ATX Power Supply Testers
checks Advanced Technology eXtended power supplies.
See Also: Power Supply Testers
-
Product
Power Supply Systems
-
The Auxiliary Power Unit (APU) serves as a cost effective solution for a variety of military vehicle platforms including main battle tanks, self-propelled howitzers, tactical vehicles, and other special purpose armored fighting vehicles. Our family of heavy-duty, automotive APUs for military applications are packaged to meet specific installation requirements and are available as stand-alone units or may be integrated with any combination of life support systems. Each system provides the following capabilities:
-
Product
Receptacle Tester
RT500
-
Designed to detect the most common wiring problems in standard 120V receptacles.Test for correct wiring, open ground, reverse polarity, open hot, open neutral, hot and ground reversed.Conditions NOT indicated: Quality of ground, multiple hot wires, combinations of defects, reversal of grounded and grounding conductors.Large light indicators for greater visibility.Reinforced prongs for increased durability.Push-pull design with slip-resistance ribbing.Made in USA of U.S. and imported parts.
-
Product
Hardness Tester
-
Shenzhen Graigar Technology Co.,Ltd.
Hardness Testing. Hardness is a characteristic of a material, not a fundamental physical property. It is defined as the resistance to indentation, and it is determined by measuring the permanent depth of the indentation.
-
Product
PICMG® 2.11 47-Pin Hot-Swap Redundant 3U CompactPCI® 8HP 250 W Power Module
cPS-H325/48
Power Module
- PICMG® 2.11 CompactPCI® Power Interface compliant- 3U CompactPCI® 8HP form factor- PICMG® 2.11 47-pin CompactPCI® in-rack power module interface- 250 W DC output- Active PFC (Power Factor Correction) meets IEC1000-
-
Product
High-Performance Autoranging DC Power Module, 60V, 17A, 500W
N6756A
Power Module
The Keysight N6756A is a 500 W high-performance, autoranging DC power module that provides low noise, high accuracy and programming speeds that are up to 10 to 50 times faster than other programmable power supplies. Optional high-speed test extension offers an oscilloscope-like digitizer that increases measurement accuracy when viewing high-speed transient or pulse events within the device-under-test (DUT).
-
Product
Inductor Tester
-
An impulse can be applied to the coil of a chip power inductor to perform insulation tests (surge tests) within the windings.
-
Product
10 MHz To 67 GHz USB Wide Dynamic Range Peak And Average Power Sensor
U2067XA
Power Sensor
Accurately measure any modulated signal with the Keysight Technologies, Inc. U/L2050/60 X-Series wide dynamic range power sensors. The USB/LAN connectivity models come with a wide dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with a super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the internal zero and calibration function. The U/L2050/60 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming. Simply connect the sensor to your PC installed BenchVue BV0007B Power Meter/Sensor Control and Analysis app to perform average power measurement and analysis.
-
Product
Stationary Industrial And Railway Power Supply
-
For decades, Gustav Klein has been supplying safe power supplies for industry and railways, such as rectifiers, inverters, DC converters, UPS and BSV systems, as well as frequency converters with a fixed output frequency.
-
Product
Power & Energy
-
In order to strengthen energy management and monitoring, Advantech offers high quality energy monitor and solution-ready products for the Power and Energy Automatic Management applications. There are three categories of products: Energy Computers, Energy Controllers and Energy Data Acquisition modules. All the components fulfill the highest demands for harshest environments of the Power Industry.
-
Product
Low Voltage Power Supply Solutions
-
AC-DC Configurable. Advanced Energy is proud to offer highly reliable and cost-efficient low voltage power supply solutions. The Excelsys low voltage power supply product line has more than 20 years of experience of engineering power-density rich and extremely efficient supplies for a variety of markets.
-
Product
AC/DC Power Supply 20 W
CFM21M120-S
-
AC/DC power supply with 20 W from Cincon | input ranges 90 - 264 VAC | output 12 V | operates in temperature from -25 to +70 °C | provides 2 MOOP safety and is class II | screw terminals
-
Product
Fiber Amplifier - Node With Supply
FANS 811-812
-
- AGC - Automatic Gain Control- Higher RF at next connected Node- Maintain MER/BER for Digital FTTH Transmission- High Quality DFB Lasers with Isolators- Variable SLOPE/GAIN Control- Input Wavelength : 1310/1550nm- Output Wavelength : 1310nm- Digital Display of Optical Level- External FusesPower Options :- Mains 220VAC, 50Hz- 12V DC / 2 Amp- 40VDC from “40V/RF out” connectors
-
Product
PWM Type AC Power Supply
LSP-5KVA
-
• Circuit Type: (IGBT) MPWM Pulse Duration Modulation • Input: 1 Phase 220V±10%, 50Hz/60Hz±5% • Output Voltage: HIGH/LOW Adjustable 1)1 Phase Voltage Range: (HIGH)0～300V, (LOW)0～150V 2) Nominal Voltage: +10%～+25%, -10%～-30% • Output Frequency: 50Hz, 60Hz, adjustable between 45 and 70 Hz, 400Hz • Load Voltage Stabilization Rate: ≦0.5% • Frequency Stabilization Rate: 0. 1% (Fix Point 50Hz, 60Hz and 400Hz) • Wave Distortion Rate: ≦2% (Resistor Load); Efficiency: ≧85% • Output Instruments: Frequency Indicator, 4-digits RMS digital frequency indicator, resolution is 0.1Hz Voltage Meter, 4-digits RMS digital voltage meter, resolution 0.1V Ampere Meter, 4-digist RMS digital ampere meter, resolution 1Ma Power Indicator, 4-digits RMS digital power indicator, resolution 1W Power Factor Meter Resolution 0.001 • Protective Devices: Over load, short circuit, over voltage, over current, over temperature protective and alarm devices • Operating Environment: Temperature 0～40℃ Relative Humidity 0～90%
-
Product
Power Solutions
-
Applied Research and Technolgy
Power your performance with advanced protection and filtering.
-
Product
Moisture Testers
-
Wuxi IMHOO Technology Co., Ltd.
Used to measure the percentage of water in materials like wood, drywall, concrete, and soil.
-
Product
Adhesion Testers
-
Instruments for measuring the adhesion of coatings to metal, wood, concrete and other substrates.
-
Product
Chip Tester
TL2000
-
ficonTEC’s series of testing machines is focused on automated electro-optical characterization ofsemiconductor chips. The ficonTEC TL2000 is a fully automated test and inspection system for unmountedlaser diode bars, single chips and chips on submounts.
-
-
Product
Power Meters
SX1100
-
Frequency range:S1 (1.8-160MHz)S2 (430-450MHz/800-930MHz/1240-1300MHz)Power display range:5W/20W/200WAccuracy at full scale:±10% (F.S.)Minimum power at SWR
-
Product
Low Side, 200 MHz, 100 PA – 20 MA
CX1103A
Power Sensor
The CX1103A low side current sensor is a dedicated accessory for the CX3300 series mainframe and features the series widest stand-alone bandwidth up to 200 MHz
-
-
Product
40kw High Efficiency AC/DC Power Supply Charger 100-750VDC Charging Rectifier 100A Battery Charger
SD750100G
-
Zhejiang Sandi Electric Co., Ltd
40kw High Efficiency AC/DC Power Supply Charger 100-750VDC Charging Rectifier 100A Battery Charger is for DC battery system charging station. With three-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. 50-500Vdc output voltage range optional, suitable for all types of batteries.
-
Product
Franklin Tester
Model FT1
-
The Franklin tester FT‐1 is designed to measure the surface insulation resistivity of electrical steel sheet according to the ASTM Standard A717 and IS:649. This test method is suitable for quality control in the application of insulation coating. For ease of testing FT‐1 automatically set 300 PSI pressure on the sample by the inbuilt hydraulic unit and it is capable to set the desired test temperature of the platform. Then the regulated supply of 0.5V gets on and the current flowing through the insulation get measured. The calculated insulation resistivity will be displayed on graphics LCD display and as well as on printed report via thermal printer.
-
Product
Programmable DC Power Supply
CBCT
-
The CBCT is a variable voltage DC power supply designed specifically to test substation circuit-breaker Open and Close coils. The CBCT uses the substation’s DC power supply to electronically generate a programmable output voltage from 5% to 95% of the source voltage. The CBCT can maintain up to an 80A test current while maintaining 2% or better voltage regulation during the circuit breaker coil operation.
-
Product
Power Sources
-
EPOS 340 is the multi-functional three-phase generator which comes into its own whenever maximum power and high signal accuracy are required.Intelligent amplifier technology and fully synthetic signal generation make it possible to issue any signal shape across a wide frequency range or even to play back complex transient signal characteristics. EPOS 340 is designed for use as a stand-alone device or for operation with an external PC.
-
Product
Power Modules
-
VadaTech offers high density AC or DC input power modules with up to 95% power efficiency in single module and double module variants to accommodate different power needs. We also offer specialty modules such as extended full, block format for specific chassis types.
-
Product
Speedometer/Taximeter Testers
-
Machines for checking the accuracy of speedometers, taximeters, speed limiters, speed warning devices. As with most VLT equipment, these machines can be used stand-alone, or in an integrated test lane.
-
Product
Power Induction Tester
MIG-ITU-K44
-
The MIG-ITU-K44 is designed for power induction testing at line frequencies of 50 and 60Hz. Power induction tests need only be performed at the frequencies of the public power supply or railway power of the country of application. Basic and enhanced level tests can be performed according to ITU-T K44.
-
Product
Power Meters
-
The Krytar Model 9000B is a low cost, high performance CW power meter using a diode based power sensor. The power meter can measure power levels from -39 to +20 dBm and cover frequencies from 100 kHz to 40 GHz. With bench and field service applications in mind, the power meter was designed to be completely portable. The power meter can be used for swept measurement.
-
Product
Power Meter
P-Series
-
The N8262A is a compact and slim LXI-compliant P-Series modular power meter. The N8262A helps you to reduce your test system size and enables LAN-based automated power measurements. Owing to LXI test standardization and its interoperability with existing test assets, your system can be up and ready in no time.
