Force Transducers
-
Product
Pressure Transducers and Transmitters
-
AMETEK Sensors, Test & Calibration
We provide some of the world’s most popular pressure transducers and pressure transmitters for a variety of applications and markets. For more information contact Us
-
Product
General Purpose Quartz Force Sensors
-
General purpose force sensors are offered in either stud or axial mounted configurations. They are internally pre-loaded and can be used for dynamic compression, tension, and impact force measurements. Tapped mounting holes on both ends of the radial connector style support link, platform, integrated link, and free-standing installations. The axial mounted type offers protection of the electrical connector and sensor cable from potential damage during drop testing and in free-standing installations. Supplied impact caps facilitate impact and drop force measurements.
-
-
Product
Crimp Force Monitor
638007950
-
The crimp force monitor measures the force signature of a crimped terminal and compares it to a reference crimp. Depending on the limits programmed, the measurement will pass, fail, or be suspect.
-
Product
Ergonomics Force Gauges
Series E
-
Series E push / pull force gauges make job task analysis and ergonomics analysis simple and accurate, ideal for workplace design, strength assessment, and ergonomic studies. Series E presents the ergonomist and other professionals with a simple and economical testing solution. 100 lbF, 200 lbF and 500 lbF (500, 2,500, and 5,000 N) capacity force gauges are available, along with a wide range of attachments for various applications.
-
Product
Non Contact Flange Torque Transducer
FF425
-
Contactless Torque Transducers with flange couplings at either end with measuring ranges from 0-100Nm up to 30kNm as standard (bespoke sensors up to 16MNm) for a variety of in line static and rotary torque measurement applications.The Datum Electronics Series FF425 non contact flange torque sensor and FF410 torque sensors have been designed to fit easily inline with any drive train or test rig using standard DIN size couplings. With Flange couplings at either end of the torque transducer, it has many advantages over other torque measurement systems on the market.
-
Product
Shear Wave Transducers
-
At Precision Acoustics, we manufacture normal incidence shear wave probes at 1 MHz, which can be coupled directly to an object through a shear wave coupling gel.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type H, Ø0.80mm, 230gf
K100-H080230-SKAU
-
K100 Series, Pitch 100mil, Tip Style H, Tip Diameter Ø0.80mm, Spring force 230gf, Steel with Gold Plating.
-
Product
Force Gauges
-
A digital force gauge, often called a push pull force gauge or tension and compression force gauge, is used in material testing, quality control and assurance, research, development, product testing, laboratory and educational applications. PCE Instruments' (PCE) digital force gauge products are the benchmark of quality and performance. PCE digital force gauge devices provide measurements in kilograms (kg), grams (g), ounces (oz), pounds (lbs) and Newtons (N) of force (f), depending on the force gauge model. Most PCE digital force gauge products are handheld, portable devices that also can be used with a universal test stand. There are several different force gauge products available online in the PCE web shop.
-
Product
Ergonomic Force Gauges
MSE100 Series
-
AMETEK Sensors, Test & Calibration
The MSE100 ergonomic gauge is a simple-to-use, ergonomically designed mechanical instrument ideal for muscle strength evaluations and job task analysis.
-
Product
Mechanical Force Gauges
-
Imada mechanical force gauges are highly accurate instruments used to test the quality, strength or functionality of component parts or products. Imada mechanical force gauges check both compression and tension (push or pull). Peak force can be captured using the peak indicator needle and the tare ring compensates for the weight of attachments. Imada force gauges are constructed with a heavy-duty metal case and all metal components to enable them to retain their calibration for years with proper care. These mechanical force gauges never need charging or batteries and are intrinsically safe in hazardous environments.
-
Product
Mechanical Force Gauges
-
The mechanical force gauges from Chatillon offer high precision compression testing (Push) and tensile testing (Pull) at a low cost on a wide range of testing applications.
-
Product
ThermalAir Series Temperature Forcing System
ThermalAir TA-3000A
-
The ThermalAir TA-3000 high capacity thermal air stream system is used for temperature testing, fast thermal cycling, and device temperature characterization of components, hybrids, modules, PCBs, and other electronic and non-electronic assemblies at precise temperature from -65°C to +225°C. Compact! Plus Performance!
-
Product
Acquisition Of 16 Displacement Transducers
APCI-3701-16
-
PCI interface to the 32-bit data bus Acquisition of 16 inductive displacement transducers (Half Bridge, LVDT) 16 input channels ± 10 V 16-bit resolution Measuring frequency up to 100 kHz Conversion can be triggered through software End of conversion can be inquired through software Possibility of interrupt through digital input channels (when a data or a time value is exceeded) PCI-DMA access Onboard FIFO buffers Sequence RAM 16 isolated digital I/O, 24 V Software operation Supported inductive transducers for APCI-3701Standard board APCI-3701-8 or APCI-3701-16Transducer type:
-
Product
AC Current Transducer
iDVM 333
-
The iDVM 333 AC Current Transducer plugs into the iDVM 510 multimeter and measures current (as AC millivolts) with no need to break the circuit. Special Introductory Price: $52.50FeaturesTransformer jaws that detect AC current flowing through a conductorSelectable sensitivity between 1mV/A and 10mV/AHand Guard to protect your hand for safetyLarge, easy-to-operate trigger opens the transformer jaws
-
Product
Quartz Charge Force Rings
-
Ring-style sensor configurations measure dynamic compression. Tension measurements are also possible if the unit has been installed with proper pre-load.
-
Product
ThermalAir Series Temperature Forcing System
ThermalAir TA-3000B
-
The ThermalAir TA-3000B high capacity thermal air stream system is used for temperature testing, fast thermal cycling, and device temperature characterization of components, hybrids, modules, PCBs, and other electronic and non-electronic assemblies at precise temperature from -65°C to +225°C. Compact! Plus Performance!
-
Product
Computer Conversions GT Transducers
H35
-
Computer Conversions Corporation
Computer Conversions GT Transducers are brushless, Electromagnetic, Rotary Sensors used to provide Precise Absolute or Incremental Position, and Velocity feedback in harsh environments. All Computer Conversions Transducers are continuous rotation, bi-directional, and electronically passive devices (no electronic components to degrade or fail), that require zero maintenance, and may be installed in virtually inaccessible locations.
-
-
Product
Force Measurement
-
Imada offers a complete selection of force measurement tools including force gauges, test stands and attachments. The gauges can be used by hand or combined into customized force measurement systems capable of addressing a wide variety of applications and budgets.
-
-
Product
Industrial Pressure Transducers
-
These industrial Baratron® capacitance manometers feature industrial enclosures and higher operating temperature ranges for industrial pressure measurement applications.
-
Product
Force Gauge
-
Shenzhen Graigar Technology Co.,Ltd.
A force gauge is a small measuring instrument used across all industries to measure the force during a push or pull test. Applications exist in research and development, laboratory, quality, production and field environment.
-
Product
Cobra Temperature Forcing System for ATE/SLT Test Applications
31000R
-
Cobra is the most advanced, compact,powerful temperature-forcing system on the market. Cobra is an adaptable solution to the ever-increasing thermal demands of post silicon validation and device characterization.
-
Product
Acoustic Emission Transducer
GT200
-
Acoustic emission transducer is a key element of non-destructive acoustic emission testing. Transducers GT 200 are used for technical diagnostics by means of passive ultrasound.
-
Product
PVdF Transducers
-
PVdF transducers have a wide bandwidth, short impulse response and can be designed to your specific requirement.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type L, Ø1.50mm, 155gf
K100-L150155-SKAU
-
K100 Series, Pitch 100mil, Tip Style L, Tip Diameter Ø1.50mm, Spring force 155gf, Steel with Gold Plating.
-
Product
Force Gauges
-
SHIMPO offers a range of digital and mechanical force gauges to suite every application from low capacities (0.5 lbs) to high capacities (1,000 lbs). Our gauge's features range from simple, no output models to highly sophisticated units that provide memory, statistics and data output. Our gauges are known for their strong construction and highly accurate measurements.
-
Product
Torque Transducer
T12HP
-
One torque sensor, multiple functions only T12HP can do this. Its superior basic accuracy guarantees precise values over the entire measurement range. This results in the FlexRange capability that only T12HP can provide without the need to switch the measuring range like so called dual range sensors do.
-
Product
Reference Pressure Transducers
-
These Baratron® capacitance manometers offer our highest level of presure measurement accuracy making them ideal for calibration transfer standards.
