Filter Results By:
Products
Applications
Manufacturers
Absorbing Clamps
measure radiated emissions. AKA: Ferrite Clamps
-
product
RFI Power Emission
AFJ receivers and accessories for the disturbance power using the absorbing clamp measurement, are conforming to CISPR 16-1-1 and CISPR 14-1.
-
product
Absorbing Clamp
AB-CLP
• EMI Receiver equipped with absorbing clamp can indirectly test radiated interference power of household electrical appliance, power tool and similar electrical appliance with frequency from 30~300MHz.
-
product
Absorbing Clamps
The absorbing clamps also known as ferrite clamps are used for measuring disturbance power on power input lines as well as other auxiliary I/O lines.
-
product
Absorbing Clamps
The Absorbing Clamp was designed to measure the disturbance power according to CISPR 16-2-2 in the frequency range 30-1000 MHz, it complies to the technical requirements of CISPR 16-1-3.
-
product
Clamp Multimeters
Clamp meters test AC/DC voltage, DC voltage, resistance and continuity. Measure conductors at any point in the wire or cable.
-
product
Clamp Meters
Our clamp meters measure both high and low AC and DC currents as well as earth leakage and earth resistance. With variable jaw sizes, max current readings up to 2000A AC/DC and features including TRMS, data logging and temperature readings we have clamps suitable for a wide range of electrical applications.
-
product
Clamp Meter
KT-266F
3 1/2 digits LCD with max. reading of 1999AC/DC voltage and Resistance measurementFrequency test50 mm Large jaw DiameterPlug - insulation tester adapter 500 VDC (optional)Audible continuity, Data hold ,Diode testLow power indication
-
product
Leakage Clamp Meters
3920 CL
Standard Electric Works Co., Ltd
● Designed for testing AC current and AC voltage. ● 5 ranges for AC current testing.● The best resolution of leakage current measurement is 0.1mA.● Frequency selection : 50/60 Hz and Wide.● Data hold function.● Low battery indication.
-
product
Earth Ground Clamp
1630-2
The 1630-2 FC clamp measures earth ground loop resistances for multi-grounded systems using the dual-clamp jaw. This test technique eliminates the dangerous and time-consuming activity of disconnecting parallel grounds, as well as the process of finding suitable locations for auxiliary test stakes.
-
product
Clamp Meters
Kyoritsu Electrical Instruments Works, Ltd.
The clamp on the device is simply placed around a live wire. This allows one to measure the current on a wire without interrupting the operation of the electrical appliance. A clamp meter uses digital technology to bring instantaneous readings.
-
product
Clamp Meters
Amprobe invented the first clamp meter in 1948 and has continued to innovate and evolve. Today Amprobe offers several categories of clamp meters – from the rugged CAT IV rated Navigator Series, to the versatile Swivel clamp meters, to the compact mini-clamps. Whether you work on residential, commercial, or industrial applications you’ll find an Amprobe tool that fits your needs.
-
product
AC/DC Clamp Meter
2660 CL
Standard Electric Works Co., Ltd
● 4000 counts.● Voltage measurement, current measurement, resistor measurement, frequency counter, capacitor measurement.● Bargraph indication.● Range change function.● Data hold function freezes the reading.● REL function.● Peak function.● Diode measurement.● Max / Min function.● Continuity check.● Low battery indication.● Auto Power Off (APO) function.● Safety design throughout with no exposed metal parts, shielded banana plugs and recessed input terminals.
-
product
Digital Clamp Meter
Check out our VIDEO on the left side and take a quick tour of AstroAI Multimeter! TEST A WIDE RANGE of measurements including Voltage, AC Current, Resistance, Continuity, Capacitance, Frequency, and Temperature, Tests DiodesPROFESSIONAL LEVEL features includes True RMS for accurate AC Current and Voltage readings. Also includes Auto-Ranging for faster and more accurate results
-
product
C/I Clamp Meters
CLAMPMETER,400A AC (CM-330)
*AC current measuring capability up to 400 amps*Compact size, fits easily into tool pouch*Data hold and Max hold to capture important readings*2000-Count LCD*Lifetime Limited Warranty*Accessories included: (1) 9V battery, carrying case*Lifetime Limited Warranty
-
product
DC Clamp Meter
Shenzhen UYIGAO Electronic Technology Co., Ltd
Is used to measure the DC currents.
-
product
Clamp Meters
Rishabh Instruments Pvt. Ltd.,
Measures, calculates and displays power parameters of single phase or three phase systems. It features bluetooth communication with Android Mobile App. and software for PC for Data Logging, report Generation & Analysis
-
product
Clamp Meter
KT-3500
• Non - intrusive AC and DC current measurement• 10mA resolution• Average responding, RMS calibrated• Auto ranging /Auto zeroing• Data Hold • Low battery indicator• Auto Power OffMeasuring Range: 0 - 500A DC or ACAuto ranging : 50A/500AResolution: 10mA in 50A range, 100 mA in 500A rangeBasic Accuracy: ±1.3% rdg ±5 digitsTemperature coefficient: ±0.05% of rdg /°CFrequency range: DC in DC: 40 HZ to 400 HZ in ACOverload capacity: 500 ADielectric strength: 3.7 KV RMS.50 Hz 60s(EN61010-2-032 Cat III, 300V Pollution Degree 2)Operating Temperature: 0°C to +50°CBattery removed: -20°C to +60°COperating Humidity : <80%RHPower supply: 9V alkaline batteryBattery life: 20 hours dependent duty cycle Display.: 5000 countDimensions: 184×71×31mmMax jaw capacity: 21mm ø CableMax jaw opening: 25mm
-
product
Flex Clamp Meters
*Flex Clamp Current Probes expand existing meters *Compatible with most meters using universal banana leads*Flexible Coil adds accessibility - easily maneuvering around cables that are in hard to reach areas and large enough to thread around larger conductors
-
product
DC/AC Clamp Meter
SE-01
High Resolution DC/AC 10mA. 23mm Large jaw Diameter. One Touch Zero for DCA adjustment. Large 3 1/2 Digits LCD (1999counts). Auto power off,Data hold. Diode & Continuty Test. Capacitance Test
-
product
Amp Clamp
PPDCM80
The Power Probe Digital Clamp Meter is an 80amp, auto-ranging clamp meter designed specifically for the automotive technician. This meter is rated CAT III 600V and can measure Volts, Amps, Ohms, Frequency and Temperature, necessary for automotive electrical testing. This meter’s diagnostic applications include (but are not limited to) Parasitic Draw, Crank Current testing and HVAC Temperature testing.
-
product
AC/DC Clamp Meter
3904 CL
Standard Electric Works Co., Ltd
● 4000 - count LCD.● Full automatic measurement. ◎ Voltage measurement. ◎ Current measurement. ◎ Resistor measurement. ◎ Capacitor measurement ◎ Frequency counter.● Range change function.● Data Hold function freezes the reading.● Continuity check.● Diode measurement.● Low battery indication.● Auto Power Off (APO) function.● Safety design throughout with no exposed metal parts, shielded banana plugs and recessed input terminals.
-
product
AC Clamp Meter
CM3289
Use in even more applications with an optional flexible sensor. Measure both wires in confined spaces and thick wires with a single instrument.
-
product
Metra Power Clamp
1000A
Metra Power Clamp 1000A/400A measures, calculate and displays important electrical pa-rameters of single phase or three phase power system. It also features Resistance, continuity, diode and non contact voltage detection.
-
product
AC/DC Clamp Meter
3810 CL
Standard Electric Works Co., Ltd
● Full auto range for V.A and Ω functions.● Data hold function freezes the reading in dimly lit or hard to reach places.● Low battery indication.● Built-in buzzer for continuity test.● Safety design throughout with no exposed metal parts. Shielded banana plugs and recessed input terminals.● Ohm function ideal for checking continuity of relays transformers and motor coils.
-
product
Clamp Meter
KT-266C
3 1/2 digits LCD with max. reading of 1999AC/DC voltage and resistance measurementTemperature test50 mm Large jaw DiameterPlug - insulation tester adapter 500 VDC (optional)Audible continuity test, Data holdLow power indicationSpecificationSpecificationsRangeAccuracy±(%rdg + digits)AC Voltage 200/750V 1.2%rdg+10dAC Current 20/200/1000A 2.0%rdg+5dDC Voltage 200mV 0.5%rdg+1d2/20/200V 0.8%rdg+1d1000V 1.0%rdg+2dResistance 200/20K/2M Ω 1.0%rdg+2dTemperature 0 - 400°C 1.0%rdg+3d400 - 750°C 2.0%rdg+1dDimensions 230mm(L) x 70mm(W) x 37mm(H)Unit Price (USD) 4.0Min.Quantity (pcs) 1000Weight(g) 310pcs/carton 34N.W. 10.6G.W. 11.5Packing carton size 52 x 36 x 40 cm
-
product
H/L Voltage Clamp Meters
High Voltage Current Transformation Ratio Tester breaks traditional structure, specially designed for high and low voltage first and secondary loop current, variable ratio, and current leakage test; apply the latest CT technology and mask digital integration technology, composed of special high-voltage clamp, low voltage clamp, host, high voltage insulation rod and monitoring software, etc; its wireless transmission test data can penetrate multiple building obstacles with a straight-line distance of 30 meters.
-
product
Current Clamps and Transducers
High-accuracy Current Sensors and TransducersHigh-accuracy sensors for AC/DC current measurement and power analysis. From current clamps to high-precision zero flux current transducers and Rogowsky coils.
-
product
AC/DC Clamp Meter
3800 CL
Standard Electric Works Co., Ltd
● Full auto range for V.A and Ω functions.● Data hold function freezes the reading in dimly lit or hard to reach places.● Low battery indication.● Built-in buzzer for continuity test.● Safety design throughout with no exposed metal parts. Shielded banana plugs and recessed input terminals.● Ohm function ideal for checking continuity of relays transformers and motor coils.
-
product
High Altitude Wiring Clamp
Weshine Electric Manufacturing Co., Ltd
1. The operation is simple, through pushing and pulling the special operation lever can realize the clamp mouth free opening and closing, complete the wiring work.2. Connection clamp between the upper and lower jaws of the use of the principle of moving pulley to save the effort, the use of smaller tension can be obtained larger clamping force.3. There is a steel needle inside the clamp mouth to ensure good contact between the clamp mouth and wiring position
-
product
Self-testing Static Grounding Clamp
Bond-Rite CLAMP
In many branches of the process industries, fires and explosions can result from electrostatic discharge in hazardous areas. Even relatively small sparks have sufficient energy to ignite many flammable vapours, gases and even airborne dusts. In situations, where this risk exists, static grounding (earthing) and bonding clamps are required wherever mobile or portable conductive plant items (such as drums and vessels etc) are used.
