GPS Simulators
-
Product
LED Solar Simulator
LumiSun-50
-
The LumiSun-50™ is a high power, multi-wavelength LED solar simulator that meets IEC 60904-9 Class AAA for spectral match, uniformity of irradiance, and temporal stability. The LumiSun-50 achieves a spatially uniform illumination field from a chip-on-board (COB), multiple-wavelength LED die array. The field of illumination is 50 x 50 mm at a working distance of 200 mm. The LumiSun-50 includes a driver/controller which individually provides constant current to each die in the COB array. Total irradiance of 1.1 sun units is provided and can be decreased to 0.1 suns. The LED light source of the LumiSun-50 is contained within an air-cooled housing that can rotate the angular beam alignment. Adjustment and setting of the optimum light path working distance is visually facilitated by a converging pair of red dot laser pointers.
-
Product
SIMulation Workbench
-
A comprehensive framework for developing and executing real-time hardware-in-the-loop and man-in-the-loop simulations.
-
Product
2 PRI + 32 BRI-S/T ISDN Simulator
CH-32BRI-ST-MOD-2PRI
-
This unit has two PRI ports and 32 BRI ports allowing ISDN equipment to be connected together just as if they were connected through the ISDN network
-
Product
Partial Discharge Simulation Devices
-
Hangzhou Xihu Electronic Institute
Simulation device of cable PD faults, simulation device of switchgear PD faults, simulation device of GIS PD faults, simulation device of transformer PD faults.
-
Product
GPS Amplifier/Splitter
-
The amplifiers has typically 40 dB of gain while the splitters can split an antenna from 4 to 20 ways.
-
Product
Incremental Encoder Simulator
ENC-SIM01
-
Plant Control and Automation Pty Ltd
This instrument is designed to simulate the function of most types of incremental encoders; it allows the engineer to fully test a control system that uses a rotary or linear shaft encoder, without the need for any mechanical movement.
-
Product
ARINC825 (CAN Bus) Test & Simulation Module for VME With 4, 6 Or 8 CAN Bus Nodes
AVC825-x
-
ARINC825 (CAN bus) Test & Simulation Module for VME with 4, 6 or 8 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The AVC825-x VME card can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
Product
Modular Solar Array Simulator Mainframe, 1200W
E4360A
Mainframe
The Keysight 1200W, E4360A Modular Solar Array Simulator is a 2U high, 2-slot mainframe that accepts up to 2 E4360 series modules. Modules are ordered separately. It offers LAN, USB, and GPIB interfaces standard.
-
Product
Digital And Analog Call Simulation
-
GL’s T1 E1/Analog Test Suite supports analysis and emulation of legacy protocols (MFCR2, E&M, SS1/SS4, SS5, Voice Call Signaling, 2-wire Call, SF Signaling (DTMF)) applicable to Federal Aviation Administration "FAA" within their National Airspace System "NAS" Ground-to-Ground Air Traffic Control Network and Voice System (NVS) to Analog Interphone.
-
Product
ARINC 429 Test And Simulation USB Module
USB-429
-
*4, 8 or 16 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*Sorting according to SDI field*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
Product
Hybrid Vehicle Battery Simulator and Test System
-
Winner of the SAE 2008 Technical Award for Hybrid Vehicle Testing Technology, SAKOR Technologies Hybrid Vehicle Battery Simulator and Test System is designed for simulating high-voltage batteries in an electric drivetrain testing environment as well as directly testing high-voltage batteries and charging systems.
-
Product
LXI Simulation Tool
60-901-001
-
This tool will simulate all of our PXI & LXI switching products and most of our PXI simulation products allowing for code development independent from your application hardware
-
Product
GPS Signal Splitter 16 Way, SMA Jack, 1 - 2 GHz, 50 Ohm Coaxial
GPS161
-
INSTOCK Wireless Components, Inc
Wideband Frequency (1000-2000 MHz)Low Insertion Loss (0.6 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)15 VDC & 75 mA Max on DC Block PortsTri Alloy SMA Female (Jack) Low PIM
-
Product
AFDX ® / ARINC 664 Test And Simulation PCI Module
PCI-C664
-
*Supports IEEE 802.3 10/100/1000 Mbit / s full duplex Ethernet connections*Uses SFPs to support both electrical and optical interfaces*Half-size PCI / PCI-X modules*Simulates multiple AFDX® / ARINC 664 end systems*Standard Ethernet processes simultaneous with ARINC 664*Up to 128 output VLs and 512 input VLs*Upper layer protocol handling (ARINC 653, UDP, IP) managed onboard*DMA for high data rate applications*Windows XP / 7, Linux, and LabVIEW Real Time Drivers & APIs (others on request)*Easy to use tool for configuring AFDX® / ARINC 664 end systems (XML based)
-
Product
MIL-STD-1553 Test & Simulation Interface for VME
VME-1553
-
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurationsTransformer & Direct Bus Coupling - Concurrent Bus Controller, 31 Remote Terminals, & Bus Monitor operation - Full error injection and detection - Multi-level trigger for capture and filtering - IRIG-B time code encoder/decoder - Ten high voltage (up to 30V) programmable DIO lines - Real-Time recording and physical bus replay - ANSI Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, & VxWorks (others on request) - Designed for extended temperature operations - 64-bit VME Interface (VME master & slave capability) - Front Panel and Rear I/O (P2) Available
-
Product
Patient Simulator
-
Fluke Biomedical ProSim Vital Signs Simulators transform physiological simulation by adding multi-parameter functionality (including ECG, SpO2, temperature, respiration, NIBP, IBP, cardiac output, and fetal ECG/IUP) in a single patient simulator device, helping you meet your patient monitoring system testing and medical device quality requirements to ensure patient safety.
-
Product
Simulation Transport Vibration Table
CX-M120
-
Shenzhen Chuangxin Instruments Co., Ltd.
CX-M120 Simulation Transport Vibration Table was applicable to toys,furniture,gifts,cera-mics,packaging and other products to simulate the transport tests.Comply with the U.S. and European transport standards and have characteristic with low noise,reasonable structure,durable,etc.Basic Standard:Following The EN.ANSI.UL.ASTM.ISTA International Trans-port Standard.
-
Product
Large Area Solar Simulators
-
The LASI Beam Turner assembly allows the output of the LASI to be projected horizontally. It attaches to to the standard LASI downward facing stand that is included in the base LASI system.
-
Product
Environmental Simulation Testing
-
MET's Environmental Simulation Labs, on both coasts, employ numerous environmental chambers, including several large walk-in chambers. Hydraulic and electro-dynamic shakers are used for a wide range of vibration testing, from ISTA packaging to seismic compliance testing. MET's hydraulic vibration systems are capable of full level (Zone 4) seismic simulation.
-
Product
PXI/PXIe Analog Output/Current Loop Simulator Module - 8 Channel
43-765-003
Analog Output Module
The 41/43-765-003 is an 8-channel Analog Output Module designed to meet the requirements of industrial control applications utilising current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signalling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
Product
68HC11E Simulator
SIM11E
-
Simulate your M68HC11 microcontroller designs on your personal computer. Helps find hidden errors easily and efficiently.
-
Product
Multi-Spool Network Simulation & Latency Solutions
Fiber Lab 750
-
from M2 Optics provides the perfect combination of flexibility and efficiency when requiring spools of fiber for testing, latency, and system demonstration applications.
-
Product
6 Channel Function Generator / Flow Simulator
DP-cPCI-2601
-
DP-cPCI-2601 is a 6 Channel 2MS/s Waveform Generator with high frequency performance, versatility and compact size in an economical cPCI bus format. Signal output in the range of 10 mHz to 5 KHz with 14 bit vertical resolution makes this single slot, 6U-sized cPCI card a powerful solution to meet most demanding test stimulus.DP-cPCI-2601 uses Direct Digital Synthesis (DDS) technique to generate stable and accurate output waveforms down to 0.01 Hz resolution. DP-cPCI-2601 offers Sine, Square, Ramp, Triangle, Pulse as built-in wave shapes and user defined arbitrary waveform.DP-cPCI-2601 can frequency sweep any of its function outputs. User can sweep upwards using linear sweeps.
-
Product
STANAG3910/EFEX Test And Simulation Module for Standard Ethernet
ANET3910
-
STANAG3910/EFEX Test and Simulation module for Standard Ethernet. The ANET embedded Linux Operating System gives the unique capability to run the optional PBA.pro Engine right in the box. Another option is the ANET-ADK onboard software development kit where users create run-time applications (e.g. STANAG3910/EFEX to Ethernet Converter, STANAG3910/EFEX to Ethernet Gateway) to execute right in the box. For wireless applications, an ANET compatible USB Wifi dongle is optionally available.The capability to execute Python scripts in the ANET is a standard feature. For applications with multiple ANET devices AIM offers the ADock ANET Docking Station to host up to 4 ANET modules.
-
Product
Precision Thermo-Mechanical Simulators For Materials Testing Excellence
500 Series
-
Industry-leading thermo-mechanical physical simulation systems engineered for researchers and manufacturers who demand accurate, repeatable materials testing
-
Product
Solar Array IV Curve Simulation Softpanel
-
Chroma Systems Solutions, Inc.
Easily program the I-V curve of the Solar Array Simulator with this test software as well as the I-V and P-V curves for real-time testing. See both dynamic and static MPPT efficiency and even simulate the IV Curve with shadows. The real world weather simulation function allows the user to simulate the irradiation intensity and temperature level from early morning to nightfall.
-
Product
FIber Based Solar Simulator
-
Provides up to 12 suns class B non-uniformity over a 12.5 mm diameter with the A4 Light Line and class C uniformity can be achieved over 18mm diameter both with a working distance of 25 cm. Provides up to 4 suns class B non-uniformity over a 12.5 mm diameter with the A1 Light Line with a working distance of 25 cm.
-
Product
Electronics Cooling Simulation Software
FloTHERM
-
Perform thermal analysis, create virtual models, and test design modifications of electronic equipment before physical prototyping. FloTHERM uses advanced CFD techniques to predict airflow, temperature, and heat transfer in components, boards, and complete systems, including racks and data centers. It''s also the industry''s best solution for integration with MCAD and EDA software.
-
Product
Mouth Simulator
BO1032
-
As consumers demand smaller devices that produce better sound and need better microphones, you need to test your microphones using more than a simple 1kHz tone. Sweep tests require a good mouth simulator that can produce a sweep with a known steady SPL.
-
Product
GPS, GLONASS, Galileo Splitter 2 Way, TNC, 1000 - 2000 MHz, 50 Ohm, Passive
GPS220
-
INSTOCK Wireless Components, Inc
GPS L1 - L5, GLONASS, Galileo splitterLow Insertion Loss (0.2 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)15 VDC & 75 mA max on DC block portTri Alloy TNC Female (Jack) 50 Ohm
