POST Cards
read BIOS error codes during a Power On Self Test for computers unable to boot-up.
See Also: Cards, Extender Cards, Probe Cards, Test Cards, PCI Diagnostic Cards, Post Codes
-
Product
PCI Precision Resistor Card 9-Channel, 1Ω To 239Ω
50-297-113
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
10 Gbit Ethernet Card, PXIe Form Factor
ADQ10GBE
Ethernet Interface
The ADQ10GBE module enables fast network connection from a cPCIe/PXIe chassis to an external host computer. It occupies a single slot in an 3U cPCIe/PXIe chassis and can be used with backplanes supporting up to x8 Gen2 PCIe. All necessary software drivers are included and can be installed on the PXIe controller. ADQ10GBE can be used under Windows 7 (32 or 64 bit), Windows 8 and 8.1, and Linux (native support or ixgbe source code).
-
Product
PCI High Density Pecision Resistor Card, 3-Channel, 3.5Ω To 773kΩ
50-298-143
Programmable Resistor Module
The 50-298-143 is a high density programmable resistor card with 3 channels which can be set between 3.5Ω and 773kΩ with 1Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
VITA 57.4 FMC+ HSPC Loopback Card
-
Samtec's VITA 57.4 FMC+ HSPC Loopback Card provides FPGA designers an easy to use loopback option for testing low-speed and high-speed multi-gigabit transceivers on any FPGA development board or FPGA carrier card. It can run system data or BER testing on all channels in parallel. This makes evaluation and development with an FPGA much easier and is an ideal substitute for 28 Gbps test equipment.
-
Product
Signal, Module, ITA, QuadraPaddle, 90 Series, 192 Position, Fully Loaded w/ Square Posts for Wire Wrap with Anti-Rotation (610 138 122)
510151124
ITA Module
NOTE: Part # 510151124 Rev D and higher utilize captive screws that cannot be replaced with screws from currently VPC- offered screw kits.Primary mating module 510150115. (May mate with other Receiver modules, as well.)
-
Product
PCI Strain Gauge Simulator Card, 6-Channel, 350 Ohm
50-265-016
Strain Gauge Simulator
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
Product
Single Port RS422/485 Serial Communications Compact Flash Card
CF428
-
The CF428 is a tiny Type I format Compact Flash (CF+) single RS422/485 asynchronous serial port for your PDA, laptop (with an optional adapter), or desktop (using one of Elan's Desktop PCMCIA adapters).. The card automatically configures to become another COM port by using the built-in O.S. drivers that are tried and tested and are optimized to work in the Windows environment.
-
Product
VPX GPGPU Processor Card
VPX3-4924
-
Curtiss-Wright Defense Solutions
The rugged VPX3-4924 NVIDIA Tesla Pascal GPU processor board is designed and manufactured by Wolf Advanced Technology. This board is part of a family of GPGPU modules available from Curtiss-Wright Defense Solutions to enable development of High Performance Embedded Computing (HPEC) systems.
-
Product
PCI High Density Pecision Resistor Card, 4-Channel, 2.5Ω To 3.55kΩ
50-298-123
Programmable Resistor Module
The 50-298-123 is a high density programmable resistor card with 4 channels which can be set between 2.5Ω and 3.55kΩ with 1Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
DIO Function Cards
ProDAQ 3600 Series
-
The ProDAQ 3600 Series digital I/O (DIO) function cards are high-density cards that fit into ProDAQ VXIbus motherboards and LXI function card carriers. ProDAQ instruments are versatile, providing users with the highest channel density and functionality available on the market. The ProDAQ 3600 Series function cards are supplied with drivers for use with all popular software packages. The driver automatically detects and initializes all the function cards installed in one of the ProDAQ VXIbus motherboards or LXI carriers, removing any possibility of configuration errors.
-
Product
PCI High Density Pecision Resistor Card, 9-Channel, 3Ω To 52.4kΩ
50-298-033
Programmable Resistor Module
The 50-298-033 is a high density programmable resistor card with 9 channels which can be set between 3Ω and 52.4kΩ with 1Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 32.7k Ohm
50-294-032
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
48-Channel DIO Function Card
ProDAQ 3610
-
The ProDAQ 3610 high-speed DIO function card is a high-density card that fits into ProDAQ VXIbus motherboards and LXI function card carriers. This high-speed DIO card has 48 channels and is designed for demanding applications ranging from normal slow digital input/output to high-speed pattern generation and pattern recognition. The card provides the user with 384 input/output channels if eight DIO function cards are fitted to one ProDAQ motherboard.
-
Product
MIL-STD-1553 CompactPCI Interface Card
CPCIC3/6-1553-PXI
Interface Card
The CPCIC-1553/PXI Interface Card and AltaAPI Represent the Latest MIL-STD-1553 32-bit FPGA Protocol Engine Technology with Multi-Layer Software. Our Card and Software Packages are Designed for Fast, Portable Integrations. The CPCIC-1553 is the Only Commercial Off the Shelf (COTS) Card that Passes and Executes the SAE AS4111/4112 Protocol Tests.
-
Product
ccVME 16-Channel Card
EXC-1553ccVME/Px(S)
-
Each channel using the M4K1553Px module operates simultaneously as a Bus controller and/or multiple (up to 32) Remote Terminals, or as a Triggerable Bus Monitor. In addition, error injection (BC and RT modes) and error detection (all modes) are supported on each channel.
-
Product
Chrysler CCD Vehicle Bus Comms PC Card
SL100
-
The SL100 uses a standard 16450 UART with baud rate settings that makes it capable of communicating with a Chrysler CCD Vehicle bus. The SL100 uses a protected interface driver chip, as prescribed by the bus specification, to connect with vehicle peripherals in a robust and highly noise immune way. The card automatically configures to become another COM port by using the built-in O.S. drivers that are tried and tested and are optimized to work in the Windows environment.
-
Product
PCI Precision Resistor Card 6-Channel, 3Ω To 5.82MΩ
50-297-052
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
32-CH Isolated DIO Card
LPCIe-7230
Analog Input Module
ADLINK LPCIe-7230 is 32-CH isolated input and/or card. It provides a 2,500 C optical isolation protection. Two wide input range of the LPCIe-7230 makes it easy to sense the status of external devices. The non-polarity characteristic is suitable for a wide variety of industry applications. The LPCIe-7230 devices also feature a wide output range from 5 to 35 V, which is suitable for relay driving and industrial automations applications. The LPCIe-7230 also provides two interrupt sources on digital input channels, which are easily user configurable.
-
Product
16, 32, and 48 Channel Isolated Solid-State Output Cards
PCI-IDO Series
-
PCI-IDO-xx Series cards offer a range of 16, 32, or 48 individual, optically isolated differential outputs. These cards are ideal for use in control and instrumentation applications where high-voltage protection is required
-
Product
PCI Strain Gauge Simulator Card, 4-Channel, 1.5k
50-265-404
Strain Gauge Simulator
Designed to simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. It provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
Product
CPCI Avionics Bus Card
-
Avionics Bus Card is high end ARM core based MILBUS Communication Board. It is suitable for high speed Data Acquisition, Simulation, ATE applications. This board have MIL1553B, ARINC429, CCDL, digital I/O interface, USB, RS232, Ethernet interface and external bus interface. Board is well suitable for special type data acquisition & processing application. Board is based CPCI architecture and can be used with CPCI or PXI backplane. Rear IO Board is used to interface all IO’s of the board from Rear Side.
-
Product
Magnetic Stripe Card Reader
UTC-100P-M
-
Card Standard: ANSI/ISO Standards 7810,7811-1~6, 7813. Read Speed: 3 ips to 100 ips (7 cm/s to 250 cm/s). TRACK 1: IATA / 210 bpi / 79 Alphanumeric Characters.
-
Product
BNC Box-D37M To 16 SE BNC Outputs For 24-Bit PCMCIA DAQ Cards
CB218S
-
*D37M input*16 Single Ended BNC Output Channels*Connects from Ines or Elan 24-bit PCMCIA DAQ cards via CBL-T30-32-D37F cable*Only for DMM i218, AD218 or AD218/i PCMCIA DAQ cards
-
Product
Dynamically Controlled High Speed Digital I/O PXI Card
GX5290 Series
Digital I/O Module
The GX5290 Series are a high performance, cost-effective 3U PXI dynamic digital I/O boards offering 32 digital input or output channels with dynamic direction control. The GX5290 Series also supports deep pattern memory by offering 256 MB of on-board vector memory with dynamic per pin direction control and with test rates up to 200 MHz. The single board design supports both master and slave functionality without the use of add-on modules.
-
Product
Manual-Hardware 12-bit DAQ Elan/Ines PCMCIA DAQ Cards
Manual-DAQ12BHW
-
*Hardware manual for current Elan/Ines 12-Bit Data Acquisiton Cards:*DAQ ixxx Series (Standard And Multi-Function)*TS-C-ADxxx Series*TS-C-MFxxx Series
-
Product
96-Ch Digital I/O PCIE Card
PCIE-1753
-
Fully compatible with PCI-1753Up to 96 TTL digital I/O linesEmulates mode 0 of 8255 PPISupports both dry and wet contactInterrupt handling capabilityOutput status read-backSupports input data pattern match and change of state functionsKeep I/O settings and output status after hot resetBuffered circuits for higher driving capacity than the 8255High-density 100-pin SCSI connector
-
Product
PCI High Density Potentiometer Card 4-Channel, 16-Bit, 0 To 65k Ohm
50-296A-121-4/16
Programmable Potentiometer
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
High-Density Matrix Switch Card
1260-43
Matrix Switch Module
The Astronics 1260-43 is a high-density matrix switch card. Each module consists of three 8x24 single-wire matrices, which are interconnected via a 10-lane, single-wire bus. On-board configuration relays allow software control of the matrix configuration.
-
Product
PCI High Density Pecision Resistor Card, 6-Channel, 3.5Ω To 201kΩ
50-298-041
Programmable Resistor Module
The 50-298-041 is a high density programmable resistor card with 6 channels which can be set between 3.5Ω and 201kΩ with 0.25Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI Resistor Card 2-Channel 2 Ohm To 131k Ohm
50-293-034
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
