Diode Testers
See Also: Diode Test
-
Product
SCR Diode Testers
-
SCRs and Diodes are used in the power sections of various power systems. A SCR Diode Tester is an important piece of equipment to determine if a SCR or a diode is defective in a power circuit. It is difficult and time-consuming to troubleshoot SCRs and Diodes with a digital meter.
-
Product
Bypass Diode Tester
BDT
-
Our bypass diode thermal tester is designed to assess the adequacy of the thermal design and long-term reliability of PV modules bypass diodes, which are used to limit the detrimental effects of module hot spot susceptibility.
-
Product
Photovoltaic System Bypass Diode Tester
FT4310
-
Hioki is pleased to announce the launch of the Bypass Diode Tester FT4310 for Photovoltaic Systems. The FT4310, which is designed to test bypass diodes in strings of crystalline photovoltaic cells, can be used to detect open and short-circuit faults in bypass diodes by string either in daylight or at night. The instrument is the first portable device capable of detecting bypass diode open faults in operating panels (without requiring the panels to be shielded from sunlight).
-
Product
Diode Tester
FEC200E
-
Frothingham Electronics Corporation
The FEC200E is an automatic computer- controlled diode and rectifier tester. It is controlled by a standard PC-compatible computer running FreeDOS.
-
Product
Diode Tester
FEC VF40CM
-
Frothingham Electronics Corporation
The VF40CM is intended for testing VF, HALF CYCLE SURGE, and THERMAL RESPONSE/RESISTANCE on small- and medium-power diodes and rectifiers. It can also measure THERMAL RESPONSE/RESISTANCE on NPN and PNP bipolar transistors using an external user-supplied VCB supply.The VF40CM also is sometimes used to measure VZ of low-voltage zener diodes up to the compliance voltage limit of the tester. 20V at 20A is possible.
-
Product
Gearbox Tester
Tester
The gearbox tester was designed to test the Azimuth Drive Unit (ADU) for a missile launcher. The ADU is the horizontal position controller for the launcher. It consists of a main drive shaft, a manual drive shaft and an output drive shaft. This system uses a multi-axis motion controller to operate.
-
Product
KVS Rugged Igniter Tester With Current Monitor
4314
Tester
The Valhalla Scientific Model 4314 KVS Digital Igniter Tester is designed to provide extremely safe and reliable resistance testing of explosive or volatile devices. Proven uses include fuses, squibs, igniters, explosive bolts, automobile airbag initiators and many others.
-
Product
Automated Coherent Receiver Tester
CoRx Tester.
Receiver Tester
Quantifi Photonics’ CoRx Tester provides automated measurement of key coherent receiver performance parameters. The CoRx Tester is comprised of a pre-configured PXI chassis, a two-channel tunable laser, a polarization controller, and a two-channel Variable Optical Attenuator (VOA) with built-in power meter. Just connect the two optical outputs to your Integrated Coherent Receiver (ICR), connect your ICR to the oscilloscope and let the CoRx Tester software do all the rest.
-
Product
Bit Error Rate Tester - MATRIQ
Tester
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
Product
Error Detector Remote Head 32 and 17 Gb/s
N4952A
Bit Error Rate Tester (BERT)
The N4952A is an affordable and compact error detector remote head available in 4 to 17 Gb/s and 5 to 32 Gb/s configurations. Compatible with the N4960A Serial BERT controller, it is the perfect solution to test up to 32 Gb/s per channel for 100 Gigabit Ethernet applications and other high-data rate devices. The N4952A error detector supports PRBS or user patterns and operates up to 32 Gb/s in a single band with no gaps or missing data rates. The remote head allows the test equipment to be located very close to the device under test, eliminating the need for long cables that degrade signal quality.
-
Product
Hoist Tester
Tester
The system has the capability of operating hyraulic powered hoists, DC powered hoists and 400Hz AC powered hoists. When a unit is connected to the system it is automatically detected and the system will load the unit's control software, acceptance procedures and operational safety limits. By doing all of this the operator does not need to worry about anything other than installing the unit and clicking Run to execute a full test procedure.
-
Product
64 Gbaud High-performance BERT
M8040A
Bit Error Rate Tester (BERT)
The Keysight M8040A is a highly integrated BERT for physical layer characterization and compliance testing. With support for PAM-4 and NRZ signals and data rates up to 64 Gbaud (corresponds to 128 Gbit/s) it covers all flavors of 200 and 400 GbE standards.
-
Product
Universal A/V Tester
Tester
This tester was built for our client with the specific requirement that specific UUTs can be added to the system by our client. We handled developing test software for the first 2 UUTs utilizing an open programming structure that allowed programming modules to be strung together to create test programs for any additional UUT that our client wants to add in the future.
-
Product
AXIe M8000 Series of BER Testers
Bit Error Rate Tester (BERT)
Simplified time-efficient testing is essential when you are developing next-generation computer, consumer, or communication devices. The Keysight M8000 Series is the highly integrated BER test solution for physical layer characterization, validation, and compliance testing. With support for a wide range of data rates and standards, the M8000 Series provides accurate, reliable results that accelerate your insight into the performance margins of high-speed digital devices.
-
Product
120 GBd High-performance BERT
M8050A
Bit Error Rate Tester (BERT)
The Keysight M8050A high-performance bit error ratio tester (BERT) enables accurate characterization of receivers used in next-generation data center networks and server interfaces. With uncompromised signal integrity, support for NRZ, PAM4, PAM6, and PAM8 signals, and data rates up to 120 GBd, the flexible architecture of the M8050A supports 1.6T pathfinding as well as other leading-edge technologies.
-
Product
MXE EMI Test Receiver, 3 Hz to 44 GHz
N9038B
Receiver Tester
The Keysight N9038B is a standards-compliant MXE EMI test receiver and diagnostic signal analyzer built on an upgradeable platform. You choose the frequency coverage you need to fully test devices with outstanding accuracy and sensitivity across required ranges.
-
Product
Three-Path Diode
NRPxxS/SN/SN-V
-
The R&S®NRPxxS/SN power sensors use three separate diode paths, each operated in the optimum detector range. As a result, the average power can be determined with high accuracy independent of the modulation type. Measurement results are hardly affected by interfering signals or harmonics.
-
-
Product
TVS Diodes
-
Power TVS diodes provide outstanding protection for both alternating current and direct current power line applications by a Power TVS diode in a surface mount package. When compared to other devices, such as MOVs, power TVS diodes provide much better protection. Bourns provides a broad voltage range of devices with surge current ratings ranging from 3, 6, 10, and 15 kA to suit a variety of applications.
-
Product
PIN Diodes
-
PIN photodiodes convert light to current – without a bias voltage having to be applied. Silicon is commonly used as an inexpensive detector material in the Vis range. For higher demands, InGaAs is used; it covers the widest spectral range from the Vis to the NIR. We offer silicon carbide as a “solar-blind” detector specifically for the UV range.
-
Product
Diode Power Sensor
8481D
Power Sensor
The 8481D diode power sensor measures average power over the frequency range 10 MHz to 18 GHz and power range -70 to -20 dBm (50 dB dynamic range).
-
Product
Diode Submounts
-
Ultra-precise patterning of thin film metals on dielectrics with high thermal conductivity are used for diode submount applications. Via the acquisition of Ion Beam Milling, Inc., SemiGen is the industry leader for laser diode submount fabrication. As each application is different, we work with customers to develop a custom design that perfectly fits their requirements. We have experience producing circuits utilizing substrates of varying thicknesses with high thermal conductivity such as alumina (Al), aluminum nitride (AlN), and beryllium oxide (BeO). SemiGen can deliver laser diode submounts with or without Au/Sn pads depending on your needs.
-
-
Product
Diode Lasers
Spot Creator
-
Advanced Photonic Sciences LLC
Spot Creator is an innovative accessory developed for enhancing the performance of blue laser diode based engraving and cutting machines. Spot Creator solves a major problem with using asymmetric blue laser diodes: the production of engraving features that are different in the X-Y directions, resulting in unequal or blurred lines. Using Spot Creator, line widths are equal in the X-Y directions, with a minimum spot of 50 μm. The intensity on the engraved part is thus maximized.
-
Product
Laser Diode
-
Yisinc Optical Technology Co., Ltd
Laser diode is an efficient radiation source for CW and pulsed operations.
-
Product
Tunable Diode Laser
-
Tunable diode laser absorption spectroscopy (TDLAS) is a fast, accurate, non-contact gas analysis technique that responds quickly to changing analyte concentrations. It is a proven technology free of interferences from other sample stream components.
-
Product
Fast Recovery Diodes
-
We offer high-performance products with low forward voltage (VF) and high-speed reverse recovery time (trr) for increasing device efficiency.
-
Product
Steering Diodes
-
ProTek's low capacitance Steering Diode Arrays provide high-speed data line and I/O port protection from transients caused by Electrostatic Discharge (ESD), Electrical Fast Transients (EFT), Tertiary Lightning and other induced voltages. Steering diodes divert the transient to the power-bus or ground and away from sensitive IC components.
-
Product
Diode Assembly
CDA&TDA
-
*Simple Installation*Low Cost*RoHS Compliant (Directive 2002/95/EC)
-
Product
Laser Diode Driver
S-101
-
LD Driver slot module of FOTS system is an efficient module that is user centered, which can drive various kinds of laser diode for the use of optical signal transmission or light source. The module has a built in LD socket, in which LD of 14 pin butterfly type is installed, which makes it possible for the user to change the LD he or she wants to drive when needed. It is leaded to get rid of the inefficiency of expense, at which various types of expensive united source module needed are purchased. By operating monitoring PD and high-performance processor that are installed inside the module, the output power and temperature of LD can be driven accurately and stably. The laser diodes can be modulated internally in square, sinusoidal, and triangular waves and its output power and temperature can also be maintained the level set by the user. In order to realize the various functions, the efficient and multi-functioned control programs with high speed processor, LCD monitor or GUI for remote control are available.
