Current Transducers
-
Product
Series Precision Multi-Ratio Current Transformers
PMT25090
-
Power Measurement Technologies Inc.
Precision two-stage toroidal current transformers find application as the reference in determining the accuracy of instrumentation current transformers.
-
Product
Current Probe Calibrator
KSZ
-
PMK Mess- und Kommunikationstechnik GmbH
Since Current Probes are often exposed to hard working conditions, a performance check is recommendedbefore every use. These Current Probe Calibrators generate square wave pulses from 0.05 A to 1000 A with an accuracy better 1%. They qualify for calibration and adjustment of Current Probes.
-
Product
1-3 Piezo-composite Transducers
-
Custom-designed transducers using 1-3 piezo-composite materials for a wide range of lower frequency applications.
-
Product
AC/DC Current Clamp Meter
CM600
-
Clamp opens up to 1 inch (25.4 mm). One rotary switch operation. Large 4 digit LCD display. AC/DC Voltage measurement up to 600 Volt. AC/DC current measurement up to 600 A.Relative measurement. One touch auto zero.
-
Product
30 A Current Shunt
34330A
-
Measure current safely with this precision 0.001 ohm resistor housed in a plastic case surrounded by epoxy.
-
Product
Current sensors
-
Assistance systems support the driver and assure safety in the latest generation of automobiles. Infotainment systems entertain passengers during car journeys and provide navigation. Seats are no longer adjusted manually, and doors are opened and closed with electric motors. The ever increasing electrification is driven by many other factors besides convenience and safety though.
-
-
Product
Split-Core Current Transformers
CTS Series
-
Continental Control Systems LLC
The CTS series CTs are available with windows from 0.75 inch up to 2.0 inch. They have a removable section, so that they can be installed without interrupting the circuit. 0.333 Vac output at rated current Accuracy ±1% from 10% to 100% of rated current Phase angle <2° degrees at 50% of rated current (valid for 70 A or higher) 8 ft. twisted-pair wire, 600 Vac rated UL recognized for voltages up to 600 Vac, CE mark, RoHS
-
Product
Transducer Calibration
m+p SensCal
-
Regular transducer calibration is an essential requirement for maintaining the accuracy, reliability and repeatability of the results obtained from a measurement system. m+p international’s m+p SensCal program provides a quick and simple process for calibrating accelerometers (piezo-electric with charge output or IEPE, piezo-resistive, capacitive) in your laboratory, as well as velocity or displacement transducers.
-
Product
Clamp type AC Current Sensor／for Low Leakage Current Measurements(ZCT Series)
ZCT-18S
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Best sensor for low leakage current measurements of less than 1mA.*Ultra compact size with 18mmφ jaw opening capability.*High sensitivity and least affection from external magnetic field.
-
Product
AC Current Digital Clamp Meters
-
Precision Mastech Enterprises Co.
Handheld, safe, and non-contact electrical tools designed to measure alternating current (AC) without disrupting the circuit
-
Product
Impulse Current Generator
-
Weshine Electric Manufacturing Co., Ltd
Impulse current generator is mainly used to test the ability of electrical equipment to withstand strong impulse current, widely used in lightning arresters and electrical and electronic equipment in operation conditions of oscillation wave immunity test, can also be used for other research tests.
-
Product
Wireless Primary Current Recorder Meter
GF2015
-
Beijing GFUVE Electronics Co.,Ltd.
GF2015 is a wireless primary current recorder equipped with a 433M for transmit the recorded data into the user''s PC by our PC-Link Software. It is a good assistant of power monitor system. The recording interval can be set from 1- 60 min. The PC-Link Software can generate reports and create graphs for profile analysis.
-
Product
Power Cell Power Transducers for Wide Ranging AC/DC Loads
PH-3A and PH-1000
-
You can know the load on an electric motor by measuring the electric current going to the motor (Amps). But, this is not the best way to do it since a lightly-loaded motor doesn't use the electricity very efficiently. (In technical terms, the power factor is low.)A better way to know the load is to measure the motor power. (Power is measured in Horsepower or Watts.) Motor power gives you a straight line so it works well even when the motor is lightly loaded.The Power Sensors that we make measure the motor load (Horsepower or Watts) and send a signal to meters or computers. The operator can see what the status is on the meter or, the computer can make decisions.
-
Product
Stand-Alone Current Sensors
-
The Aanderaa Current Sensors are based on the backscatter acoustic Doppler principle.
-
Product
Flexible Leakage/Line Current Tester
RLM-10+
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
●Low-pass filter equipped, it can be cut the noise which is over 150Hz frequency.●Even Coreless Coil but Least Influence from External Magnetic Field and Residual Current●Superior Flexible CT enables Leakage Current Measurement●Backlight Function useful for measurement in the dark place
-
Product
Dual Voltage Buffer with Current Drive
BUF-01
-
The BUF-01 Voltage Buffer is a dual channel buffer capable of driving up to 50 mA of current on each channel at up to ±10 V output. The buffer has a 2nd order low pass filter with 3 dB point of 119 kHz to remove high frequency noise. The unit’s differential inputs are built to withstand high DC over-voltages up to ±50 VDC and greater than ±100 V transients. Gain of the unit is 1 allowing for minimal insertion issues.
-
Product
Through Hole type DC Current Sensor／for DC Leakage Current Measurements
DCZCT-20MH
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*DC earth fault measurement for solar power system*Least affection from the magnetization of core and temperature fluctuation*DC leakage current measurements*Convenient ＋5V single polarity power supply
-
Product
General Performance Differential Pressure Transducers
-
These general performance Baratron® differential capacitance manometers measure the difference in pressure between the inlet tube and the reference cavity. The reference cavity can be connected to any pressure or vacuum source, or be open to local atmosphere.
-
Product
Current Digital Set Point Relay
-
These Digital set point relay for current (type mrd2011-a) are field proven with excellent sensitivity and are with two independent outputs and are used as under current and over current controlling operations. The two independent outputs are programmable in a specific range i. E. The range if it is 25a the settings can be made within the range of 250 a. This facility of having the liberty to set the required current is added advantage in the digital meters of these models available in the market. The set points are field settable within the range mentioned in the model. these relays have inbuilt timers and this facility enables the user to avoid external timers and external wiring. The timers are programmable from 0 second to 20 seconds. The ranges available are up to 2500 a. The dimensions are compact and are of 96 mm x 96 mm x 65 mm only. The auxiliary supply for the relay is 110v ac or 230v ac.
-
Product
Through Hole type AC Current Sensor
CT-30AR
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
For measuring electric power (through hole type)
-
Product
30A, 100MHz High Sensitivity Current Probe
CP031A
-
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
Product
Generator Of Direct Current And Voltage
GPTN
-
The module is intended for use as part of information measuring systems based on the VXI-bus trunk. The module is designed to generate constant current or constant voltage.
-
Product
Primary Current Injection Testing
KAM
-
This substation testing device is designed to grant high current output when needed in substation commissioning activities.
-
Product
Torque Cell Transducer
-
Unitech Scales And Measurements Pvt. Ltd
*UNITECH’S manufacturers two type of Torque transducers 1. In-Line Rotating Torque Transducers with / without speed sensors 2. Reaction Type Torque Transducers.*Transducer ranges from 1 Kg-m to 600 Kg-m with various types like Flange mount, Hallow type, Shaft mount, etc.
-
Product
Test and Measurement Grade Pressure Transducer for CAN Bus
P896
-
The P896 is a test and measurement grade pressure transducer for applications requiring high accuracy and outstanding performance through ambient temperature changes. The P896 is digitally compensated and corrected to provide high accuracy pressure measurement in a robust cylindrical form factor.
-
Product
SparkFun Current Sensor Breakout
ACS723 (Low Current)
-
The low current version of the SparkFun Current Sensor Breakout is a high accuracy board that utilizes the ACS723 for low to moderate AC and DC current sensing applications. The ACS723 sensor uses a Hall effect sensor to output a voltage relative to the current flowing through the IP+ and IP- pins on the board. The advantage of using a Hall effect sensor, specifically, is that the circuit being sensed and the circuit reading the sensor are electrically isolated meaning that, although your Arduino is running on 5V, the sensed circuit can be operating at higher DC or AC voltages!
-
Product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-600B Open loop method
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
Product
100-Amp Current Calibrator And AC/DC Transconductance Amplifier
2555A
-
World’s Leading Precision 100-Amp AC/DC Current Standard - For 30 years Valhalla Scientific’s design has proven rock-solid reliability in metrology labs worldwide. The 2555A is a calibration powerhouse with wide-ranging applications and unsurpassed quality.
-
Product
Mini AC Leakage Current Clamp Indicator
MLD-18
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
・The LED will blink when detection leakage current exceeds AC 15mA.・Supports ELB with high-speed detection of 20ms.・The operating period is about one month, which is suitable for detecting intermittent leakage current.
