Leakage Current Clamps
Measure low current emf surrounding a conductor.
-
Product
Metra Power Clamp
400A
-
Metra Power Clamp 1000A/400A measures, calculate and displays important electrical pa-rameters of single phase or three phase power system. It also features Resistance, continuity, diode and non contact voltage detection.
-
Product
DMX current dimmer
LDC-41
-
4 channel DMX driver/dimmer for 350-1000mA constant current LED products. Drives RGB, RGBW, RGBA or 4 channels of single colour products. 2-12 LEDs per channel, depending on your choice of external power supply.
-
Product
Eddy Current Chassis Dynamometers
-
Cradle- or single-roll (top-mount) dynamometers accommodating single- or tandem-axle vehicles, with continuous vehicle power ranges from 50 hp to 622 hp (37 kW to 464 kW), Taylor’s chassis dynamometers allow a top recommended speed of 90 mph (145 kph) at full load. Look to our experts to not only help you select your optimal system, but also to provide design, configuration, installation and training for a total solution that integrates seamlessly with your operation.
-
Product
Automotive Fuse Current Probe
FUSE PEEKER
-
Automotive Diagnostics and Publishing
Automotive Fuse Peeker Current Probe for Testing Injectors, Coils, Solenoids and most components. The FUSE PEEKER Automotive Fuse Current Probe works with your own scope, the Auto Scope 1 or any other type of oscilloscope. It uses magnetic sensor technology, which is accurate and safe for your tool. It can detect small amounts of current as small as 5 milli-amps.
-
Product
AC Clamp Power Meter
CM3286 Series
-
Measure power ranging from 5 W at a low current of 60 mA to 360 kW. In addition to current, voltage, and power, measure simple integral power consumption and phase sequence. Discover manipulation of electric meters by comparing meter and integral power consumption measurements. Discover theft by measuring leakage current.
-
Product
Device Current Waveform Analyzers
-
The dedicated Current Sensors measure from 100 pA level dynamic current up to 10 A with a maximum of 200 MHz bandwidth. The mainframe acquires the signal from the sensors by a maximum of 1 GSa/s sampling speed and 14-bit and 16-bit wide dynamic range. This combination allows you to measure quite wide range of dynamic current, for example, from standby/sleep state to active state, at a single measurement. In addition, the wide bandwidth and the high speed acquisition enable you to measure high speed pulse response even less than 100 ns previously very difficult with existing instruments.
-
Product
Rugged Igniter Tester With Current Monitor And Single Connection For Measurement And Charging
4314 KVM
-
The Valhalla Scientific Model 4314 KVM Digital Igniter Tester is designed to provide extremely safe and reliable resistance testing of explosive or volatile devices. Proven uses include fuses, squibs, igniters, explosive bolts, automobile airbag initiators and many others.
-
Product
HPC High Current Probes, 100 – 187 mil (2.54 – 4.75 mm)
HPC
High Current Probe
100 – 187 mil (2.54 – 4.75 mm)
-
Product
Digital Volt Or Current Meter
CS1/CS2-VA
-
Measuring Voltage or Current for DC / AC / TRMS Accuracy: DC: +/-0.04% or AC: +/-0.1%; Display range: -19999~29999 User function, Easily programmable via the front panel. 1 relay, 1 Analogue output or RS 485 communication port in option with flexible functions. CE approved
-
Product
Standard - 1.44 (41.00) - 4.50 (128.00) High Current Probe
HCP-13A
High Current Probe
Current Rating (Amps): 15Average Probe Resistance (mOhm): 25Test Center (mil): 125Test Center (mm): 3.18Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cyles): 250,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
3 Phase Flexible AC Current Probe
DRP 503/18
-
The new DRP 503/18 is a 3 Phase Flexible AC current Probe utilising the Rogowski principle, with 3 channel integrator housed in DIN Rail Mounted Enclosure. The flexible and lightweight measuring head allows quick and easy installation in hard to reach areas and with large conductors.
-
Product
AC/DC Flexible Leakage/Line Current Probe
FAD-100
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Long Time Record of Measurement by Input Power Supply・Detection of Both AC Current and DC Current At Once・Detection of Small DC current Inside Large AC Current・Freely Bending with Flexible Clamp Sensor of Inside Diameter 200mm・Useful for difficult Access Locations with Wide Ranges up to AC/DC 1000A
-
Product
AC/DC Digital Clamp Tester
TCM-45E
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Unique opening / closing mechanism that can measure even in narrow places*AC / DC both 10A / 100A 2 range switching Φ45mm CT inner diameter*RMS value measurement that can accurately measure even distorted waveforms
-
Product
Current / Voltage input Panel meter with output options
DM3420
-
The DM3420 panel meter accepts Voltage and Current process signals and displays the process value on a high efficiency daylight readable LED display. A built in transmitter power supply is also provided.
-
Product
Cryogenic Current Comparator (CCC)
6200A
-
Measurements International Ltd.
Introducing the Model 6200A Cryogenic Current Comparator Bridge (CCC) from Measurements International (MI) – the ultimate solution for achieving the highest level of resistance calibration accuracy. With an uncertainty of less than 3 parts in 10-9, our CCC surpasses all other technology on the market.
-
Product
AC/DC Clamp Meter
CM4374
-
• AC/DC Clamp • True RMS • 600/2000 A range • V, A, Hz, Ω, and other extensive measurement parameters • Inrush current • Max/Min/Avg/Peak • Wireless data download to a tablet or smartphone
-
Product
30 Amps, 100 MHz BW Current Probe - AC/DC , 50 Amp Peak Pulse
CP031
-
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
Product
High Output Current Op Amplifiers ≥ 100mA
-
Analog Devices high speed , high output current (≥100 mA) op amps deliver high output current while driving low impedance loads with excellent linearity. Whether it's high output current, low input bias current, wide bandwidth, high slew rate, or low distortion, no one sets more performance standards for next-generation designs with the widest portfolio of leading edge products than Analog Devices.
-
Product
5V30A High Current Lithium Battery Tester
TOB-BTS-5V30A
-
Xiamen Tob New Energy Technology Co., Ltd
8 Channels High Current Lithium Battery Tester For Power Battery Performance Detection
-
Product
High Accuracy 100 Amp Current Probe
HA100
-
The HA100 is a compact clamp-on current probe for smaller loads where compact size is important. Its measurement range is from 0.1 to 100 amps AC and is very small which is ideal for locking inside a crowded electrical panel during monitoring.
-
Product
Clamp Meter, True RMS, 100 A AC, 600 V AC, 600 V DC, 17 mm Jaw Opening Max.
72-2985
-
The 72-2985 from Tenma is a mini clamp meter in orange and grey colour. It features high reliability, safety precision and compact design. Its resolution ratio is 1mA, maximum range has maximum range of 100A AC/DC, particular VFC start mode. Entering this mode can accurately measure voltage and current which has VFC frequency conversion. Voltage or current response display is true valid value. Whole range overload protection, reliable measurement accuracy and unique appearance design makes it an outstanding new generation functional electrician/electric power measurement instrument. This complies with EN 610101-1, 61010-2-032, 61010-2-033, pollution degree 2, measurement category: (CAT II 600V, CAT III 300V) and double insulation standards. Conforms to UL STD. 61010-1, 61010-2-032, 61010-2-33 certified to CSA STD. C22.2 NO. 61010-1, IEC STD 61010-2-032, 61010-2-033.
-
Product
Current Measurements of PWM or Inverter, AC/DC 10～200A, φ24mm
CTF-200DC
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*AC/DC 10～200A*Current measurements for PWM or inverter
-
Product
Integrated Two-Stage Current Sensors
-
If ultra-low noise performance is required, our integrated two stage devices are the number one choice. With input inductances from 24 nH to 1.8 µH and a flux-noise level as low as 0.8 µPhi0/sqrt(Hz) an energy resolution of about 45 h is attained. The devices consist of a 16 SQUID series array as amplifier stage and a single front-end SQUID.
-
Product
Oscilloscope Module, Clamp Meter Lead, Digital Multimeter
72-9185
-
The 72-9185 is a Clamp Meter Lead for use with digital multimeter.
-
Product
Current Signature Analysis
-
The Iris Power MDSP3 uses the Current Signature Analysis technology which relies on the concept that faults in the induction motor rotor or driven components result in changes to the rotor magnetic field pattern. Unique magnetic rotating fields are produced due to the faults which induce detectable stator current components indicative of the fault.
-
Product
Current Amplifier/Generator
ULCA-1
-
The Ultrastable Low-noise Current Amplifier ULCA-1 is designed to fulfill the needs of high-accuracy low-current generation and measurements in the range from 1 fA to 1 µA (licensed by PTB).
-
Product
For Overhead Distribution Line Current Tester With Power Flow Direction Record
MHR-600
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Measuring and recording the average current values & power flow directions in the setting interval.・Easy to use, as an indirect hot-line work tool.・Memorized data can be outputted to USB memoryafter measurement.・For 6.6KV circuit, protection level IP64.
-
Product
Power Clamp Meters
-
Precision Mastech Enterprises Co.
Advanced electrical testing tools with hinged, jaw-like clamps that measure AC/DC current, voltage, power (kW), power factor, and harmonics in live conductors without breaking the circuit.
-
Product
Clamp Meters
-
Fujian Lilliput Optoelectronics Technology Co., Ltd.
We are one of the leading and professional clamp meters manufacturers and suppliers in China. Thanks to our highly qualified experts and advanced technology, we are also one of the world's leading brands. Welcome to buy the quality, cheap and durable clamp meters in stock from us. Check the quotation with us now.
-
Product
Earth Ground Clamp Meter
T2000
-
T2000 is a professional clamps specially developed to evaluate resistance of earth rods with no need to disconnect any part of the system (STAKELESS METHOD)
