Filter Results By:
Products
Applications
Manufacturers
-
product
Call Generator (Voice / Data)
Qosmotec Software Solutions GmbH
The Mobile Network Tester LTS is an automatic call generator, that establishes voice and data calls to and from actual mobile devices in the test system. Voice calls can be generated via the wireless PLMN network using actual mobile devices, via the PSTN network through analogue or ISDN lines or via Voice over IP. Wireless data sessions can be setup through the 3G or 4G network or over WiFi.
-
product
Line Tester
CAT 1 TEST
Monacor International GmbH & Co. KG
Line tester for continuity testing of Cat 5, Cat 6 and ISDN network cables*Connection test with LED display for 8 individual wires and shielding*Continuity, miswire, open, short, crossover, and ground detection*Connector compatibility with the following modular plugs: RJ45 (8P8C), RJ12 (6P6C), RJ11(6P4C, 6P2C)*Network standards supported: Token Ring, 10Base-T, 10Base-T2, 285A, TIA568A/568B*Separate receiver for particularly long and complex cables*The main unit and separate receiver can be attached to one another using a guide rail on the side*Power supply via 9 V block battery (not included)*Supplied with protective bag
-
product
Telephone Line Tester for ISDN Lines
1EA065
ISDN line checker shows the correctness of your ISDN So bus line connections. Indication of the problem is presented with 4 LED (combination of them shows different states and working conditions of the ISDN So bus). The tester uses Phantom power - no need for additional power supplay.
-
product
Network Test LanCaster Pro ST
The NEW Lancaster Pro-ST is a low-cost wire map tester which tests and certifies structured cabling continuity to a TIA568A/B, USOC and ISDN standards. The new Lancaster Pro-ST displays on screen wiring configurations showing the length of all 4 pairs and length of pair to fault up to 150m (500ft).
-
product
LAN Tester / Wiremap Tester & Cable Fault Locator
RapidTrace 700
Compact, Powerful and Easy to use. This high performance low cost LAN Tester / Wiremap Tester and Cable Fault Locator is the perfect tool to enable you to test and certify structured cabling continuity to TIA568A/B, USOC and ISDN standards.
-
product
ISDN-Testers
Is an ISDN Tester for use in the installation and maintenance of BRI S/T/U and POTS accesses – including BRI S/T NT and monitor modes.
-
product
Bit Error Rate Tester - PXI
BERT 1001/1005 Series
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
product
PAM4 Bit Error Rate Tester.
BERT-1102
The BERT-1102 is a 4 or 8-channel PPG and Error Detector for the design, characterization and manufacturing test of optical transceivers and opto-electrical components with symbol rates up to 29 GBaud/s in both NRZ and PAM4 formats. With scalability and exceptional signal fidelity, it is a cost-effective test solution for up to 400 Gb/s communication eco-systems.
-
product
ABex PXI to Analog Bus Bridge with Digital IOs
ABex AM-300 Controller
The ABex system controller ABex AM-300 is required to control the analog bus of a ABex chassis. It is used as an interconnection bridge between PXI and ABex backplane.In addition it features a whole bunch of additional functionality. Despite the 96 open drain outputs it has galvanically isolated IOs, and communication interfaces.
-
product
Bit Error Rate Tester - MATRIQ
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
product
MTM-Bus Tester
PXIe-1149.5
The Corelis PXIe-1149.5 is a versatile, multi-mode instrument for interfacing with MTM-Bus modules. The PXIe-1149.5 adds MTM-Bus master, slave, and monitoring with full IEEE-1149.5 electrical and protocol compatibility with a standard PXIe interface for convenient integration into any Test Program Set (TPS).
-
product
Automated Coherent Receiver Tester
CoRx Tester.
Quantifi Photonics’ CoRx Tester provides automated measurement of key coherent receiver performance parameters. The CoRx Tester is comprised of a pre-configured PXI chassis, a two-channel tunable laser, a polarization controller, and a two-channel Variable Optical Attenuator (VOA) with built-in power meter. Just connect the two optical outputs to your Integrated Coherent Receiver (ICR), connect your ICR to the oscilloscope and let the CoRx Tester software do all the rest.
-
product
KVS Rugged Igniter Tester With Current Monitor
4314
The Valhalla Scientific Model 4314 KVS Digital Igniter Tester is designed to provide extremely safe and reliable resistance testing of explosive or volatile devices. Proven uses include fuses, squibs, igniters, explosive bolts, automobile airbag initiators and many others.
-
product
2 Port BRI-S/T-U ISDN Simulator
BRI-2UST
The unit has two S/T and two U ports allowing ISDN basic rate terminal equipment to be connected together just as if they were connected through the ISDN network.
-
product
2 Port BRI-S/T ISDN Simulator
BRI-2ST
The most inexpensive ISDN simulator on the market. The unit has two S/T ports allowing ISDN basic rate terminal equipment to be connected together just as if they were connected through the ISDN network.
-
product
2 PRI + 16 BRI-S/T ISDN Simulator
CH-16BRI-ST-MOD-2PRI
This unit has two PRI ports and 16 BRI ports allowing ISDN equipment to be connected together just as if they were connected through the ISDN network
-
product
4 Port BRI-S/T-U ISDN Simulator
BRI-2U2ST
The unit has two S/T and two U ports allowing ISDN basic rate terminal equipment to be connected together just as if they were connected through the ISDN network.
-
product
4 Port T1/E1/PRI ISDN Simulator
SIM-4PRI
The most inexpensive ISDN simulator on the market. This unit has four PRI ports allowing ISDN equipment to be connected together just as if they were connected through the ISDN network.
-
product
2 Port BRI-S/T ISDN Simulator PCI
BRI-2ST-PCI
The most inexpensive ISDN simulator on the market. Designed in standard PCI card form factor it has two S/T ports allowing ISDN basic rate terminal equipment to be connected together just as if they were connected through the ISDN network. Simulator card does not require any OS drivers, completely software independent and it take only power from the host computer.
-
product
Basic Rate and Primary Rate ISDN Network Simulator
Emutel Duo
Emutel Duo is a convenient and flexbile basic rate and primary rate ISDN network simulator. With 3 software selectable S/U interfaces and optional 2 E1/T1 interfaces you can test and develop a full range of ISDN equipment.
-
product
2 Port T1/E1/PRI ISDN Simulator PCI
SIM-2PRI-PCI
The most inexpensive ISDN PRI simulator on the market. Designed in standard PCI card form factor it has two PRI(T1 or E1) ports allowing ISDN PRI equipment to be connected together just as if they were connected through the ISDN network. Simulator card does not require any OS drivers, completely software independent and it take only power from the host computer.
-
product
De-Energized Tester
ALL-TEST PRO 7 PROFESSIONAL
The ALL-TEST PRO 7™ PROFESSIONAL uses our proven, patented technology to look beyond vibration, temperature, and ultrasound test methods – giving you instant answers on your motor’s health. It represents our 7th generation in product innovation that ensures the reliability of motors in the field and helps to maximize the productivity of maintenance teams everywhere.
-
product
De-Energized Tester
MOTOR GENIE
The MOTOR GENIE® can see more than a megohmmeter, resistance tester, or RCL tester, making it the perfect tool for troubleshooting, startup, and quality control of low voltage AC induction motors.
-
product
Insulation Testers
Can be used for quantitative and qualitative analysis of insulation. It also automatically measures voltage, capacitance and residual current.
-
product
Torque Testers
Torque testers are ideal for a variety of applications in light assembly and can be used to test hand tools, power tools and even pulse tools.
-
product
Sensor Tester
*Connection facilities for DC 2-wire and 3-wire sensors, *Change in switching status signalled visually and acoustically, * 15 V operating voltage for sensors when using a 9 V block battery, * Switches off automatically when not in use, * Visual indicator for operating voltage, switching status and low battery
-
product
Cable Testers
Passage test:Detects open wires, short circuits and faulty wiring. Pass / fail test using a given pattern cable. Finding intermittent connections.Save cable data for documentation purposes. Print wiring diagrams. Printing labels. Log and print error logs.Graphical representation of the wiring of cables, graphical comparison of two cables. Easy, intuitive, graphical tracking of individual wires of a cable.Quickly install quick-mount boards for a variety of connector types such as BNC, RJ45, Sub-D, flat-ribbon connectors, and many more.Easy connection to the PC via USB .Light Director System:LED-led assembly of connectors. Optional also with voice output. High degree of safety due to fault checking during assembly.
-
product
Multifunctional testers
MI 3152H EurotestXC 2,5 kV
MI 3152H EurotestXC 2,5 kV is an instrument from the new generation of Metrel’s multifunctional measuring instruments. The already well known functions like complete installation safety testing according to IEC/EN 61557 and AUTO SEQUENCE testing of TN and TT earthing systems expanded with insulation resistance measurement with the test voltage up to 2,5 kV are managed by a completely new user interface based on large colour touch screen display.
-
product
Battery Testers
Wireless battery and electrical system analysis tablet using Adaptive Conductance, an advanced battery analysis method that produces a more accurate examination of the battery’s cold cranking ability and reserve capacity, vital to determining a battery’s true health. The 7-inch Android touchscreen tablet can display a quick health status of the existing battery, register a new battery and perform advanced battery and electrical system diagnostics.
-
