RTD Simulators
calibrate resistance temperature detection systems.
-
Product
Distributed Simulation & Test Environment
-
Modular hardware and software architecture with multipurpose modules and components in a common and reconfigurable simulation and test environment easily adaptable to meet project‐ and customer‐specific requirements.
-
Product
NI-9217, 4-Channel, 400 S/s Aggregate, 0 Ω to 400 Ω, PT100 RTD C Series Temperature Input Module
779592-01
-
4-Channel, 400 S/s Aggregate, 0 Ω to 400 Ω, PT100 RTD C Series Temperature Input Module - The NI‑9217 is a resistance temperature detector (RTD) input module. You can configure the NI‑9217 for two sample rate modes: high sample rate or high resolution. The NI‑9217 is compatible with 3‑ and 4‑wire RTD measurements, and it automatically detects the type of RTD (3‑ or 4‑wire) connected to the channel and configures each channel for the appropriate mode. The module provides per channel current excitation. The NI‑9217 features calibration and includes a channel‑to‑earth ground double isolation barrier for safety, noise immunity, and a high common-mode voltage range.
-
Product
Tailor-Made to Simulate Low-Temperature Plasma Sources and Systems
Plasma Module
-
The Plasma Module is tailor-made to model and simulate low-temperature plasma sources and systems. Engineers and scientists use it to gain insight into the physics of discharges and gauge the performance of existing or potential designs. The module can perform analysis in all space dimensions 1D, 2D, and 3D. Plasma systems are, by their very nature, complicated systems with a high degree of nonlinearity. Small changes to the electrical input or plasma chemistry can result in significant changes in the discharge characteristics.
-
Product
Power Amplifer AURORA Digital Interface For Simulator Application
PAV DIA01
-
PAV DIA01 is the optional accessory unit and Aurora digital interface for PONOVO’s power amplifiers which could convert the analog input signal into digital signal, supporting communication between power amplifier and simulators via AURORA protocol.
-
Product
8-Channel VME Isolated Resistance Simulator
V420
-
The V420 is an 8-channel, isolated, programmable resistance simulator. It uses entirely solid-state simulation to eliminate transient errors associated with relay switching, and provide for monotonic resistance changes. Channels are individually programmable in four resistance ranges, from 5 ohms to 65.5K. Channels can operate from microvolts up to 35V / 50mA. Overload protection and channel error detection are included.
-
Product
Graphical Debugging for Verilog, VHDL, and C++ Simulators
BugHunter Pro
-
BugHunter uses the SynaptiCAD graphical environment and supports all major HDL simulators. It has the ability to launch the simulator, provide single step debugging, unit-level test bench generation, streaming of waveform data, project management, and a hierarchy tree. The unit-level test bench generation is unique in that it lets the user draw stimulus waveforms and then generates the stimulus model and wrapper code and launches the code. It is one of the fastest ways to test a model and make sure that everything is working correctly. The debugger also has exceptional support for VCD waveform files.
-
Product
Battery Cell Simulation / Emulation
BMS
-
Efficiency, reliability and safety of modern lithium ion batteries for electric vehicle drives strongly depend on the battery management system (BMS) as their electronic control unit.
-
Product
Bipolar DC Power Supply / Battery Simulator
IT6400 Series
-
The unique bipolar voltage/current output makes IT6400 series can be used as a bipolar power source or a bipolar electronic load. The battery simulating function is especially applicable for development and high speed production testing of portable, battery-operated products.
-
Product
Thermometer / Cardiac / Invasiv, non Invasiv Blood Pressure Simulator
TBH-400
-
Test device for functional testing of medical thermometers (DIN EN ISO 80601-2-56), cardiac output, invasive (IEC 60601-2-34) and non-invasive blood pressure devices (IEC 60601-2-30).
-
Product
CAN & LIN bus Custom Test & Simulation Software
CanX
-
Schleissheimer Soft- und Hardwareentwicklung GmbH
CanX is the custom testing and simulation software for CAN and LIN bus for specific user groups. The run-time software is designed to execute predefined or automated tasks in testing, work preparation, production, repair or project management.
-
Product
Solar Simulator
-
It is an LED light source for evaluating the performance of organic solar cells in indoor light applications.A neutral white LED light source equivalent to a color temperature of 5000 K, achieving an effective irradiation area of 50 × 50 mm.The illuminance can be changed without changing the height of the light emitting surface with low illuminance (200 lx) and high illuminance (1000 lx).
-
Product
Panel-mounted Power Amplifier(Hardware In The Loop Simulation)
PA30Bi
-
PA30Bi is the panel-mounted type real time simulation amplifier with three-phase current and four-phase voltage.
-
Product
PXI/PXIe Analog Output/Current Loop Simulator Module - 16 Channel
43-765-001
-
The 41/43-765-001 is a PXI/PXIe 16-channel Analog Output Module designed to meet the requirements of industrial control applications utilising current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signalling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
Product
Environmental Simulation Chambers
-
GTEMCELL , currently provide environmental test chambers made by LIB.Our standard range of test chambers includes bench top and floor standing models, across temperatures ranging between -65℃ and +150℃ (from -80℃ to +200℃ for specific applications), and humidities between 10% and 98% RH.
-
Product
Voltage Dip & Swell Simulators
VDS Series
-
A simulator to reproduce voltage variation phenomena in commercial power supplies (AC100V/200V).This type of immunity test against voltage variation phenomena is defined in IEC 61000-4-11 and is widely used in many industries.
-
Product
Simulation Environments Software
Modelica
-
Modelica Libraries with a large set of models are available (overview, details and download). Especially, the open source Modelica Standard Library contains about 1280 model components and 910 functions from many domains.
-
Product
PXI Analog Output/Current Loop Simulator Module - 4 Channel
41-765-004
-
The 41/43-765-004 is an 4-channel Analog Output Module designed to meet the requirements of industrial control applications utilizing current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signaling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
Product
Basic Rate and Primary Rate Simulator
emutel Pro
-
Emutel Pro has the same features as the Emutel but has 2 BRI and 2 PRI which will allow you to test both basic rate or primary rate equipment or basic to primary links to be set up. Emutel Pro has optional network support and protocol analysis.
-
Product
Steady-state Solar Simulator For PV Modules
SORAS LS
-
In certification laboratories for photovoltaic modules, steady-state solar simulators are mostly used for stabilization / light soaking tests (MQT 19) and hot-spot endurance tests (MQT 09) according to IEC 61215 and IEC 61730. An initial stabilization is required for all PV modules that undergo a standard test procedure. For the hot-spot endurance test (MQT 09), it is important that the operator has easy access to the front and back site of the module. During the test, it is necessary to shade one cell after each other to take infrared pictures, which requires good visibility of the entire back side. Our swiveling module holding system enables easy access to the front and back side of the module.
-
Product
Network Emulation, Delay Simulation, Bandwidth Emulator & WAN Simulation
-
GigaNet System’s network emulation appliances provide precision, performance and predictability in your test infrastructure resulting in optimized system performance and robust system behavior under real world network conditions.
-
Product
MIL-STD-1553 A / B Test And Simulation 3U PXI Module
PXI-C1553
-
*Dual redundant*1, 2 or 4 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*PXI trigger on 1553 bus events*10 programmable, discrete I / O (up to 30V)*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, LabView Real-Time and other systems
-
Product
Single Or Dual Stream MIL-STD-1553A/BTest And Simulation Module For Standard Ethernet
ANET1553-x
-
The ANET1553-x is a member of AIM’s new line of Ethernet based modules for analysing, simulating, monitoring and testing MIL-STD-1553A/B databuses. For wireless applications, an ANET compatible USB Wifi dongle is optionally available. The capability to execute Python scripts in the ANET is a standard feature. For applications with multiple ANET devices AIM offers the ADock ANET Docking Station to host up to 4 ANET modules.
-
Product
Automotive Transient Surge Simulators
ISS/JSS Series
-
Simulator to reproduce various transient surge phenomena which are generated in vehicles and defined in the international standard ISO-7637-2 Standard for evaluating automotive electronics immunity. Please contact us for transient testers to perform testing to manufacturers' private standards.
-
Product
Gyro Simulator for Aircraft or Bench Use
TA-256A
-
This is a transformer isolated gyro simulator that can substitute for the KI256 attitude indicator and thus eliminate the requirement to remove that gyro to a remote stand and route a vacuum or pressure source out to the aircraft.
-
Product
ARINC 429 Test & Simulation Interface for PCI Express
PCIe-C429X
-
Avionics Interface Technologies
16, 32, or 64 ARINC 429 Channels (up to 32 Tx & 32 Rx) - Programmable Tx channel output amplitude - Programmable High/Low Speed Operation - Eight (8) Discrete I/O (Four (4) inputs, and four (4) outputs) - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection - Data capture filtering, 100% bus recording, and physical bus replay - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B time code encoder/decoder with free-wheeling mode - Application Interface supporting C/C++, C# and VB.NET Development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
Electronic Warfare MMI and HMI Simulators
MS 1600
-
The EW IFU (Electronic Warfare Interface Unit) interfaces between Cockpit electronics viz., RWR Display Unit (DU), New control Box (NCB), CMDS Control/Display units and Simulator Host Computer (HOST). The EW IFU transmits the status of the cockpit control units to the host, receives display data from the host and transfers the same to RWR DU, NCB and CMDS CCU/CDU. The display data for the RWR DU received from the host would comprise of the complete symbol data in respect of emitters that are to be displayed based on the data from the Instructor Station (IS) and control input from the cockpit. The display unit receives and presents the data as symbology on the display screen. The EW IFU based on the PC–AT.
-
Product
Simulation and Model-Based Design
Simulink
-
Simulink is a block diagram environment for multidomain simulation and Model-Based Design. It supports system-level design, simulation, automatic code generation, and continuous test and verification of embedded systems. Simulink provides a graphical editor, customizable block libraries, and solvers for modeling and simulating dynamic systems. It is integrated with MATLAB, enabling you to incorporate MATLAB algorithms into models and export simulation results to MATLAB for further analysis.
-
Product
NI-9226, 8-Channel, 400 S/s Aggregate, 0 Ω to 4000 Ω, PT1000 RTD C Series Temperature Input Module
785189-01
-
8-Channel, 400 S/s Aggregate, 0 Ω to 4000 Ω, PT1000 RTD C Series Temperature Input Module - The NI‑9226 is a resistance temperature detector (RTD) input module. You can configure the NI‑9226 for two sample rate modes: high sample rate or high resolution. The NI‑9226 is compatible with 3‑ and 4‑wire RTD measurements, and it automatically detects the type of RTD (3‑ or 4‑wire) connected to the channel and configures each channel for the appropriate mode. The module provides per-channel current excitation. The NI‑9226 features calibration and includes a channel‑to‑earth ground double isolation barrier for safety, noise immunity, and a high common-mode voltage range.
-
Product
Infrared Simulation Services
-
INO offers a simulation service to assist with the hardware and software design of infrared and electro-optical devices. Precise performance predictions help integrators understand application requirements and bring application performance in line with client specificationsbefore the advance design and fabrication phases. For a minimal investment, infrared simulations help minimize risk in the early stages of development.
-
Product
2 PRI + 32 BRI-S/T ISDN Simulator
CH-32BRI-ST-MOD-2PRI
-
This unit has two PRI ports and 32 BRI ports allowing ISDN equipment to be connected together just as if they were connected through the ISDN network
