Broadband Power Amplifiers
-
Product
Dining Isolation Amplifier
-
Knick Elektronische Messgeräte GmbH & Co. KG.
To feed and Isolation of 2-wire transmitters / sensors or SMART transmitters with HART transmission. Working voltage up to 2500 V AC / DC. Available for hazardous and non-hazardous area.
-
Product
High Voltage Amplifier
HA-405
-
* 400Vp-p(±200V DC)* 400mAp-p(±200mA DC)* Bandwidth: ≦1MHz(200Vp-p) *Slew Rate: 500V/us *Gain(AMPL):0~90(10 Turn VR) *DC Offset: ≦0~±200V(10 Turn VR+SW) *Output Resistor: 50Ω *Microprocess Control Protection
-
Product
Composite 1×6 Video Distribution Amplifier
VDA106
-
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
Product
Active broadband antenna up to 6GHz
Series HyperLOG ® 70 X
-
Compatible with any Spectrum Analyzer or Oscilloscope. Incl. High-End Preamplifier. Ultra high gain (44dBi). The HyperLOG X LogPer antenna series can be used to locate extremely weak signals, thanks to the integrated preamplifier. The antenna offers excellent directional characteristics which can be optimized using theoptional Laser and Compass.
-
Product
Power Potentiostat/Galvanostat
1100C
-
The Model 1100B series power potentiostat/galvanostat is designed for electrochemical applications that require relatively large current and high compliance voltage, such as battery studies, corrosion, electrolysis, and electroplating. The current range is 2 A, and the compliance voltage is 25 V. The instrument contains a high speed digital function generator, a fast data acquisition system, filters for current signals, iR compensation circuitry, a potentiostat, and a galvanostat (Model 1140B). The potential control range is 10 V.
-
Product
40~860 MHz Trunk Hybrid Amplifier
AS 1616
-
Hybrid Amplifiers used in Trunk and branch lines specially designed to serve the needs of cable systems with very Long Trunk Cables. They are in Aluminium Housing providing maximum heat dissipation and have RFI Shielding. They incorporate superior quality Hybrid IC Module to obtain excellent features.- Frequency Range: 40 ~ 860 MHz- Mains cum Power Pass- Output Level: 102 dBµV- Level Flatness: ±0.75 dB- 32 dB Gain (40 dB Optional)- Optimum for Trunk Distribution- Superior Quality Hybrid IC Module- Hybrid IC Protected- Voltage Selection LED - for Easy Selection
-
Product
Super Low Noise Amplifiers
WCA Series
-
WCA series super low noise amplifiers have sub-0.5 dB noise figure at VHF band with several octave bandwidth. The amplifiers have 75 Ohm impedance.
-
Product
Digital Quad-Phase "DSP" Lock-In Amplifier -
eLockIn203
-
The eLockIn203 can be used as spectrum analyser, as oscilloscope, as sinus generator or as measurement control system.
-
Product
AC/DC Power Pass Hybrid Amplifier
AS 1313 SMPS
-
- Low Power Consumption - Drive More Amplifiers- Special 6 Volt Module -For High OutputMultiple Power Options:- 12 Volt DC Adapter- DC Power Pass 40V- AC Power Pass upto 110 V
-
Product
Power Supply, 100 V, 50 A, 5000 W
N8759A
-
The Keysight N8759A power supply is a single output power supply in a small 2U package that offers essential features to fit your budget. The N8759A power cable offers flexible AC input options, analog / resistance control of output voltage and current, as well as parallel and series connection of multiple supplies to achieve more output current or voltage.
-
Product
Power Distributions
-
LXinstruments Power Distribution Units (PDU) provide all of the functionality required to power a test system in a compact 19-inch rack. This means that devices can be supplied with both mains voltage and DC voltage. With the soft-on-off function, the PDU can be controlled remotely via remote buttons and other potential-free contacts. We carry single-phase devices for the 16 A connection to three-phase devices for the 3x63 A or for the 125 A connection.
-
Product
Power Supplies
CU-600B
-
The CU-series is a semi-modular power supply that lets you select the cables you need while powering your system at a healthy voltage. Everyone likes a clean and easy installation. This power supply allows you to keep what you want and remove what you don't. While necessary connectors, like the 20+4 pin power connector, are attached to the unit, you decide which of the others should stay. Customize your power supply to reflect your system.
-
Product
E-Series Peak and Average Power Sensor, 50 MHz to 6 GHz
E9321A
-
The E9321A power sensor has a 300 kHz video bandwidth and is ideal for time-gated peak, average and peak-to-average ratio power measurements on TDMA wireless formats such as NADC, GSM and EDGE.
-
Product
Power Bus
MS 1606
-
The PowerBus is used to service printed circuit boards, instruments and systems, which has Micro controller / Microprocessor. The PowerBus has RS232 Communication for PC interface. The PowerBus connects to the UUT through the microprocessor / micro controller socket. The UUTs microprocessor / micro controller is removed from the UUT and it is replaced by the PowerBus. The Power Bus adapts microprocessor specific function as pin layouts, status / control function, interrupt handling, timing and memory and I / O addressability.
-
Product
Low Noise Amplifier
-
R&K’s Low Noise Amplifier (LNA) series products are a type of small signal amplifiers but with excellent noise figure. LNA is designed to significantly minimize additional noise to be introduced inside the product, and capable to amplify the input RF signal to the required level with minimal impact from noise on output RF signal.
-
Product
Low Noise Amplifiers
-
High-intercept and high-gain low noise amplifier modules. Wide supply voltage range. Custom designs available through LNA design services.
-
Product
Power Supply, 40V, 125A, 5000W
N8756A
-
Keysight basic DC power supplies offer essential features for a tight budget. The Keysight N8756A is a 40V, 125A, 5000W, single output power supply in a small 2U package.
-
Product
Broadband Antenna
DRH2
-
Wide frequency range, ideal to complement RF test enclosures for various wireless testing applications
-
Product
Power Energy & Power Quality Analysers
-
Designed for test and maintenance teams working in industrial or administrative buildings can be used to obtain a snapshot of the main features characterizing the quality of the electrical network.
-
Product
Low Noise Amplifier
1010
-
A low noise, DC-coupled amplifier is packaged in a rugged, die-cast aluminum case with BNC connectors enabling input and output. Provides very low voltage noise and current noise in the critical region of 0.1 Hz to 10 Hz making this the ideal amplifier for thermopile detectors in sensitive systems design and laboratory experiments.
-
Product
Amplifier Systems
RF Amplifiers
-
Systems are complete. They plug into an outlet and are ready to go. Our standard systems are 3U, which is 5.25″ and 5U, 8.75″. Systems are available with or without IEEE-488, RS-232 and Ethernet connectivity. Amplifiers Systems are available in both Broadband and Band-Specific frequencies.
-
Product
BG Series Bass Amplifiers
-
250 Watt Bass Combos with Built-In TonePrints and Integrated Tuner.
-
Product
Extreme Low Power Detector Laser Power Meters
11XLP12
-
11XLP12 extreme low power detector is best suitable for low power im both the µW and mW regimes with very low thermal drift. Featuring broadband flat spectral response, minimal thermal drift and a noise equivalent power as low as 1 µW the 11XLP12 is ideally suited for measuring any pulsed or CW low power laser.
-
-
Product
High Power RF Amplifiers
-
Corry Micronics' line of high power RF amplifiers feature up to 40% efficiency. an extended temperature range of -30 degC to 55 degC for MIL-STD applications, and status monitoring signals that provide diagnostic information.
-
Product
CW Power Measurement
-
Measure CW power from 10 MHz to 50 GHz at more than 17,500 readings per second over GPIB. Measure up to 90 dB with a single sensor, and select from a variety of high power sensors up to 50 W.
-
Product
Power, Patchcord, Receiver, 72", Mini Power, 16 AWG White, Single Ended (19 Amps)
7-234916000-072
-
Power, Patchcord, Receiver, 72", Mini Power, 16 AWG White, Single Ended (19 Amps).
-
Product
Power Systems
-
Astronics serves global customers as the aircraft industry’s electrical power experts, offering a breadth of power and motion solutions for commercial transport, business, VIP, rotorcraft, military aircraft, and other airborne platforms. Whatever your program, you’ll find a proven, certified solution with Astronics.
-
Product
VPX55-3HU 3U VPX Power Line Conditioner with Holdu
VPX55-3HU
-
The VPX55-3HU is a 400-Watt DC/DC Power Line Conditioner which plugs directly into a standard 3U VPX chassis with a VITA 62 0.8" or 1.0" power slot. This off-the-shelf solution is compatible with VPX specifications and addresses the need for 3U VPX power applications requiring an optional VITA 62 Energy Storage Module.
-
Product
Amplifier Built-in Ultra-compact Laser Sensor
EX-L200
-
Panasonic Industrial Devices Sales Company of America
The EX-L200, the one of the world’s smallest Laser Sensors with a built-in amplifier, is designed to detect minute objects with utmost accuracy. Despite its miniature size, the Thru-Beam Type (EX-L211) can detect minute objects with a diameter of just 0.3mm, and the Spot Reflective Type (EX-L221) can even detect gold wire whose diameter is a mere 0.01mm. To facilitate solving application tasks, these sensors come equipped with a Potentiometer and two indicator LEDs. For the Thru-Beam Type, reflective material on the receiver allows users to visualize the laser beam, easing beam-axis alignment.
