ESD Monitors
-
Product
Environment Monitoring System
ENVIROMUX-2D
-
The ENVIROMUX-2D supports 2 external configurable sensors, 5 digital inputs, and 1 output relay for control of external devices. It features 2 USB ports for USB modem, USB flash drive, or USB LCD screen. Linux inside.
-
Product
Monitor / Annunciator
RTP-1
-
The RTP-1 Monitor is a general purpose annunciator. Designed for 19 “ rack installations, the RTP-1 is complete with a noise immune filter. The ten point RTP-1 features latching memory. Easy to install and easy to operate, this low power monitor has front panel plug-in replaceable LEDs for indication and a single system Test and Reset buttons.
-
Product
Environmental Noise Monitoring System
E-Box POWER
-
The POWER version of the E-Box is designed with endurance in mind. You are able to customise your power supply and even add Solar Panels for long-term measurements, so you can rest assured this E-Box gives you the POWER you need to perform!
-
Product
Fume Hood Monitor
FHM10
-
Fume hoods are a primary source or protection in laboratories. Face velocity measurements are often used to gauge the performance of a fume hood’s ability to contain and exhaust hazardous chemicals. By accurately measuring face velocity and alarming on unsafe conditions, TSI’s FHM10 Fume Hood Monitors provide a high level of fume hood safety. And, the FHM10 helps users comply with standards and regulations set forth by OSHA, NFPA, ANSI Z9.5, and SEFA, calling for monitors to be installed on fume hoods.
-
Product
Electromagnetic Environment Online Monitoring Systems
OS Series
-
Beijing KeHuan Century EMC Technology Co,.LTD
Beijing KeHuan Electromagnetic Environment Online Monitoring Systems
-
Product
End-to-End Network Monitoring
OSIX
-
Network monitoring with tracing and troubleshooting capabilities to achieve first-class customer experience and to proactively prevent network and service quality degradation. OSIX Monitoring enables Communication Service Providers (CSPs) to detect and resolve network issues or poor performance before end-customers are affected.
-
Product
Monitoring
-
DVB-C, DVB-T/T2, DVB-S/S2 and Analog TV remote monitoring. DAB and FM Monitor permanently monitor the quality of DAB/DAB+, analog FM and RDS signal.
-
-
Product
20Hz Injection Kit Monitoring System
-
Signals & Systems India Private Limited
The Display used to monitor the 20Hz and 50Hz current passing through NGT transformer. This could help to monitor the stator earth fault and could record the current every minute. The current shall be displayed in milliamps for both 20Hz and 50Hz. If an earth fault occurs in the generator star point, the 20 Hz voltage drives a current through the fault resistance. The current can be measured using clamp-on CT which would be clamped between load resistor and NGT. It gives an indication of the current values are lower or higher than the set threshold.
-
Product
SparkFun Single Lead Heart Rate Monitor
AD8232
-
The AD8232 SparkFun Single Lead Heart Rate Monitor is a cost-effective board used to measure the electrical activity of the heart. This electrical activity can be charted as an ECG or Electrocardiogram and output as an analog reading. ECGs can be extremely noisy, the AD8232 Single Lead Heart Rate Monitor acts as an op amp to help obtain a clear signal from the PR and QT Intervals easily.
-
Product
Vacuum Process And Chamber Environment Monitors
-
Our process monitors are innovative in-situ process monitoring instruments that are fully integrated, application-specific packages, including component residual gas analyzers (RGAs), analytical equipment, and control software. Process mass spectrometers are used in varied applications, including; Semiconductor, Thin Film (CVD, Etch, PVD and degas), pharmaceutical lyophylization and bulk gas purity monitoring.
-
Product
21.5" 16:9 P-CAP Touchscreen Monitor
USC-M20
-
21.5" TFT LCD with LED backlight, 16:9 aspect ratio with 1920 x 1080 resolution, Default with P-CAP touch (non-touch option available). IP65-rated front panel, VGA/HDMI connections, VESA 100 x 100 mounting available, Designed with metal enclosure and aluminum bezel.
-
Product
Vaccine Temperature Monitoring System Data Logger
VTMS
-
MadgeTechs Vaccine Temperature Monitoring System (VTMS) is ideal for the continuous measurement and data logging of temperature sensitive vaccines or pharmaceuticals in refrigerators, freezers, and coolers. The system includes a NIST traceable RFTCTemp2000A data logger with thermocouple, Glycol bottle and a power supply.
-
Product
Monitoring System
TriGas X5000
-
The TriGas X5000 Monitoring System is an integrated gas detection solution that helps plant operators comply with NFPA 820. The system monitors for combustible gases, hydrogen sulfide and oxygen with on-board alarming and communication interface to plant and remote location control stations.
-
Product
Solar Monitoring Stations
-
EKO Instruments unique Solar Monitoring Station (SMS) is the primary reference to collect high quality solar irradiance data on-site. The innovative turn-key system provides all fundamental solar radiation and meteorological parameters for PV site evaluation, performance monitoring and cell optimizing.
-
Product
Indoor Air Quality Monitors
-
Maintaining proper indoor air quality (IAQ) has only become more important in recent years as personal health and comfort have become a higher priority than ever before. Our testing and monitoring instruments for IAQ, including our indoor air quality monitors, gas monitor, and odor meters help industrial hygiene and HVAC professionals test and monitor environments to solve crucial air quality problems.
-
Product
GreenEye Monitor
Residential
-
The GreenEye Monitor (GEM) is a multi-channel energy consumption monitor. The GEM is used to measure consumption of up to 32 electrical circuits and provide up to the minute consumption data.
-
-
Product
Full Bandwidth Monitoring
Bluehorn System
-
When reproducing complex sounds, pattern relationships matter just as much as amplitude and frequency. Perfectly linear acoustical output requires phase re-alignment of the input signal. But thanks to the laws of physics, even the most accurate acoustic systems have introduced phase anomalies—until now.
-
Product
Charge Plate Monitor
-
The electrostatic resistance of electronic devices is declining, and the number of ionizers installed is increasing. Ionizers cause deterioration of static elimination performance and imbalance of ions due to dirt and wear of the discharge electrode needle. Charging of electronic devices is also caused by ion blow. of an ionizer that is out of balance due to dirt and wear, and reaches a level that destroys advanced electronic devices.The atmospheric ion monitor measures the potential of the charging plate (detector), which has almost the same capacitance as the device's ground capacitance , with high accuracy, and is the most suitable measuring instrument for checking the effect when installing the ionizer and for daily management.
-
Product
TDR Structural Health Monitoring
-
Material Sensing & Instrumentation
MSI Time-Domain-Reflectometry (TDR) Structural-Health Monitoring probes the structural health of a composite part by propagating a fast electrical pulse along a distributed linear sensor which has been fabricated directly in the laminate. The sensor is formed from the native graphite fibers already used in composite manufacture, and constitutes zero defect. Fibers are patterned into a microwave waveguide geometry, or transmission line, and interrogated by a rapid pulse as shown below. Structural faults along the line cause distortions in waveguide geometry, producing reflected pulses similar to radar. Cracking, delamination, disbonds, moisture penetration, marcelling, and strain are all detected by propagation delay, for sensor lengths up to several meters.
-
Product
OCM-C C-band Optical Channel Monitor
-
Optical Wavelength Laboratories
Features include: user-definable optical power threshold, selectable channel spacing (50 & 100 GHz), and data storage.Data can be viewed either as a bar graph or in tabular format, and the LCD display will automatically rotate based on the orientation of the OCM unit. Viewing in landscape mode allows for more viewing detail.
-
Product
Heavy Duty Vibration Monitor
VUM-800
-
Features • Heavy-duty sensing probe • DPDT 10 amp relay • Optional 230 VAC operation • Control unit remotely mounted • Failsafe operation
-
Product
Dual Wide Range Power Monitor
LTC2992
-
The LTC®2992 is a rail-to-rail system monitor that measures current, voltage, and power of two supplies. It features an operating range of 2.7V to 100V and includes a shunt regulator for supplies above 100V. The voltage measurement range of 0V to 100V is independent of the input supply. Two ADCs simultaneously measure each supply’s current. A third ADC monitors the input voltages and four auxiliary external voltages. Each supply’s current and power is added for total system consumption. Minimum and maximum values are stored and an overrange alert with programmable thresholds minimizes the need for software polling. Data is reported via a standard I2C interface. Shutdown mode reduces current consumption to 25μA typically.
-
Product
Complete Network Monitoring
TiSCADA
-
After years of advanced Research, laboratory and on-field tests, Techimp has developed powerful and effective tools which can help asset managers to take critical decisions and manage power plants in a cost saving ways. Ti-SCADA implements a Real Time condition control of your asset, through a powerful Human Machine Interface (HMI) fully configurable, web based, displaying graphs, charts, trends, KPI, historical data, alarms and customizable reports. Ti-SCADA is a fundamental component of the new generation of Techimp on line condition monitoring systems. Ti-SCADA is designed as a Service Oriented Architecture (SOA) based on interoperability standard for industrial automation - OPC-UA - allowing high performance asset management solutions, tailored on customer needs, to be implemented.
-
Product
Energy Monitoring
-
Our Energy Monitoring products keep you well-informed of how much power you use, what your major loads are, when you use electric power the most, how much you pay for it, and the quality of the power you use. Use these Energy Monitoring hardware and software products to improve your equipment productivity and life, reduce your power use and its costs, and increase your company's profits.
-
Product
Systems For Monitoring And Managing Multiservice Networks
-
Designed to obtain information about the state of the network in operation. The system allows you to organize the protection of operated equipment or other important facilities. The system is open and allows you to increase the necessary functionality as the operator's business develops. Used in optical and coaxial networks.
-
Product
Waveform Monitors
LV5600
-
The LV5600 is a hybrid-type waveform monitor compatible with 4K/HD/SD SDI signal and IP signal.
-
Product
Condition Monitoring
-
Condition Monitoring by TP - generator, turbine, and transformer condition monitoring
-
Product
CO2 And H2O Monitor
EGA30
-
A highly stable monitoring system that measures CO2 to 1ppm in a range of 0-2000ppm, and H20 to 1% relative humidity in a range of 0-100% relative humidity. The instrument is designed for long-term monitoring.
