to measure RF power in 50-Ohm 3-1/8 inch coaxial transmission lines. To use the Wattmeter, simply connect it between the transmitter and antenna or dummy load and plug in the appropriate measuring element.
-
Product
PXI/PXIe RF Matrix, 16x2, 300 MHz, 50 Ω SMB With Loop-thru
42-728A-001-L
Matrix Switch Module
The 40-728A-001-L (PXI) and 42-728A-001-L (PXIe) are 16x2 50 Ω RF matrices with SMB connectors and Y-axis loop-thru. The 4x-727A/728A/729A range are high density RF matrix modules suitable for switching up to 300 MHz in 50 Ω or 100 MHz in 75 Ω. They are available in 50 Ω or 75 Ω versions with SMB connectors or in 50 Ω versions with a multiway connector.
-
Product
RF Technology And Design
-
RF technology is key to many aspects of electronics these days. With many systems from cellular to other wireless technologies including, Wi-Fi, WiMAX, NFC, RFID, and many other systems using RF signals.
-
Product
PXIe-254, 6.6 GHz, 50 Ω, Solid-State, Dual 4x1 PXI RF Multiplexer Switch Module
780587-43
Multiplexer Module
PXIe, 6.6 GHz, 50 Ω, Solid-State, Dual 4x1 PXI RF Multiplexer Switch Module—The PXIe‑2543 features high-performance solid-state relays that offer unique benefits such as unlimited relay life and fast switching time. Front-mounted SMA connectors provide easy connection to your RF devices, and the module features termination on every COM line and channel.
-
Product
RF Switch
-
RF switches are components used for switching the signal paths of high frequency circuits in wireless communication devices.
-
Product
PXI Quad 4 to 1 RF Multiplexer 3GHz 50 Ohm SMB
40-872-004
Multiplexer Module
The 40-872-004 is a 50 Ohm 4 to 1 RF MUX available with 4 banks in a single PXI slot. It exhibits low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The injection of noise and unwanted signals into the signal paths of the 40-872 has been minimized by careful attention to the mechanical and electrical design.
-
Product
L-Band RF Tuner and 4-Channel 200 MHz A/D with Virtex-6 FPGA - 6U VPX
Model 58690
-
- Two L-Band tuners accept RF signals from 925 MHz to 2175 MHz- Two programmable LNAs boost LNB (low-noise block) antenna signal levels with up to 60 dB gain- Two programmable analog downconverters provide I + Q baseband signals with bandwidths ranging from 4 to 40 MHz- Four 200 MHz 16-bit A/Ds- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Up to 4 GB of DDR3 SDRAM; or: 64 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
FieldFox Handheld RF Analyzer, 6.5 GHz
N9914A
-
6.5 GHz max frequency Carry the world's most integrated handheld RF analyzer: standard model includes cable and antenna analyzer Expand capabilities with optional VNA, spectrum analyzer, built-in power meter, vector voltmeter, and more Save time by measuring DTF and TDR in the same sweep Simultaneously measure all four S-parameters Make accurate spectrum analyzer measurements ( 0.5 dB) without needing warm-up Calibrate simply with QuickCal
-
Product
L-Band RF Tuner and 2-Channel 400 MHz A/D with Kintex UltraScale FPGA - 3U VPX
Model 54891
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Accepts RF signals from 925 MHz to 2175 MHz- Programmable LNA handles L-Band input signal levels from -50 dBm to + 10 dBm- Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz- Two 400 MHz 12-bit A/Ds digitize IF or I+Q signals synchronously- Two FPGA-based multiband DDCs (digital downconverters)- Xilinx® Kintex® UltraScale™ FPGA- Five GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- PCI Express interface (Gen. 1, 2 & 3) up to x8- Clock/sync bus for multimodule synchronization- Optional LVDS and gigabit serial connections for FPGA for custom I/O- Optional optical interface for data streaming- Navigator BSP® for software development- Navigator FDK® for custom IP development- Spark® fully-integrated development system- Free lifetime applications support- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
12V 0-500 Amp Carbon Pile Battery Load Tester and 12/24V Electrical Systems Tester
6042
-
• Test batteries up to 1000 CCA• Interprets data from the charging/starting system on easy-to-read LCD displays• Shows positive and negative amps for easy diagnosis of current leakage problems• 0-500 Amp variable carbon pile load tester• Unique curved carbon discs ensure maximum contact, fewer hot spots, smoother operation and longer life• Heavy-duty single extruded leads for testing up to 15 feet apart• Test electrical systems on 12/24 Volt systems• Test all battery types• Ideal for testing remotely mounted batteries accurately• INCLUDES: Model 6043 1000 Amp AC/DC Inductive Amp Clamp for checking starter draw or parasitic drain test, also can be used with conventional multi-meters; heavy duty, two wheel tilt-back cart with 8” wheels and 2 trays.• Made in USA of US and Global Components
-
Product
RF Components
-
Our Components product line consists of standard RF components and unique designs for custom microwave applications. We provide rugged, reliable and quality solutions for low and high power attenuation, termination, coupler, and power-divider applications. In addition to our extensive line of standard products, Bird has a reputation for designing custom solutions for custom applications. Bird has done hundreds of special versions of RF components to meet the unique needs of our customers. Common requests for customization include: Special Connectors, Non-Standard Attenuation Values, Mismatch Loads, Exceptional Peak or Average Power Handling Capability, Extremely Low VSWR Requirements, Custom Test Requirements and many others!
-
Product
PXI/PXIe RF Matrix, 16x4, 100 MHz, 75 Ω SMB With Loop-thru
42-727A-101-L
Matrix Switch Module
The 40-727A-101-L (PXI) and 42-727A-101-L (PXIe) are 16x4 75 Ω RF matrices with SMB connectors and Y-axis loop-thru. The 4x-727A/728A/729A range are high density RF matrix modules suitable for switching up to 300 MHz in 50 Ω or 100 MHz in 75 Ω. They are available in 50 Ω or 75 Ω versions with SMB connectors or in 50 Ω versions with a multiway connector.
-
Product
External Load Expansion Connector Accessory for USBHub3c
-
Used for connecting external electronic loads to the USBHub3c for VBUS load testing. It features separate screw terminals for VBUS passthrough from each USB Type-C port (0 through 5). While this board provides a physical wiring interface to access each VBUS channel, the USBHub3c External Load Feature is required to enable VBUS outputs on the USBHub3c.
-
Product
Type 12R2, 8U, 19" Rackmount, MIL-Rugged, Top Load
12R2-8U-TL
-
The 8U, 12R2 is designed to meet the harsh environment of shipboard, airborne, and ground mobile applications per MIL-STDs. Shock isolated versions are designed to attenuate 25G shock inputs to the chassis to less than 10Gs at the card cage.
-
Product
MS-M Style RF Connector Male Contacts RG178
40-969-501-MC
-
The 40-969-501-MC is a 30 piece kit of RF Connector Male Contacts for MS-M style Connector Housing, suitable for RG178 Co-axial Cable.
-
Product
Static Load Cells (500 N to 600 kN)
2580 Series
-
The Instron 2580 Series static load cells are high-precision force transducers optimized for use with 5900 and 6800 Series universal testing systems, capable of measuring loads across a wide range (up to ±600 kN) with accuracy to 0.5 % of reading and sensitivity down to 1/1000th of full scale. Temperature-compensated and calibrated on equipment traceable to international standards, they have automatic recognition with an electronic serial number and support electronic calibration, while offering overload protection (up to 150 % without damage, 300 % without mechanical failure). The 2580’s design delivers high stiffness and reliable alignment under load—making it a robust choice for tension, compression, cyclic, and reverse stress testing in materials and components.
-
Product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-800B Open loop method
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
Product
SMART III RF Moisture Sensor
-
Results are continuous, instantaneous and non-destructive. Used among diverse applications including gypsum, powdered and granular materials, agriculture and wood products. Monitor required to complete system. (Sold Separately): SMART III RF LED Screen OR Touch Screen
-
Product
Road Load Data / Durability
-
Vehicle Durability Testing and Road Load Data AcquisitionA road load data acquisition system from Dewesoft is a perfect vehicle durability testing solution for real-drive tests or tests on the road simulator test benches. Our advanced DAQ technologies will shorten time to test dramatically and make sure you get the correct measurements right the first time.
