Test Pattern
Test signals for the calibration and alignment of TV broadcast and reception equipment.
-
Product
Test Adapter
RAMCHECK® SIMM
-
The RAMCHECK SIMM Adapter is another addition to the RAMCHECK memory tester. It provides a needed solution for testing older 72-pin EDO/FPM DRAM SIMM modules. An optional adapter for 30 and 72-pin SIMMs is also available
-
-
Product
Test SIP
-
VoIP, Video, and IPTV products must withstand and continue to function when facing all the conditions that occur on the Internet. These include attacks from hackers exploiting vulnerabilities in security and protocols as well as the common phenomenon of congestion, delay, jitter, drops, and so on. VoIP, Video, and IPTV products must demonstrate robustness and resiliency in the face of unusual and/or illegal conditions.
-
Product
Hi-Pot Testing
-
The CableEye HVX System combines our M3U tester with a high voltage module to provide Hi-Pot testing of insulation resistance and dielectric breakdown up to 1500Vdc and 1000Vac.
-
Product
Package Testing
-
AMERICAN TESTING LABORATORY tests all types of product packaging, from shipping crates to child resistant packaging. In addition, we test the effects of many types of physical and environmental shocks on products inside the packaging.
-
Product
Testing Equipment
-
Our product line of material testing equipment can perform several different types of tests and on different types of samples in tension and compression. With our testing software Califort, simply press the green arrow and your tests and measurements start.
-
Product
Design for Test
-
Test Coach offers Design for Test (DFT) consulting to assist customers with design review of prototype boards prior to release for production. Design for Test analysis is extremely important in ensuring that an assembly will achieve the highest possible test coverage. For ICT, this DFT will review the board to confirm that the bed-of-nails test fixture can be fabricated to test an assembly without sacrificing test coverage. As with ICT, Flying Probe benefits from DFT analysis by reviewing test point access and mechanical challenges that may affect the potential test coverage. Completing a DFT enables Test Coach to make recommendations to our customers that may be implemented on boards during the design phase which will allow for the most comprehensive coverage at time of test.
-
Product
Impact Testing
-
The Impact Testing software of the m+p Analyzer real time analyzer includes useful tools like the selection of a roving hammer or transducer, selection of data points/nodes, double impact detection and rejection, definition of force and exponential window and a user-definable display configuration as a visual measurement feedback.
-
Product
5G Testing
-
Teradyne test solutions are at the forefront of the 5G test era. Why? We work with the leading semiconductor manufacturers and provide optimized test coverage for the major wireless standards. From emerging millimeter wave devices to the traditional sub-6GHz, our test solutions are already leading the way.
-
Product
Electrical Testing
-
Innovative Testing Solutions, Inc.
Our specialty is Direct Current automotive components. We perform product validation and design verification testing on both electrical components and systems. Also, we perform warranty investigation testing and failure analysis. We have voltage capabilities to 300 volts and current capabilities to 1000 amperes. Both two-wire and four-wire resistance measurements are supported from NanoOhms to GigaOhms.
-
Product
Strength Testing
-
Sataton Instruments Technology CO., Ltd
Air permeability tester is professional designed to determine the permeability of materials to air. By testing the rate of flow of air passing perpendicularly through a given area of tested sample under a given pressure over a given time period, the tester can provide results of air permeability performance by calculation the indices. The air permeability testing instrument is applicable to many type of materials, including industrial fabrics, nonwovens, made-up textiles, paper and board, foam and other materials.
-
Product
Wireless/RF Testing
-
NCEE’s experienced iNarte EMC/EMI qualified staff provide wireless and radio frequency (RF) testing of intentional radiators to ensure they meet the FCC, CE, and many other international regulatory requirements for transmitting and receiving (radio) devices. Frequent regulatory changes and complex testing requirements are common with wireless/RF equipment. NCEE Labs stays current with the most recent requirements and can help you navigate your requirements while supplying quality testing services to demonstrate worldwide compliance!
-
Product
Test System
LB301
-
Computer Gesteuerte Systeme GmbH
The system is pin and software compatible to the larger test systems LB302 / 303. Due to the fewer needed I/Os, the tester features the compact G6 receiver (Virginia Panel Cooperation) compared to the larger G12 of the other tester versions. The LB301 is equipped with a 2kW power supply and can control one load box.
-
Product
Interactive Benchtop Test
-
Strict time-to-market deadlines make it vital to efficiently debug and validate product designs. Virtual instrumentation provides a unified interface that gives engineers an advantage over traditional box instruments.
-
Product
EMS Test System
TS9982
-
The R&S®TS9982 is the base system for conducted and radiated EMS measurements. Due to its modular design, it covers a wide range of applications and can be very easily adapted to the measurement task at hand. Any configuration is possible – from conducted measurements and the small precompliance system with a compact test cell to the accredited test system for complete motor vehicles with 200 V/m.
-
Product
Portable Logic Analyzer & Digital Pattern Generator
Digital Discovery
-
The Digital Discovery is designed to be the ultimate embedded development companion. Configured and controlled by the full featured WaveForms 2015 software toolset, the Digital Discovery provides a Logic Analyzer, Pattern Generator, Digital IO, Protocol Analyzer and Script Editor. Equipped with a Xilinx Spartan 6 FPGA, the Digital Discovery can provide up to 32 channels and up to 800MSPS. Thats 8 times the sample rate of the Analog Discovery!
-
Product
Battery Test
1260
-
*Basic Battery Load Test*Battery Analysis*Mac*Test*Bad Cell Indicators*Testing the Starter Motor*Low Temperatures Effects
-
Product
Compression/Tensile Testing
-
For testing of strength in tension, compression, bending, shearing, rapture and etc.It can be used for various raw materials, semi-finished and finished products which are essential to manufacturers performing quality control & academic organizations for studying the physical properties of raw materials
-
Product
Supercapacitor Test
-
The CT3001A/C battery test systems are upgraded from CT2001A/C with higher precision and data logging rate. The tester can be used to run precision tests for coin cells, pouch cells, prismatic cells, and especially supercapacitors (ultra-capacitors). Each tester has 8 independent channel which can be programmed to run constant current charge/discharge, constant voltage charge, constant power discharge, constant resistant discharge, and direct current internal resistance (DCIR) tests.
-
Product
Test Equipment
ST9020
-
Shenzhen Star Instrument Co., Ltd.
The ST9020 single-phase energy meter test equipment is full-featured and stable. Optional accuracy classes are 0.1 and 0.05. As divided by structure there are combined type, integrated type and auto wiring type. The meter test equipment is controlled via PC-based software. Choices of meter position are 6, 12, 24, 30, 48 and 60.
-
Product
Security Testing
-
For an application to be successful, it has to ensure the security of the customer’s data, which in turn helps to gain the trust of the customers, avoid legal battles, and enables growth in business.
-
Product
Test Suite
IEC 61850
-
The Test Suite is a group of Windows application that support IEC 61850 as well as IEC 60870-6 (TASE.2/ ICCP). New InSight functionality allows creation of custom graphical displays and scripted simulation design/debug via flowchart GUI. The Test Suite is comprised of three separate products.
-
Product
NI Real-Time Test Cell Reference System
778820-35
-
DIAdem Advanced with DAC Bundle, Perpetual License, Include 1 Year SSP
-
Product
SAR Testing
-
RF transmitters used in close proximity to the human body must be evaluated against human Exposure standards which set basic restrictions for the Specific Absorption Rate (SAR) of RF energy by any part of the human body. This may include two-way radios, cellular phones, smartphones, spread spectrum, Bluetooth devices, wireless EFTPOS terminals and WLAN devices used in PDA/notebook/laptop/tablet computers. In Australia and Europe, virtually all devices exceeding the power threshold of 20mW (13dBm) and used in close proximity to the human body must comply with SAR requirements. There is no such blanket exemption in the USA and Canada where each product must be assessed against frequency/power level criteria.
-
-
Product
PXI Integration Platform
ATS-3100
-
The new ATS-3100 enables you to rise above the module level and shift your focus to the sophisticated test solution you’re actually building. Simply add your instruments, software, and customization to create a complete solution. Or, if you're short on time or resources, ask Astronics Test Systems to do the finishing work for you.
-
Product
Ground Testing
-
Ensuring an effective earth system is essential in a telecommunications system, and Megger is expert in earth testing having been there right from the start. These days Megger offers top end systems for design and soil surveys as well as tough easy to use testers for field engineers. We have tried to make the testers self checking as much as we can, to allow you to concentrate on collating and understanding the results.
-
Product
Transformer Testing
-
Haomai Electric Power Automation Co.,Ltd.
1)Test Standard:IEC60076 & IEEE C57.12.90 2)Voltage ratio measurement of transformer 3)Turns ratio measurement of transformer 4)Group vector measurement of transformer
-
Product
Bond Testing
-
Our complete line of bond testing (BT) flaw detectors provides unmatched capabilities for the location of discontinuities and other flaws in composite structures. We offer a wide range of measurement features and application-specific options for flaw detection.
-
Product
Test Programming
-
Terotest offers a full test programming service for all of our Automatic Test Equipment. In many cases test programs can be generated from CAD data on the product or component under test, or from autolearn facilities within the test system. Such techniques maximise accuracy and test program fault coverage, and allow quick and easy test program generation.
